Optimal conditions for olive mill wastewater treatment using ultrasound and advanced oxidation processes

Olive mill wastewater treatment strategies to obtain quality water for irrigation: A review

The olive mill industry is a relevant sector in the economy of Mediterranean countries, while it involves high consumption of water and the production of effluents with high environmental impact. The efficient treatment of olive mill wastewater (OMW) is of high relevance, particularly for these countries. Climate changes are leading to increasing periods of droughts, and water recovery from polluted streams is essential to ensure the sustainability of this scarce resource. A combination of various technologies involving physical, chemical, and biological processes has been developed for OMW treatment. However, the treatments studied have limitations such as the operation costs, difficulty of industrial scale-up, and the fact that the vast majority do not lead to suitable treated water for discharge/reuse. As such, it is urgent to develop a solution capable of efficiently treating this effluent, overcoming the disadvantages of existing processes to convert OMW from a serious environmental problem into a valuable source of water and nutrients. In this review, several studies based on the OMW treatment are critically discussed, from conventional approaches such as the physical (e.g. centrifugation, filtration, and adsorption) and biological (anaerobic digestion and anaerobic co-digestion) processes, to the most recent technologies such as advanced membrane filtration, advanced oxidation processes (AOPs) and sulfate radical based AOPs (SR-AOPs). Due to the complexity of the effluent, OMW cannot be efficiently treated by a single process, requiring a sequence of technologies before reaching the required characteristics for discharge into water courses or use in crop irrigation. Reviewing the published results in this matter, it seems that the sequence of processes encompassing ozonation, anaerobic digestion, and SR-AOPs could be the ideal combination for this purpose. However, membrane technologies may be necessary in the final stage of treatment so that the effluent meets legal discharge or irrigation limits.

Utilizing Chlorella vulgaris algae as an eco-friendly coagulant for efficient removal of polyethylene microplastics from aquatic environments

Polyethylene (PE) microplastics (MPs) are small particles of plastic made from polyethylene, which is a commonly used type of plastic. These microplastics can be found in water sources, such as rivers, lakes, and oceans. They are typically less than 5 mm in size. Chlorella vulgaris (C. vulgaris) is an excellent, simple and inexpensive biocoagulant that can effectively remove a wide range of pollutants through the coagulation and flocculation mechanism. In this study, C. vulgaris algae were used to remove PE MPs. The experiments were designed using the Behnken Box model. The evaluated parameters were the initial PE concentration (100-400 mg/L), the C. vulgaris dose (50-200), and the pH (4-10). The findings showed that increasing the concentration of polyethylene had a positive effect on the efficiency of removal. In addition, the dose of C. vulgaris and pH parameters were inversely and directly related to removal efficiency, respectively. The highest removal efficiency was observed under alkaline conditions. Overall, the maximum PE removal efficiency was 84 % when the concentration of PE was 250 mg/L, the dose of C. vulgaris was 50 mg/L, and the pH was 10. It can be concluded that algae can be used as an environmentally friendly coagulant for effectively removing MPs from aquatic environments.

Integrating of electrocoagulation process with submerged membrane bioreactor for wastewater treatment under low voltage gradients

Treating and reusing wastewater has become an essential aspect of water management worldwide. However, the increase in emerging pollutants such as polycyclic aromatic hydrocarbons (PAHs), which are presented in wastewater from various sources like industry, roads, and household waste, makes their removal difficult due to their low concentration, stability, and ability to combine with other organic substances. Therefore, treating a low load of wastewater is an attractive option. The study aimed to address membrane fouling in the submerged membrane bioreactor (SMBR) used for wastewater treatment. An aluminum electrocoagulation (EC) device was combined with SMBR as a pre-treatment to reduce fouling. The EC-SMBR process was compared with a conventional SMBR without EC, fed with real grey water. To prevent impeding biological growth, low voltage gradients were utilized in the EC deviceThe comparison was conducted over 60 days with constant transmembrane pressure and infinite solid retention time (SRT). In phase I, when the EC device was operated at a low voltage gradient (0.64 V/cm), no significant improvement in the pollutants removal was observed in terms of color, turbidity, and chemical oxygen demand (COD). Nevertheless, during phase II, a voltage gradient of 1.26 V/cm achieved up to 100%, 99.7%, 92%, 94.1%, and 96.5% removals in the EC-SMBR process in comparison with 95.1%, 95.4%, 85%, 91.7% and 74.2% removals in the SMBR process for turbidity, color, COD, ammonia nitrogen (NH3-N), total phosphorus (TP), respectively. SMBR showed better anionic surfactant (AS) removal than EC-SMBR. A voltage gradient of 0.64 V/cm in the EC unit significantly reduced fouling by 23.7%, while 1.26 V/cm showed inconsistent results. Accumulation of Al ions negatively affected membrane performance. Low voltage gradients in EC can control SMBR fouling if Al concentration is controlled. Future research should investigate EC-SMBR with constant membrane flux for large-scale applications, considering energy consumption and operating costs.

