Cellular transduction gradients via vapor-deposited polymer coatings

Novel insights into nanoscale surface displacement detection in polystyrene thin films using photothermal mirror- and atomic force microscopy-mid-IR spectroscopy

Photothermal spectroscopy techniques operating at single wavelengths in the vis-NIR range have been widely used to measure optical absorption and thermal characteristics of materials owing to their high sensitivity. We introduced photothermal mirror spectroscopy employing a highly tunable mid-IR pump laser (PTM-IR) for the chemical analysis of thin film polystyrene samples on IR transparent calcium fluoride substrates. PTM-IR spectroscopy surpasses conventional PTM spectroscopy as it provides chemical specificity through molecule-specific absorption via the detection of the magnitude of the PTM signal as a function of the excitation wavelength. We compared the obtained spectra with those measured using atomic force microscopy-infrared spectroscopy (AFM-IR), an already well-established photothermal technique also operating in the mid-IR range, and standard Fourier-transform infrared (FT-IR) spectroscopy. Numerical simulations using finite element analysis were employed to estimate the expected increase in temperature and surface deformation induced by the laser pulse train in each photothermal technique. Excellent agreement was obtained across the studied techniques in terms of qualitative mid-IR spectra and thickness determination.

Hydrolysis of Poly(fluoroacrylate) Thin Films Synthesized from the Vapor Phase

The post-synthesis surface reaction of vapor-deposited polymer thin films is a promising technique in engineering heterogeneous surface chemistry. Because the existing research has neglected marginally reactive precursor films in preference of their highly reactive counterparts, our knowledge of kinetics and loss of film integrity during the reaction are limited. To address these limitations, we characterize hydrolysis of two fluoroacrylates, poly(1H,1H,2H,2H-perfluorooctyl acrylate) (pPFOA) and poly(2,2,3,4,4,4-hexafluorobutyl acrylate) (pHFBA), with sodium hydroxide using X-ray photoelectron spectroscopy. Without crosslinking with di(ethylene glycol)divinyl ether (DEGDVE) and grafting with trichlorovinyl silane, the films degrade rapidly during hydrolysis. An SN2 mechanism describes hydrolysis well, with rate constants of 0.0029 ± 0.0004 and 0.011 ± 0.001 L mol-1s-1 at 30 °C for p(PFOA-co-DEGDVE) and p(HFBA-co-DEGDVE), respectively. Our detailed study of hydrolysis kinetics of marginally reactive fluoroacrylates demonstrates the full capability and limitations of the post-synthesis reaction. Importantly, copolymers are characterized using a density correction new to polymer chemical vapor deposition.

Tooth-Supporting Hard Tissue Regeneration Using Biopolymeric Material Fabrication Strategies

The mineralized tissues (alveolar bone and cementum) are the major components of periodontal tissues and play a critical role to anchor periodontal ligament (PDL) to tooth-root surfaces. The integrated multiple tissues could generate biological or physiological responses to transmitted biomechanical forces by mastication or occlusion. However, due to periodontitis or traumatic injuries, affect destruction or progressive damage of periodontal hard tissues including PDL could be affected and consequently lead to tooth loss. Conventional tissue engineering approaches have been developed to regenerate or repair periodontium but, engineered periodontal tissue formation is still challenging because there are still limitations to control spatial compartmentalization for individual tissues and provide optimal 3D constructs for tooth-supporting tissue regeneration and maturation. Here, we present the recently developed strategies to induce osteogenesis and cementogenesis by the fabrication of 3D architectures or the chemical modifications of biopolymeric materials. These techniques in tooth-supporting hard tissue engineering are highly promising to promote the periodontal regeneration and advance the interfacial tissue formation for tissue integrations of PDL fibrous connective tissue bundles (alveolar bone-to-PDL or PDL-to-cementum) for functioning restorations of the periodontal complex.

Vapor-deposited functional polymer thin films in biological applications

Functional polymer coatings have become ubiquitous in biological applications, ranging from biomaterials and drug delivery to manufacturing-scale separation of biomolecules using functional membranes. Recent advances in the technology of chemical vapor deposition (CVD) have enabled precise control of the polymer chemistry, coating thickness, and conformality. That comprehensive control of surface properties has been used to elicit desirable interactions at the interface between synthetic materials and living organisms, making vapor-deposited functional polymers uniquely suitable for biological applications. This review captures the recent technological development in vapor-deposited functional polymer coatings, highlighting their biological applications, including membrane-based bio-separations, biosensing and bio-MEMS, drug delivery, and tissue engineering. The conformal nature of vapor-deposited coatings ensures uniform coverage over micro- and nano-structured surfaces, allowing the independent optimization of surface and bulk properties. The substrate-independence of CVD techniques enables facile transfer of surface characteristics among different applications. The vapor-deposited functional polymer thin films tend to be biocompatible because they are free of remnant toxic solvents and precursor molecules, potentially lowering the barrier to clinical success.

Scaffolding polymeric biomaterials: Are naturally occurring biological macromolecules more appropriate for tissue engineering?

