Self-sealed vertical polymeric nanoporous-junctions for high-throughput nanofluidic applications

Nanofluidic preconcentration device in a straight microchannel using ion concentration polarization

In this paper, we introduce a simple, straight microchannel design for a nanofluidic protein concentration device. Compared with concentration devices previously developed, the anode channel and cathode channel in this new concentration scheme are both integrated into a straight microchannel, with one inlet and one outlet. Most of the functions of a conventional two-channel concentration device can be achieved by this concentration device, and the efficiency of sample accumulation can be controlled by the dimension of the Nafion membrane. Also, the operating mechanism of this device was tested on various material combinations such as PDMS (polydimethyl-siloxane) channel-glass substrate and silicon channel-PDMS substrate. Using a combined PDMS-silicon device which was sealed reversibly without plasma bonding, surface based immunoassay for concentrator-enhanced detection of clinically relevant samples such as C-reactive protein (CRP) was demonstrated. As a result, it was possible to enhance the detection sensitivity of the immunoassay by more than 500 folds compared to the immunoassay without preconcentration process.

Nanofracture on fused silica microchannel for Donnan exclusion based electrokinetic stacking of biomolecules

Due to Donnan exclusion, charged molecules are prohibited from passing through a channel of electrical double layer scale (nanometers), even though the molecules are smaller than the lowest dimension of the channel. To employ this effect for on-chip pre-concentration, an ion channel of nanometer scale has to be introduced. Here we introduced a simple method of generating a fracture (11-250 nm) directly on the commercially available open tubular fused silica capillary, and a chip comprised of the capillary with the nanofracture was prepared. A ring-disk model of the fracture was derived with which the fracture width can be easily characterized online without any damage to the chip, and the result was validated by a scanning electron microscope (SEM). The fractures can be used directly as a nanofluidic interface exhibiting an obvious ion concentration polarization effect with high current flux. On-chip electrokinetic stacking of SYBR Green I labeled λDNA inside the capillary was successfully demonstrated, and a concentration factor close to the amplification rate of the polymerase chain reaction (PCR) was achieved within 7 min. The chip is inexpensive and easy to prepare in common chemistry and biochemistry laboratories without limitations in expensive microfabrication facilities and sophisticated expertise. More applications of this interface could be found for enhancing the detectability of capillary based microfluidic analytical systems for the analysis of low concentrated charged species.

Optofluidic concentration: plasmonic nanostructure as concentrator and sensor

The integration of fluidics and optics, as in flow-through nanohole arrays, has enabled increased transport of analytes to sensing surfaces. Limits of detection, however, are fundamentally limited by local analyte concentration. We employ the nanohole array geometry and the conducting nature of the film to actively concentrate analyte within the sensor. We achieve 180-fold enrichment of a dye, and 100-fold enrichment and simultaneous sensing of a protein in less than 1 min. The method presents opportunities for an order of magnitude increase in sensing speed and 2 orders of magnitude improvement in limit of detection.

Coupled concentration polarization and electroosmotic circulation near micro/nanointerfaces: Taylor-Aris model of hydrodynamic dispersion and limits of its applicability

Mismatches in electrokinetic properties between micro- and nanochannels give rise to superposition of electroosmotic and pressure-driven flows in the microchannels. Parabolic or similar flow profiles are known to cause the so-called hydrodynamic dispersion, which under certain conditions can be formally assimilated to an increase in the solute diffusivity (Taylor-Aris model). It is demonstrated theoretically that taking into account these phenomena modifies considerably the pattern of current-induced concentration polarization of micro/nanointerfaces as compared to the classical model of unstirred boundary layer. In particular, the hydrodynamic dispersion leads to disappearance of limiting current. At essentially "over-limiting" current densities, the time-dependent profiles of salt concentration in microchannels behave like sharp concentration "fronts" moving away from the interface until they reach the reservoir end of the microchannel. Under galvanostatic conditions postulated in this study, these "fronts" move with practically constant speed directly proportional to the current density. The sharp transition from a low-concentration to a high-concentration zone can be useful for the analyte preconcentration via stacking. The pattern of moving sharp concentration "fronts" has been predicted for the first time for relatively broad microchannels with negligible surface conductance. The Taylor-Aris approach to the description of hydrodynamic dispersion is quantitatively applicable only to the analysis of sufficiently "slow" processes (as compared to the characteristic time of diffusion relaxation in the transversal direction). A posteriori estimates reveal that the condition of "slow" processes is typically not satisfied close to current-polarized micro/nanointerfaces. Accordingly, to make the description quantitative, one needs to go beyond the Taylor-Aris approximation, which will be attempted in future studies. It is argued that doing so would make even stronger the dampening impact of hydrodynamic dispersion on the current-induced concentration polarization of micro/nanointerfaces.