MXenes and MXene-based materials for removal of pharmaceutical compounds from wastewater: Critical review

The rapid increase in the global population and its ever-rising standards of living are imposing a huge burden on global resources. Apart from the rising energy needs, the demand for freshwater is correspondingly increasing. A population of around 3.8 billion people will face water scarcity by 2030, as per the reports of the World Water Council. This may be due to global climate change and the deficiency in the treatment of wastewater. Conventional wastewater treatment technologies fail to completely remove several emerging contaminants, especially those containing pharmaceutical compounds. Hence, leading to an increase in the concentration of harmful chemicals in the human food chain and the proliferation of several diseases. MXenes are transition metal carbide/nitride ceramics that primarily structure the leading 2D material group. MXenes act as novel nanomaterials for wastewater treatment due to their high surface area, excellent adsorption properties, and unique physicochemical properties, such as high electrical conductivity and hydrophilicity. MXenes are highly hydrophilic and covered with active functional groups (i.e., hydroxyl, oxygen, fluorine, etc.), which makes them efficient adsorbents for a wide range of species and promising candidates for environmental remediation and water treatment. This work concludes that the scaling up process of MXene-based materials for water treatment is currently of high cost. The up-to-date applications are still limited because MXenes are currently produced mainly in the laboratory with limited yield. It is recommended to direct research efforts towards lower synthesis cost procedures coupled with the use of more environmentally friendly materials to avoid secondary contamination.

Occurrence of per- and polyfluoroalkyl substances in aquatic environments and their removal by advanced oxidation processes

Per- and polyfluoroalkyl substances (PFAS), one of the main categories of emerging contaminants, are a family of fluorinated organic compounds of anthropogenic origin. PFAS can endanger the environment and human health because of their wide application in industries, long-term persistence, unique properties, and bioaccumulation potential. This study sought to explain the accumulation of different PFAS in water bodies. In aquatic environments, PFAS concentrations range extensively from <0.03 (groundwater; Melbourne, Australia) to 51,000 ng/L (Groundwater, Sweden). Additionally, bioaccumulation of PFAS in fish and water biota has been stated to range from 0.2 (Burbot, Lake Vättern, Sweden) to 13,900 ng/g (Bluegill samples, U.S.). Recently, studies have focused on PFAS removal from aqueous solutions; one promising technique is advanced oxidation processes (AOPs), including microwaves, ultrasound, ozonation, photocatalysis, UV, electrochemical oxidation, the Fenton process, and hydrogen peroxide-based and sulfate radical-based systems. The removal efficiency of PFAS ranges from 3% (for MW) to 100% for UV/sulfate radical as a hybrid reactor. Therefore, a hybrid reactor can be used to efficiently degrade and remove PFAS. Developing novel, efficient, cost-effective, and sustainable AOPs for PFAS degradation in water treatment systems is a critical area of research.

An optimized sono-heterogeneous Fenton degradation of olive-oil mill wastewater organic matter by new magnetic glutarlaldehyde-crosslinked developed cellulose

The present study highlights the olive mill wastewater (OMW) treatment characteristics through a sono-heterogeneous Fenton process using new designed [GTA-(PDA-g-DAC) @Fe₃O₄] and characterized by Fourier transform infrared (FTIR) spectroscopy, X-ray diffraction (XRD), thermogravimetric analysis (TGA), magnetic properties measurements, and point of zero charge (pH pzc) analysis. A preliminary removal study showed significant degradation efficiency (75%) occurred combining the magnetic synthesized catalyst [GTA-(PDA-g-DAC)@Fe3O4] ([catalyst] = 2 g/L) with US /H₂O₂ and maintaining 500WL^-1 ultrasonic power (US). The values obtained by US only were (13%), H₂O₂/US (18%), US/Fe₃O₄ (28%), and US /Fe₃O₄/H₂O₂(35%). The catalytic findings have shown that [GTA-(PDA-g-DAC)@Fe₃O₄] exhibited good properties for OMW compound's degradation. The sonocatalytic process coupling and extra oxidant addition resulted in the degradation substantial levels. For instance, the concomitant effect of degradation optimized parameters; H₂O₂ 10 mM, [GTA-(PDA-g-DAC) @Fe₃O₄] nanocomposites 2.5 g/L, at pH 3, and T 35 °C for 70 min resulted in an almost complete mineralization of aqueous OMW solution followed by a significant decolorization. Oxidation results exhibited efficient degradation rates in total phenolic compounds (TPC), total amino compounds (TAC), and chemical oxygen demand (COD) oxidation rate were 89.88, 92.75, and 95.66 respectively following the optimized sono-heterogeneous catalytic Fenton process. The prepared magnetic catalyst exhibited a good stability during repeated cycles. The gathered findings gave the evidence that sono-heterogeneous catalytic Fenton process is a promising treatment technology for OMW effluents.

Phenolic Compounds Removal from Olive Mill Wastewater Using the Composite of Activated Carbon and Copper-Based Metal-Organic Framework

As the industry of olive oil continues to grow, the management of olive mill wastewater (OMW) by-products has become an area of great interest. While many strategies for processing OMW have been established, more studies are still required to find an effective adsorbent for total phenolic content uptake. Here, we present a composite of a Cu 1,4-benzene dicarboxylate metal-organic framework (Cu (BDC) MOF) and granular activated carbon (GAC) as an adsorbent for total phenolic content removal from OMW. Experimental results demonstrated that the maximum adsorption capacity was 20 mg/g of total phenolic content (TPC) after 4 h. using 2% wt/wt of GAC/Cu (BDC) MOF composite to OMW at optimum conditions (pH of 4.0 and 25 °C). The adsorption of phenolic content onto the GAC/Cu (BDC) MOF composite was described by the Freundlich adsorption and pseudo-second-order reaction. The adsorption reaction was found to be spontaneous and endothermic at 298 K where ΔS° and ΔH° were found to be 0.105 KJ/mol and 25.7 kJ/mol, respectively. While ΔGº value was -5.74 (kJ/mol). The results of this study provide a potential solution for the local and worldwide olive oil industry.

