Digital breast tomosynthesis: studies of the effects of acquisition geometry on contrast-to-noise ratio and observer preference of low-contrast objects in breast phantom images

Optimizing angular range in digital breast tomosynthesis: A phantom study investigating lesion detection across varied breast density and thickness

PURPOSE

To determine the optimal angular range (AR) for digital breast tomosynthesis (DBT) systems that provides highest lesion visibility across various breast densities and thicknesses.

METHOD

A modular DBT phantom, consisting of tissue-equivalent adipose and glandular modules, along with a module embedded with test objects (speckles, masses, fibers), was used to create combinations simulating different breast thicknesses, densities, and lesion locations. A prototype DBT system operated at four ARs (AR±7.5°, AR±12.5°, AR±19°, and AR±25°) to acquire 11 projection images for each combination, with separate fixed doses for thin and thick combinations. Three blinded radiologists independently assessed lesion visibility in reconstructed images; assessments were averaged and compared using linear mixed models.

RESULTS

Speckle visibility was highest with AR±7.5° or AR±12.5°, decreasing with wider ARs in all density and thickness combinations. The difference between AR±7.5° and AR±12.5° was not statistically significant, except for the tube-side speckles in thin-fatty combinations (5.83 [AR±7.5°] vs. 5.39 [AR±12.5°], P = 0.019). Mass visibility was not affected by AR in thick combinations, while AR±12.5° exhibited the highest mass visibility for both thin-fatty and thin-dense combinations (P = 0.032 and 0.007, respectively). Different ARs provided highest fiber visibility for different combinations; however, AR±12.5° consistently provided highest or comparable visibility. AR±12.5° showed highest overall lesion visibility for all density and thickness combinations.

CONCLUSIONS

AR±12.5° exhibited the highest overall lesion visibility across various phantom thicknesses and densities using a projection number of 11.

Examining the Influence of Digital Phantom Models in Virtual Imaging Trials for Tomographic Breast Imaging

Purpose

Digital phantoms are one of the key components of virtual imaging trials (VITs) that aims to assess and optimize new medical imaging systems and algorithms. However, these phantoms vary in their voxel resolution, appearance and structural details. This study aims to examine whether and how variations between digital phantoms influence system optimization with digital breast tomosynthesis (DBT) as a chosen modality.

Methods

We selected widely used and open access digital breast phantoms generated with different methods. For each phantom type, we created an ensemble of DBT images to test acquisition strategies. Human observer localization ROC (LROC) was used to assess observer performance studies for each case. Noise power spectrum (NPS) was estimated to compare the phantom structural components. Further, we computed several gaze metrics to quantify the gaze pattern when viewing images generated from different phantom types.

Results

Our LROC results show that the arc samplings for peak performance were approximately 2.5° and 6° in Bakic and XCAT breast phantoms respectively for 3-mm lesion detection task and indicate that system optimization outcomes from VITs can vary with phantom types and structural frequency components. Additionally, a significant correlation (p¡0.01) between gaze metrics and diagnostic performance suggests that gaze analysis can be used to understand and evaluate task difficulty in VITs.

Conclusion

Our results point to the critical need to evaluate realism in digital phantoms as well as ensuring sufficient structural variations at spatial frequencies relevant to the signal size for an intended task. In addition, standardizing phantom generation and validation tools might aid in lower discrepancies among independently conducted VITs for system or algorithmic optimizations.