Flexible fabrication and applications of polymer nanochannels and nanoslits

Fluidic devices that employ nanoscale structures (<100 nm in one or two dimensions, slits or channels, respectively) are generating great interest due to the unique properties afforded by this size domain compared to their micro-scale counterparts. Examples of interesting nanoscale phenomena include the ability to preconcentrate ionic species at extremely high levels due to ion selective migration, unique molecular separation modalities, confined environments to allow biopolymer stretching and elongation and solid-phase bioreactions that are not constrained by mass transport artifacts. Indeed, many examples in the literature have demonstrated these unique opportunities, although predominately using glass, fused silica or silicon as the substrate material. Polymer microfluidics has established itself as an alternative to glass, fused silica, or silicon-based fluidic devices. The primary advantages arising from the use of polymers are the diverse fabrication protocols that can be used to produce the desired structures, the extensive array of physiochemical properties associated with different polymeric materials, and the simple and robust modification strategies that can be employed to alter the substrate's surface chemistry. However, while the strengths of polymer microfluidics is currently being realized, the evolution of polymer-based nanofluidics has only recently been reported. In this critical review, the opportunities afforded by polymer-based nanofluidics will be discussed using both elastomeric and thermoplastic materials. In particular, various fabrication modalities will be discussed along with the nanometre size domains that they can achieve for both elastomer and thermoplastic materials. Different polymer substrates that can be used for nanofluidics will be presented along with comparisons to inorganic nanodevices and the consequences of material differences on the fabrication and operation of nanofluidic devices (257 references).

Massively parallel concentration device for multiplexed immunoassays

A massively parallel nanofluidic concentration device array for multiplexed and high-throughput biomolecule detection is demonstrated. By optimizing the microchannel/nanojunction design and channel conductivity, an array of up to 128 nanofluidic concentration devices were fabricated. Operation of the entire array requires only one inlet and one outlet reservoir, with the application of a single operational voltage bias across them. Concentration efficiencies of the devices were found to be uniform within the array, within 5% error. Alternatively, concentration speed in each channel can be individually tuned by controlling the length of the inlet microchannel and thus controlling the flow rate based on change of the tangential electric field. This allows immuno-binding reactions at different concentration ranges to be performed in parallel. Using multiplexed, successive-concentration enhanced detection in the device, we have shown that the dynamic range and reliability of the immunoassay can be significantly increased.

Radial sample preconcentration

In this paper we present a radial sample preconcentration strategy enabled by axisymmetric concentration polarization in a microfluidic chamber on a uniform nanoporous film. Sample analytes are focused into the centre, creating a concentrated plug that is injected vertically into the microfluidic analysis layer. No balancing pressure driven flows or tangential fields are required, and the process has essentially zero footprint on the analysis layer. An electrokinetic loading scheme enables repeat loading/concentration cycles, and a finned radial chamber geometry dampens instabilities and accommodates larger volumes. Modelling results indicate over 1800-fold concentration increases are possible in 10 s, for high mobility buffers and high applied field strength. At moderate field strength and buffer mobility, experiments demonstrate a 168-fold increase in concentration of FITC-BSA protein in 36 s.

Recent advances in enhancing the sensitivity of electrophoresis and electrochromatography in capillaries and microchips (2008-2010)

Capillary electrophoresis has been alive for over two decades now; yet, its sensitivity is still regarded as being inferior to that of more traditional methods of separation such as HPLC. As such, it is unsurprising that overcoming this issue still generates much scientific interest. This review continues to update this series of reviews, first published in Electrophoresis in 2007, with an update published in 2009 and covers material published through to June 2010. It includes developments in the fields of stacking, covering all methods from field-amplified sample stacking and large volume sample stacking, through to ITP, dynamic pH junction and sweeping. Attention is also given to on-line or in-line extraction methods that have been used for electrophoresis.