A data-driven modeling approach for the sustainable remediation of persistent arsenic (As) groundwater contamination in a fractured rock aquifer through a groundwater recirculation well (IEG-GCW®)

Persistent arsenic (As) pollution sources from anthropogenic activities pose a serious threat to groundwater quality. This work aims to illustrate the application of an innovative remediation technology to remove As from a heavily contaminated fractured aquifer at a historically polluted industrial site. Groundwater circulation well (GCW) technology was tested to significantly increase and accelerate the mobilization and removal of As in the source area. The GCW extracts and re-injects groundwater at different depths of a vertical circulation well. By pumping out and reinjecting in different screen sections of the well, the resulting vertical hydraulic gradients create recirculation cells and affect and mobilize trapped contaminants that cannot be influenced by traditional pumping systems. The first 45-m deep IEG-GCW® system was installed in 2020, equipped with 4 screen sections at different depths and with an above-ground As removal system by oxidation and filtration on Macrolite (Enki). A geomodeling approach supports both remediation and multi-source data interpretation. The first months of operation demonstrate the hydraulic effectiveness of the IEG-GCW® system in the fractured rock aquifer and the ability to significantly enhance As removal compared to conventional pumping wells currently feeding a centralized treatment system. The recirculation flow rate amounts to about 2 m³/h. Water pumped and treated by the GCW system is reintroduced with As concentrations reduced by an average of 20%-60%. During the pilot test, the recirculating system removed 23 kg As whilst the entire central pump-and-treat (P&T) system removed 129 kg, although it treated 100 times more water volume. The P&T plant removed 259 mg As per m³ of pumped and treated groundwater while the GCW removed 4814 mg As per m³ of the treated groundwater. The results offer the opportunity for a more environmentally sustainable remediation approach by actively attacking the contamination source rather than containing the plume.

Evaluation of scrap metallic waste electrode materials for the application in electrocoagulation treatment of wastewater

The constant need for sacrificial electrodes is one of the limitations of applying the EC in wastewater treatment. Accordingly, this study proposes a sustainable alternative in reusing scrap metallic wastes as electrode materials. Four different types of metallic wastes (beverage cans, used aluminum (Al) foil, scrap iron, and scrap mild steel) are proposed as sacrificial electrodes for grey water (GW) treatment using the EC technique. At electrical current densities (CD) ranging between 5 and 20 mA/cm², the treatment performance was evaluated for a reaction time of 10 min in terms of the removal efficiency of some key parameters such as color, turbidity, chemical oxygen demand (COD), and electrical conductivity, energy and material consumption, and metal contamination of GW from electrodes. The results demonstrated that using metallic wastes as sacrificial electrodes can achieve a considerable reduction in color, turbidity, COD, and electric conductivity of about 97.2%, 99%, 88%, and 89%, respectively. However, their reuse as electrodes revealed some important concerns. Al foil undergoes quick and substantial perforation and loss of surface area during electrolysis. The scrap iron and scrap mild steel were found to cause metal contamination by increasing Fe ions in the treated GW. Generally, metal scrap wastes can serve effectively as alternative sustainable electrodes. However, further research is recommended regarding the operating costs, which are considered crucial aspects of the EC process in terms of energy consumption and the most efficient method of fabricating the metallic wastes into a form suitable for reuse in the EC technique.

Microplastics in sewage sludge: Distribution, toxicity, identification methods, and engineered technologies

Microplastic pollution is becoming a global challenge due to its long-term accumulation in the environment, causing adverse effects on human health and the ecosystem. Sludge discharged from wastewater treatment plants (WWTPs) plays a critical role as a carrier and primary source of environmental microplastic contamination. A significantly average microplastic variation between 1000 and 301,400 particles kg^-1 has been reported in the sludge samples. In recent years, advanced technologies have been successfully applied to address this issue, including adsorption, advanced oxidation processes (AOPs), and membrane bioreactors (MBRs). Adsorption technologies are essential to utilizing novel adsorbents (e.g., biochar, graphene, zeolites) for effectively removing MPs. Especially, the removal efficiency of polymer microspheres from an aqueous solution by Mg/Zn modified magnetic biochars (Mg/Zn-MBC) was obtained at more than 95%. Also, advanced oxidation processes (AOPs) are widely applied to degrade microplastic contaminants, in which photocatalytic by semiconductors (e.g., TiO₂ and ZnO) is a highly suitable approach to promote the degradation reactions owing to strongly hydroxyl radicals (OH*). Biological degradation-aided microorganisms (e.g., bacterial and fungal strains) have been reported to be suitable for removing microplastics. Yet, it was affected by biotic and abiotic factors of the environmental conditions (e.g., pH, light, temperature, moisture, bio-surfactants, microorganisms, enzymes) as well as their polymer characteristics, i.e., molecular weight, functional groups, and crystallinity. Notably, membrane bioreactors (MBRs) showed the highest efficiency in removing up to 99% microplastic particles and minimizing their contamination in sewage sludge. Further, MBRs illustrate the suitability for treating high-strength compounds, e.g., polymer debris and microplastic fibers from complex industrial wastewater. Finally, this study provided a comprehensive understanding of potential adverse risks, transportation pathways, and removal mechanisms of microplastic, which full-filled the knowledge gaps in this field.