Comparison of lesion detection and conspicuity between narrow-angle and wide-angle digital breast tomosynthesis for dense and non-dense breasts

Digital breast tomosynthesis (DBT) has been shown to improve both sensitivity and specificity for breast cancer detection compared to full-field digital mammography. However, its performance could be limited for patients with dense breasts. Clinical DBT systems vary in their system designs, one of which is the acquisition angular range (AR), which leads to varied performance for different imaging tasks. In this study, we aim to compare DBT systems with different AR. We used a previously validated cascaded linear system model to investigate the dependence of in-plane breast structural noise (BSN) and detectability of masses on AR. We conducted a pilot clinical study to compare the lesion conspicuity between clinical DBT systems with the narrowest and the widest AR. Patients called back for diagnostic imaging on suspicious findings were imaged with both narrow-angle (NA) and wide-angle (WA) DBT. We analyzed the BSN for clinical images using noise power spectrum (NPS) analysis. A 5-point Likert scale was used in the reader study to compare the lesion conspicuity. Our theoretical calculation results show that increasing AR leads to reduced BSN and improved mass detectability. The NPS analysis on clinical images shows the lowest BSN for WA DBT. The WA DBT provides better lesion conspicuity for masses and asymmetries and shows a greater advantage for non-microcalcification lesions in dense breasts. The NA DBT provides better characterizations for microcalcifications. The WA DBT can downgrade false-positive findings seen on NA DBT. In conclusion, WA DBT could improve the detection of masses and asymmetries for patients with dense breasts.

Performance evaluation of digital breast tomosynthesis systems: physical methods and experimental data

Digital breast tomosynthesis (DBT) has become a well-established breast imaging technique, whose performance has been investigated in many clinical studies, including a number of prospective clinical trials. Results from these studies generally point to non-inferiority in terms of microcalcification detection and superior mass-lesion detection for DBT imaging compared to digital mammography (DM). This modality has become an essential tool in the clinic for assessment and ad-hoc screening but is not yet implemented in most breast screening programmes at a state or national level. While evidence on the clinical utility of DBT has been accumulating, there has also been progress in the development of methods for technical performance assessment and quality control of these imaging systems. DBT is a relatively complicated ‘pseudo-3D’ modality whose technical assessment poses a number of difficulties. This paper reviews methods for the technical performance assessment of DBT devices, starting at the component level in part one and leading up to discussion of system evaluation with physical test objects in part two. We provide some historical and basic theoretical perspective, often starting from methods developed for DM imaging. Data from a multi-vendor comparison are also included, acquired under the medical physics quality control protocol developed by EUREF and currently being consolidated by a European Federation of Organisations for Medical Physics working group. These data and associated methods can serve as a reference for the development of reference data and provide some context for clinical studies.

Variation in digital breast tomosynthesis image quality at differing heights above the detector

INTRODUCTION

The aim of this preliminary work was to determine if image quality in digital breast tomosynthesis (DBT) changes when tomosynthesis image slices were obtained at differing heights above the detector and in differing breast thicknesses.

METHODS

A CIRS Model 020 BR3D breast imaging phantom was used to obtain the DBT images. The images were also acquired at different tube voltages, and each exposure was determined by the automatic exposure control system. Contrast-to-noise ratio (CNR) and figure-of-merit (FOM) values were obtained and compared.

RESULTS

At a phantom thickness of 5 cm or greater, there was a significant reduction (P ≤ 0.05) of image CNR values obtained from the images near the top of the phantom to those obtained near the bottom of the phantom. When the phantom thickness was 4 cm, there was no significant difference in CNR values between DBT images acquired at any height in the phantom. FOM values generally showed no difference when images were obtained at differing heights above the detector.

CONCLUSION

Image quality, as measured by the CNR, was reduced when tomosynthesis slice image heights were at the top of the phantom and when the thickness of the phantom was more than 4 cm. From this preliminary work, clinicians need to be aware that DBT images obtained near the top of the breast, when breast thickness is greater than 4 cm, may have reduced image quality. Further work is needed to fully assess any DBT image quality changes when images are obtained near the top of the breast.