A robust nanofluidic membrane with tunable zero-order release for implantable dose specific drug delivery

This manuscript demonstrates a mechanically robust implantable nanofluidic membrane capable of tunable long-term zero-order release of therapeutic agents in ranges relevant for clinical applications. The membrane, with nanochannels as small as 5 nm, allows for the independent control of both dosage and mechanical strength through the integration of high-density short nanochannels parallel to the membrane surface with perpendicular micro- and macrochannels for interfacing with the ambient solutions. These nanofluidic membranes are created using precision silicon fabrication techniques on silicon-on-insulator substrates enabling exquisite control over the monodispersed nanochannel dimensions and surface roughness. Zero-order release of analytes is achieved by exploiting molecule to surface interactions which dominate diffusive transport when fluids are confined to the nanoscale. In this study we investigate the nanofluidic membrane performance using custom diffusion and gas testing apparatuses to quantify molecular release rate and process uniformity as well as mechanical strength using a gas based burst test. The kinetics of the constrained zero-order release is probed with molecules presenting a range of sizes, charge states, and structural conformations. Finally, an optimal ratio of the molecular hydrodynamic diameter to the nanochannel dimension is determined to assure zero-order release for each tested molecule.

High yield sample preconcentration using a highly ion-conductive charge-selective polymer

The development and analysis of a microfluidic sample preconcentration system using a highly ion-conductive charge-selective polymer [poly-AMPS (2-acrylamido-2-methyl-1-propanesulfonic acid)] is reported. The preconcentration is based on the phenomenon of concentration polarization which develops at the boundaries of the poly-AMPS with buffer solutions. A negatively charged polymer, poly-AMPS, positioned between two microchannels efficiently extracts cations through its large cross section, resulting in efficient anion sample preconcentration. The present work includes the development of a robust polymer that is stable over a wide range of buffers with varying chemical compositions. The sample preconcentration effect remains linear to over 3 mM (0.15 pmol) and 500 microM (15 fmol) for fluorescein and TRITC-tagged albumin solutions, respectively. The system can potentially be used for concentrating proteins on microfluidic devices with subsequent analysis for proteomic applications.

Capillary-valve-based fabrication of ion-selective membrane junction for electrokinetic sample preconcentration in PDMS chip

In this paper, we report a novel method for fabricating ion-selective membranes in poly(dimethylsiloxane) (PDMS)/glass-based microfluidic preconcentrators. Based on the concept of capillary valves, this fabrication method involves filling a lithographically patterned junction between two microchannels with an ion-selective material such as Nafion resin; subsequent curing results in a high aspect-ratio membrane for use in electrokinetic sample preconcentration. To demonstrate the concentration performance of this high-aspect-ratio, ion-selective membrane, we integrated the preconcentrator with a surface-based immunoassay for R-Phycoerythrin (RPE). Using a 1x PBS buffer system, the preconcentrator-enhanced immunoassay showed an approximately 100x improvement in sensitivity within 30 min. This is the first time that an electrokinetic microfluidic preconcentrator based on ion concentration polarization (ICP) has been used in high ionic strength buffer solutions to enhance the sensitivity of a surface-based immunoassay.

Integrated Multi-process Microfluidic Systems for Automating Analysis

Microfluidic technologies have been applied extensively in rapid sample analysis. Some current challenges for standard microfluidic systems are relatively high detection limits, and reduced resolving power and peak capacity compared to conventional approaches. The integration of multiple functions and components onto a single platform can overcome these separation and detection limitations of microfluidics. Multiplexed systems can greatly increase peak capacity in multidimensional separations and can increase sample throughput by analyzing many samples simultaneously. On-chip sample preparation, including labeling, preconcentration, cleanup and amplification, can all serve to speed up and automate processes in integrated microfluidic systems. This paper summarizes advances in integrated multi-process microfluidic systems for automated analysis, their benefits and areas for needed improvement.

SlipChip for immunoassays in nanoliter volumes

This article describes a SlipChip-based approach to perform bead-based heterogeneous immunoassays with multiple nanoliter-volume samples. As a potential device to analyze the output of the chemistrode, the performance of this platform was tested using low concentrations of biomolecules. Two strategies to perform the immunoassay in the SlipChip were tested: (1) a unidirectional slipping method to combine the well containing a sample with a series of wells preloaded with reagents and (2) a back-and-forth slipping method to introduce a series of reagents to a well containing the sample by reloading and slipping the well containing the reagent. The SlipChips were fabricated with hydrophilic surfaces on the interior of the wells and with hydrophobic surfaces on the face of the SlipChip to enhance filling, transferring, and maintaining aqueous solutions in shallow wells. Nanopatterning was used to increase the hydrophobic nature of the SlipChip surface. Magnetic beads containing the capture antibody were efficiently transferred between wells and washed by serial dilution. An insulin immunoenzymatic assay showed a detection of limit of approximately 13 pM. A total of 48 droplets of nanoliter volume were analyzed in parallel, including an on-chip calibration. The design of the SlipChip is flexible to accommodate other types of immunoassays, both heterogeneous and homogeneous. This work establishes the possibility of using SlipChip-based immunoassays in small volumes for a range of possible applications, including analysis of plugs from a chemistrode, detection of molecules from single cells, and diagnostic monitoring.