Sonophotocatalytic degradation of malachite green in aqueous solution using six competitive metal oxides as a benchmark

A comparison study examines six different metal oxides (CuO, ZnO, Fe3O4, Co3O4, NiO, and α-MnO2) for the degradation of malachite green dye using four distinct processes. These processes are as follows: sonocatalysis (US/metal oxide), sonocatalysis under ultra-violet irradiation (US/metal oxide/UV), sonocatalysis in the presence of hydrogen peroxide (US/metal oxide/H2O2), and a combination of all these processes (US/metal oxide/UV/H2O2). The effective operating parameters, such as the dosage of metal oxide nanoparticles (MONPs), the type of the process, and the metal oxides’ efficiency order, were studied. At the same reaction conditions, the sonophotocatalytic is the best process for all six MOsNPs, CuO was the better metal oxide than other MOsNPs, and at the sonocatalysis process, ZnO was the best metal oxide in other processes. It was found that the metal oxide order for sonocatalytic process is CuO > α-MnO2 ≥ ZnO > NiO ≥ Fe3O4 ≥ Co3O4 within 15–45 min. The order of (US/metal oxide/UV) process is ZnO ≥ NiO ≥ α-MnO2 > Fe3O4 ≥ CuO ≥ Co3O4 within 5–40 min. The order of (US/ MOsNPs/ H2O2) process is ZnO ≥ CuO ≥ α-MnO2 ≥ NiO > Co3O4 > Fe3O4 within 5–20 min. The maximum removal efficiency order of the sonophotocatalytic process is ZnO ≥ CuO > α-MnO2 > NiO > Fe3O4 ≥ Co3O4 within 2–8 min. The four processes degradation efficiency was in the order US/MOsNPs ˂ US/MOsNPs/UV ˂ US/MOsNPs/H2O2 ˂ (UV/Ultrasonic/MOsNPs/H2O2). Complete degradation of MG was obtained at 0.05 g/L MONPs and 1 mM of H2O2 using 296 W/L ultrasonic power and 15 W ultra-violet lamp (UV-C) within a reaction time of 8 min according to the MOsNPs type at the same sonophotocatalytic/H2O2 reaction conditions. The US/metal oxide/UV/H2O2 process is inexpensive, highly reusable, and efficient for degrading dyes in colored wastewater.

Graphical abstract

Advanced oxidation processes: Performance, advantages, and scale-up of emerging technologies

Advanced oxidation processes (AOPs) are promising technologies for partial or complete mineralization of contaminants of emerging concern by highly reactive hydroxyl, hydroperoxyl, superoxide, and sulphate radicals. Detailed investigations and reviews have been reported for conventional AOP systems that have been installed in full-scale wastewater treatment plants. However, recent efforts have focused on the peroxymonosulphate, persulphate, catalytic ozonation, ultrasonication and hydrodynamic cavitation, gamma radiation, electrochemical oxidation, modified Fenton, and plasma-assisted AOPs. This critical review presents the detailed mechanisms of emerging AOP technologies, their performance for treatment of contaminants of emerging concern, the relative advantages and disadvantages of each technology, and the remaining challenges to scale-up and implementation. Among the evaluated technologies, the modified electrochemical oxidation, gamma radiation, and plasma-assisted systems demonstrated the greatest potential for successful and sustainable implementation in wastewater treatment due to their environmental safety, compatibility, and efficient transformation of contaminants of emerging concern by a variety of reactive species. The other emerging AOP systems were also promising, but additional scale-up trials and a deeper understanding of their reaction kinetics in complex wastewater matrices are necessary to determine the technical and economic feasibility of full-scale processes.

Olive Mill Wastewater (OMW) Treatment Using Photocatalyst Media

A new nanophotocatalysts series of M2Zr2O7 (M = Mn, Cu, and Fe) and doped Fe2Zr2O7 systems were prepared via sol-gel using the pechini method, characterized, and tested in photocatalytic degradation of olive mill wastewater (OMW). The photocatalytic degradation of the prepared materials was evaluated by measuring total phenolic compounds (TPCs) using the Folin-Ciocalteu method for variable pH under a commercial LED lamp (45 W). The removal of TPCs was measured at different contact times ranging from 2 h to 6 days. X-ray diffraction (XRD) and transmission electron microscope (TEM) analysis approved the nano size of (5–17 nm) and quasi-spherical morphology of the prepared materials. ICP-OES analysis confirmed the XRD analysis and approved the structure of the prepared materials. Aggregation of the nanomaterials was observed using TEM imaging. Brunauer-Emmett-Teller (BET) analysis measured a 67 m2/g surface area for Fe2Zr2O7. Doping Fe with Mn increased the surface area to 173 m2/g and increased to 187 m2/g with a further increase of the Mn dopant. Increasing the Mn dopant concentration increased both surface area and photocatalytic degradation. The highest degradation of TPCs was observed for Mn2Zr2O7 around 70% at pH 10 and exposure time up to one day.