Two-phase learning-based 3D deblurring method for digital breast tomosynthesis images

In digital breast tomosynthesis (DBT) systems, projection data are acquired from a limited number of angles. Consequently, the reconstructed images contain severe blurring artifacts that might heavily degrade the DBT image quality and cause difficulties in detecting lesions. In this study, we propose a two-phase learning approach for artifact compensation in a coarse-to-fine manner to mitigate blurring artifacts effectively along all viewing directions of the DBT image volume (i.e., along the axial, coronal, and sagittal planes) to improve the detection performance of lesions. The proposed method employs a convolutional neural network model comprising two submodels/phases, with Phase 1 performing three-dimensional (3D) deblurring and Phase 2 performing additional 2D deblurring. To investigate the effects of loss functions on the proposed model’s deblurring performance, we evaluated several loss functions, such as the pixel-based loss function, adversarial-based loss function, and perception-based loss function. Compared with the DBT image, the mean squared error of the image and the root mean squared errors of the gradient of the image decreased by 82.8% and 44.9%, respectively, and the contrast-to-noise ratio increased by 183.4% in the in-focus plane. We verified that the proposed method sequentially restored the missing frequency components as the DBT images were processed through the Phase 1 and Phase 2 steps. These results indicate that the proposed method performs effective 3D deblurring, significantly reducing the blurring artifacts in the in-focus plane and other planes of the DBT image, thus improving the detection performance of lesions.

Deep Convolutional Neural Network With Adversarial Training for Denoising Digital Breast Tomosynthesis Images

Digital breast tomosynthesis (DBT) is a quasi-three-dimensional imaging modality that can reduce false negatives and false positives in mass lesion detection caused by overlapping breast tissue in conventional two-dimensional (2D) mammography. The patient dose of a DBT scan is similar to that of a single 2D mammogram, while acquisition of each projection view adds detector readout noise. The noise is propagated to the reconstructed DBT volume, possibly obscuring subtle signs of breast cancer such as microcalcifications (MCs). This study developed a deep convolutional neural network (DCNN) framework for denoising DBT images with a focus on improving the conspicuity of MCs as well as preserving the ill-defined margins of spiculated masses and normal tissue textures. We trained the DCNN using a weighted combination of mean squared error (MSE) loss and adversarial loss. We configured a dedicated x-ray imaging simulator in combination with digital breast phantoms to generate realistic in silico DBT data for training. We compared the DCNN training between using digital phantoms and using real physical phantoms. The proposed denoising method improved the contrast-to-noise ratio (CNR) and detectability index (d') of the simulated MCs in the validation phantom DBTs. These performance measures improved with increasing training target dose and training sample size. Promising denoising results were observed on the transferability of the digital-phantom-trained denoiser to DBT reconstructed with different techniques and on a small independent test set of human subject DBT images.

Comparison of Narrow-angle and Wide-angle Digital Breast Tomosynthesis Systems in Clinical Practice

Digital breast tomosynthesis (DBT) is a pseudo 3D mammography imaging technique that has become widespread since gaining Food and Drug Administration approval in 2011. With this technology, a variable number of tomosynthesis projection images are obtained over an angular range between 15° and 50° for currently available clinical DBT systems. The angular range impacts various aspects of clinical imaging, such as radiation dose, scan time, and image quality, including visualization of calcifications, masses, and architectural distortion. This review presents an overview of the differences between narrow- and wide-angle DBT systems, with an emphasis on their applications in clinical practice. Comparison examples of patients imaged on both narrow- and wide-angle DBT systems illustrate these differences. Understanding the potential variable appearance of imaging findings with narrow- and wide-angle DBT systems is important for radiologists, particularly when comparison images have been obtained on a different DBT system. Furthermore, knowledge about the comparative strengths and limitations of DBT systems is needed for appropriate equipment selection.

