Fabrication of rubber gel as oil absorbent by using water as porosity agent for oil removal

An overview of cellulose aerogels and foams for oil sorption: Preparation, modification, and potential of 3D printing

Sorption is one of the most efficient methods to remediate the increasing oil spill incidents, but the currently available absorbents are inadequate to tackle such a global threat. Recently, numerous researchers have attempted to develop sustainable oil sorbents. Cellulose aerogels and foams, a type of lightweight porous material with excellent sorption performance, are one of the most promising candidates. Significant progress has been made in the past decade towards the development of cellulose porous materials as effective oil sorbents, with improvements in their oil sorption capacity, reusability, and enhanced multifunctionality, indicating their potential for oil spill remediation. This article reviews recent reports and provides a comprehensive overview of the preparation and modification strategies for cellulose porous materials, with a specific emphasis on their oil sorption performance and structure control. We also focus on the burgeoning 3D printing technology within this field, summarizing the latest advances with a discussion of the potential for using 3D printing to customize and optimize the structure of cellulose porous materials. Lastly, this review addresses current limitations and outlines future directions for development.

A Silica–Lignin Hybrid Filler in a Natural Rubber Foam Composite as a Green Oil Spill Absorbent

Oil spills in the marine environment are a rising concern due to their adverse impacts on living creatures and the environment. Hence, remediation methods have been used to remove the oil from the contaminated water. A sorbent material is considered the best method for oil spill absorption. However, commonly used commercial sorbents are made from nonrenewable and nonenvironmentally friendly materials. In this research, natural rubber foam (NRF) was used as a sorbent material with the addition of a filler, i.e., silica and a silica–lignin hybrid, to increase its oil sorption capacity and reusability. The silica and silica–lignin hybrid were extracted from rice husk waste by means of the precipitation method. The silica–lignin hybrid-filled NRF exhibited excellent hydrophobicity, with a water contact angle of 133°, and had more stable reusability compared to unfilled NRF and silica-filled NRF. In addition, the optimum oil absorption capacity of silica–lignin hybrid-filled NRF was 1.36 g g⁻¹. Overall, the results showed that silica–lignin hybrid-filled NRF has the potential to be developed as a green oil absorbent material and is promising in terms of economic and environmental aspects.

Improving the efficiency of post-digestion method in extracting microplastics from gastrointestinal tract and gills of fish

Post-digestion treatment is an important step during sample preparation to facilitate the removal of undigested materials for better detection of ingested microplastics. Sieving, density separation with zinc chloride solution (ZnCl₂), and oil extraction protocol (OEP) have been introduced in separating microplastics from sediments. The clean-up methods are rarely highlighted in previous studies, especially in the separation of microplastics from marine biota. Thus, this study proposed and compared the suitability of three techniques, which can reduce the number of undigested particles from the digestate of GIT and gills. Our result has shown excellent removal of non-plastics materials and reduces the coloration of filter paper in all treated samples. Both sieving and density separation achieved optimum post-digestion efficiencies of >95% for both GIT and gill samples, which former showed no effect on polymer integrity. Additionally, high recovery rate was obtained for the larger size microplastics (>500 μm) with approximately 97.7% (GIT) and 95.7% (gill), respectively. Exposure to the ZnCl₂ solution led to a significant loss of smaller size PET and changed the absorption spectrums of all tested polymers. Particle morphology determined by SEM revealed such exposure eroded the surface of PET fragments and elemental analysis has shown detectable peaks of zinc and chlorine appeared. Low microplastics recoveries were achieved through OPE and residue of oil was observed from the infrared spectrum of all tested polymer. The findings demonstrate sieving with size fractioning can provide exceptional removal of non-plastics materials from the digestate of GIT and gill samples.