Thermophilic Dark Fermentation of Olive Mill Wastewater in Batch Reactors: Effect of pH and Organic Loading

In recent decades, olive oil consumption has almost tripled worldwide. Olive oil production is linked with the production of enormous amounts of olive mill wastewater, the main by-product derived from three-phase olive mills. Due to the environmental risks of olive mill wastewater disposal, the management and valorization of the specific waste stream is of great importance. This work focuses on the thermophilic dark fermentation of olive mill wastewater in batch reactors, targeting pH optimization and the organic loading effect. A series of experiments were performed, during which the organic load of the substrate remained at 40 g/L after dilution with tap water, and the pH was tested in the range of 4.5 to 7.5. The maximum yield in terms of produced hydrogen was obtained at pH 6.0, and the yields were 0.7 mol H2/mol glucose or 0.5 L H2/Lreactor. At the same conditions, a reduction of 62% of the waste’s phenols was achieved. However, concerning the effect of organic loading at the optimized pH value (6.0), a further increase in the organic load minimized the hydrogen production, and the overall process was strongly inhibited.

Olive mill wastewater phytoremediation employing economically important woody plants

In this study two plant species, Punica granatum L. and Myrtus communis L., have been tested as candidates for phytoremediation of olive mill wastewater (OMW) through recirculation in soil pilot units, according to the proposed patented technology by Santori and Cicalini [EP1216963 A. 26 Jun 2002]. Wastewater was treated in batches of low to high organics strength (COD: 2 700-45 700 mg/L) during summer months of two consecutive years. Dynamics of the most important wastewater parameters were investigated, and corresponding removal rates were estimated. During treatment of low organic load OMW, average removal rate of organics, phenolics, total nitrogen and total phosphorus were 0.68 g-COD/kg-soil d, 0.073 g-TPh/kg-soil d, 0.033 g-TN/kg-soil d and 0.0074 g-TP/kg-soil d respectively and plants proved to be tolerant to the OMW. During treatment of high organic load OMW removal rates were roughly 10-fold higher although phytotoxic symptoms were observed. Plants were found to contribute greatly to the OMW treatment process since organics removal rates in pilot units were found to be at least 10-fold higher than in wastewater treatment in non-vegetated soil. Plant species with high added value products such as pomegranate and myrtle trees were used in this study, improving the circular economy potential of the aforementioned technology. Moreover, its efficiency has been demonstrated by quantification of the overall removal rates of key constituents as well as the contribution of the plants in the OMW treatment.

Energy production from treatment of industrial wastewater and boron removal in aqueous solutions using microbial desalination cell

As a result of a much needed paradigm shift worldwide, treated saline water is being considered as a viable option for replacing freshwater resources in agricultural irrigation. Vastly produced geothermal brine in Turkey may pose a significant environmental risk due to its high ionic strength, specifically due to boron. Boron species, which are generally found uncharged in natural waters, are costly to remove using high-throughput membrane technologies such as reverse osmosis. Recent advances in bioelectrochemical systems (BES) has facilitated development of energetically self-sufficient wastewater treatment and desalination. In this study, removal of boron from synthetic solutions and real geothermal waters, along with simultaneous energy production, using the microbial desalination cell (MDC) were investigated. Optimization studies were conducted by varying boron concentrations (5, 10, and 20 mg L^-1), air flow rates (0, 1, and 2 L min^-1), electrode areas (18, 24, 36, and 72 cm²), catholyte solutions, and operating modes. Even though the highest concentration decrease was observed for 20 mg-B L^-1, 5 mg-B L^-1 concentration experiment gave the closest result to the 2.4 mg-B L^-1 limit value asserted by WHO. Effect of electrode surface area was proven to be significant on boron removal efficiency. Employing the optimum conditions acquired with synthetic solutions, boron and COD removal efficiencies from real geothermal brine were 44.3% and 90.6%, respectively. MDC, being in its early levels of technology readiness, produced promising desalination and energy production results in removal of boron from geothermal brine.

Biodegradable polymers and their nano-composites for the removal of endocrine-disrupting chemicals (EDCs) from wastewater: A review

Endocrine-disrupting chemicals (EDCs) target the endocrine system by interfering with the natural hormones in the body leading to adverse effects on human and animal health. These chemicals have been identified as major polluting agents in wastewater effluents. Pharmaceuticals, personal care products, industrial compounds, pesticides, dyes, and heavy metals are examples of substances that could be considered endocrine active chemicals. In humans, these chemicals could cause obesity, cancer, Alzheimer's disease, autism, reproductive abnormalities, and thyroid problems. While in wildlife, dysfunctional gene expression could lead to the feminization of some aquatic organisms, metabolic diseases, cardiovascular risk, and problems in the reproductive system as well as its levels of hatchability and vitellogenin. EDCs could be effectively removed from wastewater using advanced technologies such as reverse osmosis, membrane treatment, ozonation, advanced oxidation, filtration, and biodegradation. However, adsorption has been proposed as a more promising and sustainable method for water treatment than any other reported technique. Increased attention has been paid to biodegradable polymers and their nano-composites as promising adsorbents for the removal of EDCs from wastewater. These polymers could be either natural, synthetic, or a combination of both. This review presents a summary of the most relevant cases where natural and synthetic biodegradable polymers have been used for the successful removal of EDCs from wastewater. It demonstrates the effectiveness of these polymers as favorable adsorbents for novel wastewater treatment technologies. Hitherto, very limited work has been published on the use of both natural and synthetic biodegradable polymers to remove EDCs from wastewater, as most of the studies focused on the utilization of only one type, either natural or synthetic. Therefore, this review could pave the way for future exploration of biodegradable polymers as promising and sustainable adsorbents for the removal of various types of pollutants from wastewater.