Direct seawater desalination by ion concentration polarization

A shortage of fresh water is one of the acute challenges facing the world today. An energy-efficient approach to converting sea water into fresh water could be of substantial benefit, but current desalination methods require high power consumption and operating costs or large-scale infrastructures, which make them difficult to implement in resource-limited settings or in disaster scenarios. Here, we report a process for converting sea water (salinity approximately 500 mM or approximately 30,000 mg l(-1)) to fresh water (salinity <10 mM or <600 mg l(-1)) in which a continuous stream of sea water is divided into desalted and concentrated streams by ion concentration polarization, a phenomenon that occurs when an ion current is passed through ion-selective membranes. During operation, both salts and larger particles (cells, viruses and microorganisms) are pushed away from the membrane (a nanochannel or nanoporous membrane), which significantly reduces the possibility of membrane fouling and salt accumulation, thus avoiding two problems that plague other membrane filtration methods. To implement this approach, a simple microfluidic device was fabricated and shown to be capable of continuous desalination of sea water (approximately 99% salt rejection at 50% recovery rate) at a power consumption of less than 3.5 Wh l(-1), which is comparable to current state-of-the-art systems. Rather than competing with larger desalination plants, the method could be used to make small- or medium-scale systems, with the possibility of battery-powered operation.

Nanofluidic concentration devices for biomolecules utilizing ion concentration polarization: theory, fabrication, and applications

Recently, a new type of electrokinetic concentration devices has been developed in a microfluidic chip format, which allows efficient trapping and concentration of biomolecules by utilizing ion concentration polarization near nanofluidic structures. These devices have drawn much attention not only due to their potential application in biomolecule sensing, but also due to the rich scientific content related to ion concentration polarization, the underlying physical phenomenon for the operation of these electrokinetic concentration devices. This tutorial review provides an introduction to the scientific and engineering advances achieved, in-depth discussion about several interesting applications of these unique concentration devices, and their current limitations and challenges.

Stabilization of ion concentration polarization using a heterogeneous nanoporous junction

We demonstrate a recycled ion-flux through heterogeneous nanoporous junctions, which induce stable ion concentration polarization with an electric field. The nanoporous junctions are based on integration of ionic hydrogels whose surfaces are negatively or positively charged for cationic or anionic selectivity, respectively. Such heterogeneous junctions can be matched up in a way to achieve continuous ion-flux operation for stable concentration gradient or ionic conductance. Furthermore, the combined junctions can be used to accumulate ions on a specific region of the device.

A method for nanofluidic device prototyping using elastomeric collapse

Nanofluidics represents a promising solution to problems in fields ranging from biomolecular analysis to optical property tuning. Recently a number of simple nanofluidic fabrication techniques have been introduced that exploit the deformability of elastomeric materials like polydimethylsiloxane (PDMS). These techniques are limited by the complexity of the devices that can be fabricated, which can only create straight or irregular channels normal to the direction of an applied strain. Here, we report a technique for nanofluidic fabrication based on the controlled collapse of microchannel structures. As is demonstrated, this method converts the easy to control vertical dimension of a PDMS mold to the lateral dimension of a nanochannel. We demonstrate here the creation of complex nanochannel structures as small as 60 nm and provide simple design rules for determining the conditions under which nanochannel formation will occur. The applicability of the technique to biomolecular analysis is demonstrated by showing DNA elongation in a nanochannel and a technique for optofluidic surface enhanced Raman detection of nucleic acids.

High speed nanofluidic protein accumulator

Highly efficient preconcentration is a crucial prerequisite to the identification of important protein biomarkers with extremely low abundance in target biofluids. In this work, poly(dimethylsiloxane) microchips integrated with 10 nm polycarbonate nanopore membranes were utilized as high-speed protein accumulators. Double-sided injection control of electrokinetic fluid flow in the sample channel resulted in highly localized protein accumulation at a very sharp point in the channel cross point. This greatly enhanced the ability to detect very low levels of initial protein concentration. Fluorescein labeled human serum albumin solutions of 30 and 300 pM accumulated to 3 and 30 microM in only 100 s. Initial solutions as low as 0.3 and 3 pM could be concentrated within 200 s to 0.3 and 3 microM, respectively. This demonstrates a approximately 10(5)-10(6) accumulation factor, and an accumulation rate as high as 5000/sec, yielding a >10x improvement over most results reported to date.