Assessment of task-based performance from five clinical DBT systems using an anthropomorphic breast phantom

PURPOSE

Digital breast tomosynthesis (DBT) is a limited-angle tomographic breast imaging modality that can be used for breast cancer screening in conjunction with full-field digital mammography (FFDM) or synthetic mammography (SM). Currently, there are five commercial DBT systems that have been approved by the U.S. FDA for breast cancer screening, all varying greatly in design and imaging protocol. Because the systems are different in technical specifications, there is a need for a quantitative approach for assessing them. In this study, the DBT systems are assessed using a novel methodology with an inkjet-printed anthropomorphic phantom and four alternative forced choice (4AFC) study scheme.

METHOD

A breast phantom was fabricated using inkjet printing and parchment paper. The phantom contained 5-mm spiculated masses fabricated with potassium iodide (KI)-doped ink and microcalcifications (MCs) made with calcium hydroxyapatite. Images of the phantom were acquired on all five systems with DBT, FFDM, and SM modalities where available using beam settings under automatic exposure control. A 4AFC study was conducted to assess reader performance with each signal under each modality. Statistical analysis was performed on the data to determine proportion correct (PC), standard deviations, and levels of significance.

RESULTS

For masses, overall detection was highest with DBT. The difference in PC was statistically significant between DBT and SM for most systems. A relationship was observed between increasing PC and greater gantry span. For MCs, performance was highest with DBT and FFDM compared to SM. The difference between PC of DBT and PC of SM was statistically significant for all manufacturers.

CONCLUSIONS

This methodology represents a novel approach for evaluating systems. This study is the first of its kind to use an inkjet-printed anthropomorphic phantom with realistic signals to assess performance of clinical DBT imaging systems.

Technical evaluation of image quality in synthetic mammograms obtained from 15° and 40° digital breast tomosynthesis in a commercial system: a quantitative comparison

Digital breast tomosynthesis (DBT) has recently gained interest both for breast cancer screening and diagnosis. Its employment has increased also in conjunction with digital mammography (DM), to improve cancer detection and reduce false positive recall rate. Synthetic mammograms (SMs) reconstructed from DBT data have been introduced to replace DM in the DBT + DM approach, for preserving the benefits of the dual-acquisition modality whilst reducing radiation dose and compression time. Therefore, different DBT models have been commercialized and the effective potential of each system has been investigated. In particular, wide-angle DBT was shown to provide better depth resolution than narrow-angle DBT, while narrow-angle DBT allows better identification of microcalcifications compared to wide-angle DBT. Given the increasing employment of SMs as supplement to DBT, a comparison of image quality between SMs obtained in narrow-angle and wide-angle DBT is of practical interest. Therefore, the aim of this phantom study was to evaluate and compare the image quality of SMs reconstructed from 15° (SM₁₅) and 40° (SM₄₀) DBT in a commercial system. Spatial resolution, noise and contrast properties were evaluated through the modulation transfer function (MTF), noise power spectrum, maps of signal-to-noise ratio (SNR), image contrast, contrast-to-noise ratio (CNR) and contrast-detail (CD) thresholds. SM₄₀ expressed higher MTF than SM₁₅, but also lower SNR and CNR levels. SM₁₅ and SM₄₀ were characterized by slight different texture, and a different behavior in terms of contrast was found. SM₁₅ provided better CD performances than SM₄₀. These results suggest that the employment of wide/narrow-angle DBT + SM images should be optimized based on the specific image task.

Digital Breast Tomosynthesis: Technique and Common Artifacts

Image optimization at digital breast tomosynthesis (DBT) involves a series of trade-offs between multiple variables. Wider sweep angles provide better separation of overlapping tissues, but they result in decreased in-plane resolution as well as increased scan times that may be prone to patient motion. Techniques to reduce scan time, such as continuous tube motion and pixel binning during detector readout, reduce the chances of patient motion but may degrade the in-plane resolution. Image artifacts are inherent to DBT because of the limited angular range of the acquisition. Iterative reconstruction algorithms have been shown to reduce various DBT artifacts.