Synthesis and Characterization of Carbon and Carbon-Nitrogen Doped Black TiO2 Nanomaterials and Their Application in Sonophotocatalytic Remediation of Treated Agro-Industrial Wastewater

The conventional open ponding system employed for palm oil mill agro-effluent (POME) treatment fails to lower the levels of organic pollutants to the mandatory standard discharge limits. In this work, carbon doped black TiO₂ (CB-TiO₂) and carbon-nitrogen co-doped black TiO₂ (CNB-TiO₂) were synthesized via glycerol assisted sol-gel techniques and employed for the remediation of treated palm oil mill effluent (TPOME). Both the samples were anatase phase, with a crystallite size of 11.09–22.18 nm, lower bandgap of 2.06–2.63 eV, superior visible light absorption ability, and a high surface area of 239.99–347.26 m²/g. The performance of CNB-TiO₂ was higher (51.48%) compared to only (45.72%) CB-TiO₂. Thus, the CNB-TiO₂ is employed in sonophotocatalytic reactions. Sonophotocatalytic process based on CNB-TiO₂, assisted by hydrogen peroxide (H₂O₂), and operated at an ultrasonication (US) frequency of 30 kHz and 40 W power under visible light irradiation proved to be the most efficient for chemical oxygen demand (COD) removal. More than 90% of COD was removed within 60 min of sonophotocatalytic reaction, producing the effluent with the COD concentration well below the stipulated permissible limit of 50 mg/L. The electrical energy required per order of magnitude was estimated to be only 177.59 kWh/m³, indicating extreme viability of the proposed process for the remediation of TPOME.

Understanding the effects of mineral water matrix on degradation of several pharmaceuticals by ultrasound: Influence of chemical structure and concentration of the pollutants

Degradation of seven relevant pharmaceuticals with different chemical structures and properties: acetaminophen (ACE), cloxacillin (CXL), diclofenac (DCF), naproxen (NPX), piroxicam (PXC), sulfacetamide (SAM) and cefadroxil (CDX), in distilled water and mineral water by ultrasound was studied herein. Firstly, proper conditions of frequency and acoustic power were determined based on the degradation ability of the system and the accumulation of sonogenerated hydrogen peroxide (24.4 W and 375 kHz were found as the suitable conditions for the sonochemical treatment of the pharmaceuticals). Under such conditions, the pharmaceuticals degradation order in distilled water was: PXC > DCF ~ NPX > CXL > ACE > SAM > CDX. In fact, the initial degradation rate showed a good correlation with the Log P parameter, most hydrophobic compounds were eliminated faster than the hydrophilic ones. Interestingly, in mineral water, the degradation of those hydrophilic compounds (i.e., ACE, SAM and CDX) was accelerated, which was attributed to the presence of bicarbonate ions. Afterwards, mineral water containing six different initial concentrations (i.e., 0.331, 0.662, 3.31, 16.55, 33.1, and 331 µM) of selected pharmaceuticals was sonicated, the lowest concentration (0.331 µM) always gave the highest degradation of the pollutants. This result highlights the great ability of the sonochemical process to treat bicarbonate-rich waters containing pollutants at trace levels, as pharmaceuticals. Finally, the addition of ferrous ions to the sonochemical system to generate a sono-Fenton process resulted in an acceleration of degradation in distilled water but not in mineral water. This was attributed to the scavenging of sonogenerated HO• by bicarbonate anion, which decreases H₂O₂ accumulation, thus limiting the Fenton reaction.

Covalent organic frameworks as robust materials for mitigation of environmental pollutants

Today, one of the main leading global problems is the presence of different pollutants in the environment. These pollutants not only affect human health but also overshadow the life of other creatures. Thus, pollutant treatment has become a challenging issue among the researchers and the scientific community. Different adsorbents and catalysts have been applied to the removal of pollutants. However, the associated limitations like poor chemical and physical stability, low surface area and low binding capacity revived researchers' attention to exploring alternative materials. Covalent organic frameworks (COFs) are versatile materials created based on the strong covalent interactions between blocked monomers. Unique features, including high specific surface area, high chemical-physical stability and crystallinity render COFs an intriguing sorbent and catalyst in treating pollutants. This review spotlights the applications of COFs as distinguished adsorbents to remove hazardous pollutants from the environment. At first, COFs and their properties as alternative materials were introduced. Then, different synthesis approaches of COFs and their advantages and disadvantages were discussed. Furthermore, the applications of COFs outlined to remove a wide variety of pollutants based on adsorption and degradation. Finally, the prospects of COFs for the treatment of pollutants were evaluated.