Amplified electrokinetic response by concentration polarization near nanofluidic channel

Ion concentration polarization is the fundamental transport phenomenon that occurs near ion-selective membranes, but this important membrane phenomenon has been poorly understood due to theoretical and experimental challenges. Here, we report the first direct measurements of detailed flow and electric potential profiles within and near the depletion region. This work is an important step toward a full characterization of this coupled transport problem. Using microfabricated electrodes integrated with the microfluidic device, we measured and confirmed that the electric field inside an ion depletion region is amplified more than 30-fold compared to outside of the depletion zone due to the highly nonuniform ion concentration distribution along the microchannel. As a result, the electrokinetic motion of both fluid (electroosmosis) and particle (electrophoresis) was significantly amplified. The detailed flow profile within the depletion zone was also measured for the first time by optically tracking photobleached neutral dye molecules. We further showed that the amplified electrokinetic flows generated in this device may be used as a field-controlled, microfluidic fluid pump and switch.

On the propagation of concentration polarization from microchannel-nanochannel interfaces. Part II: Numerical and experimental study

We present results of a combined computational and experimental study of the propagation of concentration polarization (CP) zones in a microchannel-nanochannel system. Our computational model considers the combined effects of bulk flow, electromigration, and diffusion and accurately captures the dynamics of CP. Using wall charge inside the nanochannel as a single fitting parameter, we predict experimentally observed enrichment and depletion shock velocities. Our model can also be used to compute the existence of CP with propagating enrichment and depletion shocks on the basis of measured ion mobility and wall properties. We present experiments where the background electrolyte consists of only a fluorescent ion and its counterion. These results are used to validate the computational model and to confirm predicted trends from an analytical model presented in the first of this two-paper series. We show experimentally that the enrichment region concentration is effectively independent of the applied current, while the enrichment and depletion shock velocities increase in proportion to current density.

In situ fabrication of ionic polyacrylamide-based preconcentrator on a simple poly(methyl methacrylate) microfluidic chip for capillary electrophoresis of anionic compounds

A simple and efficient method was developed for fabrication of an anionic sample preconcentrator on a channel of a commercial poly(methyl methacrylate) (PMMA)-made microchip using no photolithography or etching technique. The originality of our preconcentrator is based on simple photochemical copolymerization of monomers using the following procedure: All channels of the PMMA-made microchip were filled with gel solution comprising acrylamide, N,N'-methylene-bisacrylamide, and 2-acrylamide-2-methylpropanesulfonic acid with riboflavin as a photocatalytic initiator. In situ polymerization near the cross of the sample outlet channel was performed by irradiation with an argon ion laser beam, which is also used as the light source for fluorometric detection. The electrokinetic property and electric repulsion between sample components and anionic groups on the polyacrylamide gel layer produce, trap, and concentrate anions within a few minutes at the interface of the cathodic side of the gel layer. This method displays concentration factors as high as 10 (5). The availability of ionic preconcentrator was demonstrated by applying sensitive analysis of oligosaccharides labeled with 8-aminopyrene-1,3,6-trisulfonate and some glycoproteins labeled with fluorescein isothiocyanate under various buffer systems.

Measurement of cell migration in response to an evolving radial chemokine gradient triggered by a microvalve

We describe a novel chemotaxis assay based on the microvalve-actuated release of a chemoattractant from a cell-free microchamber into a cell-containing microchamber. The microvalve chemotaxis device (microVCD) was placed on the stage of a conventional inverted microscope to obtain time-lapse micrographs of neutrophils migrating in a radially-symmetric evolving gradient of the chemotactic factor CXCL8/Interleukin-8. A fluorescent tracer was added to the CXCL8 solution to visualize the evolution of the gradient profile, so that at each time point the cell positions could be assigned CXCL8 concentration values. Tracking of individual neutrophils for 90 minutes showed that (a) the neutrophil migratory response is, on average, radially directed towards the CXCL8 source; (b) significant non-radial displacements occur frequently; and (c) there is considerable heterogeneity in the migration speeds and directions amongst the neutrophil population. A custom-made imaging analysis tool was used to extract measurements of migratory behavior such as speed, velocity along the gradient's radial axis, and the cosine of the turning angle as a function of CXCL8 concentration. The microVCD can be easily adapted to study the migratory behavior of cultured cells other than neutrophils.