Nowadays, tissue and organ failures resulted from injury, aging accounts, diseases or other type of damages is one of the most important health problems with an increasing incidence worldwide. Current treatments have limitations including, low graft efficiency, shortage of donor organs, as well as immunological problems. In this context, tissue engineering (TE) was introduced as a novel and versatile approach for restoring tissue/organ function using living cells, scaffold and bioactive (macro-)molecules. Among these, scaffold as a three-dimensional (3D) support material, provide physical and chemical cues for seeding cells and has an essential role in cell missions. Among the wide verity of scaffolding materials, natural or synthetic biopolymers are the most commonly biomaterials mainly due to their unique physicochemical and biological features. In this context, naturally occurring biological macromolecules are particular of interest owing to their low immunogenicity, excellent biocompatibility and cytocompatibility, as well as antigenicity that qualified them as popular choices for scaffolding applications. In this review, we highlighted the potentials of natural and synthetic polymers as scaffolding materials. The properties, advantages, and disadvantages of both polymer types as well as the current status, challenges, and recent progresses regarding the application of them as scaffolding biomaterials are also discussed.

Micropatterned Scaffolds with Immobilized Growth Factor Genes Regenerate Bone and Periodontal Ligament-Like Tissues

Periodontal disease destroys supporting structures of teeth. However, tissue engineering strategies offer potential to enhance regeneration. Here, the strategies of patterned topography, spatiotemporally controlled growth factor gene delivery, and cell-based therapy to repair bone-periodontal ligament (PDL) interfaces are combined. Micropatterned scaffolds are fabricated for the ligament regions using polycaprolactone (PCL)/polylactic-co-glycolic acid and combined with amorphous PCL scaffolds for the bone region. Scaffolds are modified using chemical vapor deposition, followed by spatially controlled immobilization of vectors encoding either platelet-derived growth factor-BB or bone morphogenetic protein-7, respectively. The scaffolds are seeded with human cells and delivered to large alveolar bone defects in athymic rats. The effects of dual and single gene delivery with and without micropatterning are assessed after 3, 6, and 9 weeks. Gene delivery results in greater bone formation at three weeks. Micropatterning results in regenerated ligamentous tissues similar to native PDL. The combination results in more mature expression of collagen III and periostin, and with elastic moduli of regenerated tissues that are statistically indistinguishable from those of native tissue, while controls are less stiff than native tissues. Thus, controlled scaffold microtopography combined with localized growth factor gene delivery improves the regeneration of periodontal bone-PDL interfaces.

Micro- and nano-surface structures based on vapor-deposited polymers

Vapor-deposition processes and the resulting thin polymer films provide consistent coatings that decouple the underlying substrate surface properties and can be applied for surface modification regardless of the substrate material and geometry. Here, various ways to structure these vapor-deposited polymer thin films are described. Well-established and available photolithography and soft lithography techniques are widely performed for the creation of surface patterns and microstructures on coated substrates. However, because of the requirements for applying a photomask or an elastomeric stamp, these techniques are mostly limited to flat substrates. Attempts are also conducted to produce patterned structures on non-flat surfaces with various maskless methods such as light-directed patterning and direct-writing approaches. The limitations for patterning on non-flat surfaces are resolution and cost. With the requirement of chemical control and/or precise accessibility to the linkage with functional molecules, chemically and topographically defined interfaces have recently attracted considerable attention. The multifunctional, gradient, and/or synergistic activities of using such interfaces are also discussed. Finally, an emerging discovery of selective deposition of polymer coatings and the bottom-up patterning approach by using the selective deposition technology is demonstrated.

Multigrowth Factor Delivery via Immobilization of Gene Therapy Vectors

Molecules can be immobilized onto biomaterials by a chemical vapor deposition (CVD) coating strategy. Pentafluorophenolester groups react with amine side chains on antibodies, which can selectively immobilize adenoviral vectors for gene delivery of growth factors. These vectors can produce functional proteins within defined regions of biomaterials to produce customizable structures for targeted tissue regeneration.

Current Trends and Challenges in Biointerfaces Science and Engineering

The cellular microenvironment is extremely complex, and a plethora of materials and methods have been employed to mimic its properties in vitro. In particular, scientists and engineers have taken an interdisciplinary approach in their creation of synthetic biointerfaces that replicate chemical and physical aspects of the cellular microenvironment. Here the focus is on the use of synthetic materials or a combination of synthetic and biological ligands to recapitulate the defined surface chemistries, microstructure, and function of the cellular microenvironment for a myriad of biomedical applications. Specifically, strategies for altering the surface of these environments using self-assembled monolayers, polymer coatings, and their combination with patterned biological ligands are explored. Furthermore, methods for augmenting an important physical property of the cellular microenvironment, topography, are highlighted, and the advantages and disadvantages of these approaches are discussed. Finally, the progress of materials for prolonged stem cell culture, a key component in the translation of stem cell therapeutics for clinical use, is featured.

Tunable coverage of immobilized biomolecules for biofunctional interface design

Tunable biological responses can be controlled by the modifications of the density of the underlying chemical motifs and the density of the biomolecules immobilized.