Efficient removal of phenol compounds from water environment using Ziziphus leaves adsorbent

Industrial processes generate toxic organic molecules that pollute environment water. Phenol and its derivative are classified among the major pollutant compounds found in water. They are naturally found in some industrial wastewater effluents. The removal of phenol compounds is therefore essential because they are responsible for severe organ damage if they exist above certain limits. In this study, ground Ziziphus leaves were utilized as adsorbents for phenolic compounds from synthetic wastewater samples. Several experiments were performed to study the effect of several conditions on the capacity of the Ziziphus leaves adsorbent, namely: the initial phenol concentration, the adsorbent concentration, temperature, pH value, and the presence of foreign salts (NaCl and KCl). The experimental results indicated that the adsorption process reached equilibrium in about 4 h. A drop in the amount of phenol removal, especially at higher initial concentration, was noticed upon increasing the temperature from 25 to 45 °C. This reflects the exothermic nature of the adsorption process. This was also confirmed by the calculated negative enthalpy of adsorption (-64.8 kJ/mol). A pH of 6 was found to be the optimum value at which the highest phenol removal occurred with around 15 mg/g at 25 °C for an initial concentration of 200 ppm. The presence of foreign salts has negatively affected the phenol adsorption process. The fitting of the experimental data, using different adsorption isotherms, indicated that the Harkins-Jura isotherm model was the best fit, evident by the high square of the correlation coefficient (R²) values greater than 0.96. The kinetic study revealed that the adsorption was represented by a pseudo-second-order reaction. The results of this study offer a basis to use Ziziphus leaves as promising adsorbents for efficient phenol removal from wastewater.

Environmental impacts of solar photovoltaic systems: A critical review of recent progress and future outlook

Photovoltaic (PV) systems are regarded as clean and sustainable sources of energy. Although the operation of PV systems exhibits minimal pollution during their lifetime, the probable environmental impacts of such systems from manufacturing until disposal cannot be ignored. The production of hazardous contaminates, water resources pollution, and emissions of air pollutants during the manufacturing process as well as the impact of PV installations on land use are important environmental factors to consider. The present study aims at developing a comprehensive analysis of all possible environmental challenges as well as presenting novel design proposals to mitigate and solve the aforementioned environmental problems. The emissions of greenhouse gas (GHG) from various PV systems were also explored and compared with fossil fuel energy resources. The results revealed that the negative environmental impacts of PV systems could be substantially mitigated using optimized design, development of novel materials, minimize the use of hazardous materials, recycling whenever possible, and careful site selection. Such mitigation actions will reduce the emissions of GHG to the environment, decrease the accumulation of solid wastes, and preserve valuable water resources. The carbon footprint emission from PV systems was found to be in the range of 14-73 g CO₂-eq/kWh, which is 10 to 53 orders of magnitude lower than emission reported from the burning of oil (742 g CO₂-eq/kWh from oil). It was concluded that the carbon footprint of the PV system could be decreased further by one order of magnitude using novel manufacturing materials. Recycling solar cell materials can also contribute up to a 42% reduction in GHG emissions. The present study offers a valuable management strategy that can be used to improve the sustainability of PV manufacturing processes, improve its economic value, and mitigate its negative impacts on the environment.

Impact of Emerging Technologies on Virgin Olive Oil Processing, Consumer Acceptance, and the Valorization of Olive Mill Wastes

There is a growing consumer preference for high quality extra virgin olive oil (EVOO) with health-promoting and sensory properties that are associated with a higher content of phenolic and volatile compounds. To meet this demand, several novel and emerging technologies are being under study to be applied in EVOO production. This review provides an update of the effect of emerging technologies (pulsed electric fields, high pressure, ultrasound, and microwave treatment), compared to traditional EVOO extraction, on yield, quality, and/or content of some minor compounds and bioactive components, including phenolic compounds, tocopherols, chlorophyll, and carotenoids. In addition, the consumer acceptability of EVOO is discussed. Finally, the application of these emerging technologies in the valorization of olive mill wastes, whose generation is of concern due to its environmental impact, is also addressed.

Advanced microbial fuel cell for waste water treatment-a review

Petroleum, coal, and natural gas reservoir were depleting continuously due to an increase in industrialization, which enforced study to identify alternative sources. The next option is the renewable resources which are most important for energy purpose coupled with environmental problem reduction. Microbial fuel cells (MFCs) have become a promising approach to generate cleaner and more sustainable electrical energy. The involvement of various disciplines had been contributing to enhancing the performance of the MFCs. This review covers the performance of MFC along with different wastewater as a substrate in terms of treatment efficiencies as well as for energy generation. Apart from this, effect of various parameters and use of different nanomaterials for performance of MFC were also studied. From the current study, it proves that the use of microbial fuel cell along with the use of nanomaterials could be the waste and energy-related problem-solving approach. MFC could be better in performances based on optimized process parameters for handling any wastewater from industrial process.

Combined ultrasound-ozone treatment for reutilization of primary effluent-a preliminary study

The present work is a preliminary study on the potential of low-frequency ultrasound irradiation coupled with O₃ process for the disinfection of a primary effluent from a municipal wastewater treatment plant preserving nutrient levels (in particular nitrogen and phosphorous), for its possible reuse in civil, industrial, and agricultural sectors. The treated water could be reused, after appropriate dilution, contributing to the circular economy perspective and reducing the need for both chemical fertilizer addition and freshwater supply. The effect of different specific ultrasonic energies and ozone doses was assessed on a bench-top system, composed of an ultrasonic reactor and a semi-batch ozonation vessel. The results showed that the combined US-O₃ process produces a good removal efficiency regarding soluble Chemical Oxygen Demand, sCOD (ca. 60%), anionic surfactants (ca. 50%), and formaldehyde (ca. 50%), and an optimal abatement for Methylene Blue Active Substances (MBAS, > 90%). The process also reached high disinfection performances, obtaining 4 logs for E. coli and 5 log abatement for Total Coliforms. The high removal efficiency is matched by an outstanding retention of nutrients (total nitrogen and orthophosphate) highlighting a high potential value for agricultural reuse of the treated primary effluent, with possible significant saving of chemical fertilizers. It was concluded that low-frequency ultrasound pre-treatment, combined with ozonation, could be a useful process for primary effluent recovery for several purposes. Further studies are expected to be planned and executed to evaluate system scale-up feasibility.