Human observer performance on in-plane digital breast tomosynthesis images: Effects of reconstruction filters and data acquisition angles on signal detection

For digital breast tomosynthesis (DBT) systems, we investigate the effects of the reconstruction filters for different data acquisition angles on signal detection. We simulated a breast phantom with a 30% volume glandular fraction (VGF) of breast anatomy using the power law spectrum and modeled the breast mass as a spherical object with a 1 mm diameter. Projection data were acquired using two different data acquisition angles and numbers of projection view pairs, and in-plane breast images were reconstructed using the Feldkamp-Davis-Kress (FDK) algorithm with three different reconstruction filter schemes. To measure the ability to detect a signal, we conducted the human observer study with a binary detection task and compared the signal detectability of human to that of channelized Hotelling observer (CHO) with Laguerre-Gauss (LG) channels and dense difference-of-Gaussian (D-DOG) channels. We also measured the contrast-to-noise ratio (CNR), signal power spectrum (SPS), and β values of the anatomical noise power spectrum (NPS) to show the association between human observer performance and these traditional metrics. Our results show that using a slice thickness (ST) filter degraded the signal detection performance of human observers at the same data acquisition angle. This could be predicted by D-DOG CHO with internal noise, but the correlation between the traditional metrics and signal detectability was not observed in this work.

Comprehensive assessment of image quality in synthetic and digital mammography: a quantitative comparison

Recent advances in digital breast tomosynthesis (DBT) technology were focused on the reconstruction of 2D "Synthesized Mammograms" (SMs) from DBT dataset. The introduction of SMs could avoid an additional digital mammography (DM) which is often required in complement to DBT examinations. Therefore, breast absorbed dose and compression time can be significantly reduced in DBT+SM procedures with respect to DBT+DM modality. However, to date, a limited number of studies have objectively characterised the image quality of SMs with respect to DM images. Therefore, the aim of this phantom study was to comprehensively compare SMs and DM images in terms of several image quality parameters. A Selenia Dimensions system (Hologic, Bedford, Mass, USA) was employed in this work. Five different phantoms were adopted to study noise, contrast and spatial resolution properties of the images. Specifically, noise power spectrum (NPS), maps of signal-to-noise ratio (SNR), contrast-to-noise ratio (CNR), modulation transfer function (MTF) and contrast-detail (CD) thresholds were evaluated both for SM and DM modalities. SMs were characterised by different texture, noise and SNR spatial distribution properties with respect to DM images. Additionally, while in some conditions SM provides higher CNR than DM, lower overall performances in terms spatial resolution and CD curves were found in comparison to DM images. Therefore, given the great benefits of SMs in terms of dose and compression time saving, further clinical investigations on SMs image quality properties could be of practical interest to integrate our findings.

Can Digital Breast Tomosynthesis Replace Full-Field Digital Mammography? A Multireader, Multicase Study of Wide-Angle Tomosynthesis

OBJECTIVE. The purpose of this study was to test the hypothesis whether two-view wide-angle digital breast tomosynthesis (DBT) can replace full-field digital mammography (FFDM) for breast cancer detection. SUBJECTS AND METHODS. In a multireader multicase study, bilateral two-view FFDM and bilateral two-view wide-angle DBT images were independently viewed for breast cancer detection in two reading sessions separated by more than 1 month. From a pool of 764 patients undergoing screening and diagnostic mammography, 330 patient-cases were selected. The endpoints were the mean ROC AUC for the reader per breast (breast level), ROC AUC per patient (subject level), noncancer recall rates, sensitivity, and specificity. RESULTS. Twenty-nine of 31 readers performed better with DBT than FFDM regardless of breast density. There was a statistically significant improvement in readers' mean diagnostic accuracy with DBT. The subject-level AUC increased from 0.765 (standard error [SE], 0.027) for FFDM to 0.835 (SE, 0.027) for DBT (p = 0.002). Breast-level AUC increased from 0.818 (SE, 0.019) for FFDM to 0.861 (SE, 0.019) for DBT (p = 0.011). The noncancer recall rate per patient was reduced by 19% with DBT (p < 0.001). Masses and architectural distortions were detected more with DBT (p < 0.001); calcifications trended lower (p = 0.136). Accuracy for detection of invasive cancers was significantly greater with DBT (p < 0.001). CONCLUSION. Reader performance in breast cancer detection is significantly higher with wide-angle two-view DBT independent of FFDM, verifying the robustness of DBT as a sole view. However, results of perception studies in the vision sciences support the inclusion of an overview image.