Co-immobilization of biomolecules on ultrathin reactive chemical vapor deposition coatings using multiple click chemistry strategies

Immobilization of biomolecules, such as proteins or sugars, is a key issue in biotechnology because it enables the understanding of cellular behavior in more biological relevant environment. Here, poly(4-ethynyl-p-xylylene-co-p-xylylene) coatings have been fabricated by chemical vapor deposition (CVD) polymerization in order to bind bioactive molecules onto the surface of the material. The control of the thickness of the CVD films has been achieved by tuning the amount of precursor used for deposition. Copper-catalyzed Huisgen cycloaddition has then been performed via microcontact printing to immobilize various biomolecules on the reactive coatings. The selectivity of this click chemistry reaction has been confirmed by spatially controlled conjugation of fluorescent sugar recognizing molecules (lectins) as well as cell adhesion onto the peptide pattern. In addition, a microstructured coating that may undergo multiple click chemistry reactions has been developed by two sequential CVD steps. Poly(4-ethynyl-p-xylylene-co-p-xylylene) and poly(4-formyl-p-xylylene-co-p-xylylene) have been patterned via vapor-assisted micropatterning in replica structures (VAMPIR). A combination of Huisgen cycloaddition and carbonyl-hydrazide coupling was used to spatially direct the immobilization of sugars on a patterned substrate. This work opens new perspectives in tailoring microstructured, multireactive interfaces that can be decorated via bio-orthogonal chemistry for use as mimicking the biological environment of cells.

Vapor-based tri-functional coatings

The tri-functional coating synthesized via CVD copolymerization is comprised of distinguished anchoring sites of acetylene, maleimide, and ketone that can synergically undergo specific conjugation reactions to render surfaces with distinct biological functions, simultaneously. In addition, these tri-functional coatings can be fabricated in a micro-structured fashion on non-conventional surfaces.

Vapor-deposited parylene photoresist: a multipotent approach toward chemically and topographically defined biointerfaces

Poly(4-benzoyl-p-xylylene-co-p-xylylene), a biologically compatible photoreactive polymer belonging to the parylene family, can be deposited using a chemical vapor deposition (CVD) polymerization process on a wide range of substrates. This study discovered that the solvent stability of poly(4-benzoyl-p-xylylene-co-p-xylylene) in acetone is significantly increased when exposed to approximately 365 nm of UV irradiation, because of the cross-linking of benzophenone side chains with adjacent molecules. This discovery makes the photodefinable polymer a powerful tool for use as a negative photoresist for surface microstructuring and biointerface engineering purposes. The polymer is extensively characterized using infrared reflection adsorption spectroscopy (IRRAS), scanning electron microscopy (SEM), and imaging ellipsometry. Furthermore, the vapor-based polymer coating process provides access to substrates with unconventional and complex three-dimensional (3D) geometries, as compared to conventional spin-coated resists that are limited to flat 2D assemblies. Moreover, this photoresist technology is seamlessly integrated with other functionalized parylenes including aldehyde-, acetylene-, and amine-functionalized parylenes to create unique surface microstructures that are chemically and topographically defined. The photopatterning and immobilization protocols described in this paper represent an approach that avoids contact between harmful substances (such as solvents and irradiations) and sensitive biomolecules. Finally, multiple biomolecules on planar substrates, as well as on unconventional 3D substrates (e.g., stents), are presented.

Growth factor delivery: how surface interactions modulate release in vitro and in vivo

Biomaterial scaffolds have been extensively used to deliver growth factors to induce new bone formation. The pharmacokinetics of growth factor delivery has been a critical regulator of their clinical success. This review will focus on the surface interactions that control the non-covalent incorporation of growth factors into scaffolds and the mechanisms that control growth factor release from clinically relevant biomaterials. We will focus on the delivery of recombinant human bone morphogenetic protein-2 from materials currently used in the clinical practice, but also suggest how general mechanisms that control growth factor incorporation and release delineated with this growth factor could extend to other systems. A better understanding of the changing mechanisms that control growth factor release during the different stages of preclinical development could instruct the development of future scaffolds for currently untreatable injuries and diseases.

Immobilized streptavidin gradients as bioconjugation platforms

Surface density gradients of streptavidin (SAV) were created on solid surfaces and demonstrated functionality as a bioconjugation platform. The surface density of immobilized streptavidin steadily increased in one dimension from 0 to 235 ng cm(-2) over a distance of 10 mm. The density of coupled protein was controlled by its immobilization onto a polymer surface bearing a gradient of aldehyde group density, onto which SAV was covalently linked using spontaneous imine bond formation between surface aldehyde functional groups and primary amine groups on the protein. As a control, human serum albumin was immobilized in the same manner. The gradient density of aldehyde groups was created using a method of simultaneous plasma copolymerization of ethanol and propionaldehyde. Control over the surface density of aldehyde groups was achieved by manipulating the flow rates of these vapors while moving a mask across substrates during plasma discharge. Immobilized SAV was able to bind biotinylated probes, indicating that the protein retained its functionality after being immobilized. This plasma polymerization technique conveniently allows virtually any substrate to be equipped with tunable protein gradients and provides a widely applicable method for bioconjugation to study effects arising from controllable surface densities of proteins.