Combined electrocoagulation processes as a novel approach for enhanced pollutants removal: A state-of-the-art review

A novel approach using the integration of electrocoagulation, with one or more treatment processes has been recently practiced to improve the removal of colloidal and non-biodegradable pollutants. Several treatment processes including adsorption, chemical coagulation, magnetic field, reverse osmosis, and membrane filtration have been combined with electrocoagulation treatment step to improve pollutants removal efficiency. These combined systems showed the potential to improve the performance of the treatment process. This paper presents a state-of-the-art review for the recent processes available in the literature that combine treatment electrocoagulation with one of the previously mentioned treatment processes. It is found that the removal efficiency of any combined processes is higher than that of any single treatment process and the combined process has up to 20% higher removal efficiency compared to electrocoagulation alone. However, most reported studies were conducted at bench-scale level with synthetic wastewater instead of real wastewater. The main aspects of these combined systems including process mechanism, kinetic models, cost and the scale up of combined processes were discussed and summarized. Finally, several concluding remarks were drawn in view of the literature investigations and the gaps that suggest more studies and insights for future development were addressed.

Energy and Economic Analysis of Date Palm Biomass Feedstock for Biofuel Production in UAE: Pyrolysis, Gasification and Fermentation

This work evaluates date palm waste as a cheap and available biomass feedstock in UAE for the production of biofuels. The thermochemical and biochemical routes including pyrolysis, gasification, and fermentation were investigated. Simulations were done to produce biofuels from biomass via Aspen Plus v.10. The simulation results showed that for a tonne of biomass feed, gasification produced 56 kg of hydrogen and fermentation yielded 233 kg of ethanol. Process energy requirements, however, proved to offset the bioethanol product value. For 1 tonne of biomass feed, the net duty for pyrolysis was 37 kJ, for gasification was 725 kJ, and for fermentation was 7481.5 kJ. Furthermore, for 1 tonne of date palm waste feed, pyrolysis generated a returned USD $768, gasification generated USD 166, but fermentation required an expenditure of USD 763, rendering it unfeasible. The fermentation economic analysis showed that reducing the system’s net duty to 6500 kJ/tonne biomass and converting 30% hemicellulose along with the cellulose content will result in a breakeven bioethanol fuel price of 1.85 USD/L. This fuel price falls within the acceptable 0.8–2.4 USD/L commercial feasibility range and is competitive with bioethanol produced in other processes. The economic analysis indicated that pyrolysis and gasification are economically more feasible than fermentation. To maximize profits, the wasted hemicellulose and lignin from fermentation are proposed to be used in thermochemical processes for further fuel production.

Effluents detoxification from pulp and paper industry using microbial engineering and advanced oxidation techniques

Due to the high demand of paper and related items, pulp and paper industry is flourishing day by day. With increased production, come the hazards associated with the toxic elements present in the effluents. Various microorganisms are currently employed in the remediation of these toxic effluents. In addition, various techniques like ozonation, electrocoagulation, UV treatment, Fenton's reagent, and photo-Fenton based techniques are used in advanced oxidation processes to reduce these toxins from effluents. This review highlights various above mentioned advanced techniques and innovative processes along with the biological remediation of these toxic effluents with the help of some potential microbial consortia or their combinatory effects. Moreover, the present review will also disclose the ideas on utilizing the tools of metabolic engineering, systems biology, and artificial intelligence towards microbial engineering for relatively better bioremediation processes. In the future, these techniques might be helpful in increasing the capability of microbial consortia towards detoxification of effluents to make them environmentally safe. Finally, this review gives well-synchronized approaches to get more insights into these innovative methodologies and techniques and their use for various industrial applications.

Ultrasonic degradation of nitrosodipropylamine (NDPA) and nitrosodibutylamine (NDBA) in water

Nitrosodipropylamine (NDPA) and nitrosodibutylamine (NDBA), two highly toxics and carcinogenic disinfection by-products, cannot be efficiently removed by conventional water treatment processes, while the ultrasound treatment was developed as a promising alternative. In this work, nitrosodipropylamine (NDPA) and nitrosodibutylamine (NDBA) are degraded by ultrasound treatment. Greater than 99% of NDPA and NDBA mixing solution could be decomposed within 60 min at neutral pH under optimal ultrasound power and frequency settings of 100 W and 600 kHz, respectively. Free radical reactions (OH•) played a significant role and the reaction sites were predominately at the bubble interface. The degradation of both NDPA and NDBA exhibited pseudo-first-order degradation kinetics, and the rate constant k_app was influenced by a number of factors including ultrasonic frequency, power, initial concentration, initial pH, various anions and cations frequently present in drinking water, hydroxyl radical scavengers, and water matrices, especially the promoting effect of various anions and cations and water matrices. The results of this study suggest the potential for ultrasound treatment as a method for removing NAms from water.