Synthesizing mammogram from digital breast tomosynthesis

The purpose of this study is to develop a new method for generating synthesized mammogram (SM) from digital breast tomosynthesis (DBT) and to assess its potential as an adjunct to DBT. We first applied multiscale bilateral filtering to the reconstructed DBT slices to enhance the high-frequency features and reduce noise. A maximum intensity projection (MIP) image was then obtained from the high-frequency components of the DBT slices. A multiscale image fusion method was designed to combine the MIP image and the central DBT projection view into an SM and further enhance the high-frequency features. We conducted a pilot reader study to visually assess the image quality of SM in comparison to full field digital mammograms (FFDM). For each DBT craniocaudal or mediolateral view, a clinical FFDM of the corresponding view was retrospectively collected. Three MQSA radiologists, blinded to the pathological and other clinical information, independently interpreted the SM and the corresponding FFDM side by side marked with the lesion locations. The differences in the BI-RADS assessments of both MCs and masses between SM and FFDM did not achieve statistical significance for all three readers. The conspicuity of MCs on SM was superior to that on FFDM and the BI-RADS assessments of MCs were comparable while the conspicuity of masses on SM was degraded and interpretation on SM was less accurate than that on FFDM. The SM may be useful for efficient prescreening of MCs in DBT but the DBT should be used for detection and characterization of masses.

Imaging of fiber-like structures in digital breast tomosynthesis

Fiber-like features are an important aspect of breast imaging. Vessels and ducts are present in all breast images, and spiculations radiating from a mass can indicate malignancy. Accordingly, fiber objects are one of the three types of signals used in the American College of Radiology digital mammography (ACR-DM) accreditation phantom. Our work focuses on the image properties of fiber-like structures in digital breast tomosynthesis (DBT) and how image reconstruction can affect their appearance. The impact of DBT image reconstruction algorithm and regularization strength on the conspicuity of fiber-like signals of various orientations is investigated in simulation. A metric is developed to characterize this orientation dependence and allow for quantitative comparison of algorithms and associated parameters in the context of imaging fiber signals. The imaging properties of fibers, characterized in simulation, are then demonstrated in detail with physical DBT data of the ACR-DM phantom. The characterization of imaging of fiber signals is used to explain features of an actual clinical DBT case. For the algorithms investigated, at low regularization setting, the results show a striking variation in conspicuity as a function of orientation in the viewing plane. In particular, the conspicuity of fibers nearly aligned with the plane of the x-ray source trajectory is decreased relative to more obliquely oriented fibers. Increasing regularization strength mitigates this orientation dependence at the cost of increasing depth blur of these structures.

The threshold detectable mass diameter for 2D-mammography and digital breast tomosynthesis

Digital breast tomosynthesis (DBT) is currently under consideration for replacement of, or combined use with 2D-mammography in national breast screening programmes. To investigate the potential benefits that DBT can bring to screening, the threshold detectable lesion diameters were measured for different forms of DBT in comparison to 2D-mammography. The aim of this study was to compare the threshold detectable mass diameters obtained with narrow angle (15°/15 projections) and wide angle (50°/25 projections) DBT in comparison to 2D-mammography. Simulated images of 60 mm thick compressed breasts were produced with and without masses using a set of validated image modelling tools for 2D-mammography and DBT. Image processing and reconstruction were performed using commercial software. A series of 4-alternative forced choice (4AFC) experiments was conducted for signal detection with the masses as targets. The threshold detectable mass diameter was found for each imaging modality with a mean glandular dose of 2.5 mGy. The resulting values of the threshold diameter for 2D-mammography (10.2 ± 1.4 mm) were found to be larger (p < 0.001) than those for narrow angle DBT (6.0 ± 1.1 mm) and wide angle DBT (5.6 ± 1.2 mm). There was no significant difference between the threshold diameters for wide and narrow angle DBT. Implications for the introduction of DBT alone or in combination with 2D-mammography in breast cancer screening are discussed.

Preliminary Clinical Experience with a Combined Automated Breast Ultrasound and Digital Breast Tomosynthesis System

We analyzed the performance of a mammographically configured, automated breast ultrasound (McABUS) scanner combined with a digital breast tomosynthesis (DBT) system. The GE Invenia ultrasound system was modified for integration with GE DBT systems. Ultrasound and DBT imaging were performed in the same mammographic compression. Our small preliminary study included 13 cases, six of whom had contained invasive cancers. From analysis of these cases, current limitations and corresponding potential improvements of the system were determined. A registration analysis was performed to compare the ease of McABUS to DBT registration for this system with that of two systems designed previously. It was observed that in comparison to data from an earlier study, the McABUS-to-DBT registration alignment errors for both this system and a previously built combined system were smaller than those for a previously built standalone McABUS system.

Detectability comparison of simulated tumors in digital breast tomosynthesis using high-energy X-ray inline phase sensitive and commercial imaging systems

This study compared the detectability of simulated tumors using a high-energy X-ray inline phase sensitive digital breast tomosynthesis (DBT) prototype and a commercial attenuation-based DBT system. Each system imaged a 5-cm thick modular breast phantom with 50-50 adipose-glandular percentage density containing contrast-detail (CD) test objects to simulate different tumor sizes. A commercial DBT system acquired 15 projection views over 15 degrees (15d-15p) was used to acquire the attenuation-based projection views and to reconstruct the conventional DBT slices. Attenuation-based projection views were acquired at 32 kV, 46 mAs with a mean glandular dose (D_g) of 1.6 mGy. For acquiring phase sensitive projection views, the prototype utilized two acquisition geometries: 11 projection views were acquired over 15 degrees (15d-11p), and 17 projection views were acquired over 16 degrees (16d-17p) at 120 kV, 5.27 mAs with 1.51 mGy under the magnification (M) of 2. A phase retrieval algorithm based on the phase-attenuation duality (PAD) was applied to each projection view, and a modified Feldkamp-Davis-Kress (FDK) algorithm was used to reconstruct the phase sensitive DBT slices. Simulated tumor margins were rated as more conspicuous and better visualized for both phase sensitive acquisition geometries versus conventional DBT imaging. The CD curves confirmed the improvement in both contrast and spatial resolutions with the phase sensitive DBT imaging. The superiority of the phase sensitive DBT imaging was further endorsed by higher contrast to noise ratio (CNR) and figure-of-merit (FOM) values. The CNR improvements provided by the phase sensitive DBT prototype were sufficient to offset the noise reduction provided by the attenuation-based DBT imaging.

Improving image quality for digital breast tomosynthesis: an automated detection and diffusion-based method for metal artifact reduction

In digital breast tomosynthesis (DBT), the high-attenuation metallic clips marking a previous biopsy site in the breast cause errors in the estimation of attenuation along the ray paths intersecting the markers during reconstruction, which result in interplane and inplane artifacts obscuring the visibility of subtle lesions. We proposed a new metal artifact reduction (MAR) method to improve image quality. Our method uses automatic detection and segmentation to generate a marker location map for each projection (PV). A voting technique based on the geometric correlation among different PVs is designed to reduce false positives (FPs) and to label the pixels on the PVs and the voxels in the imaged volume that represent the location and shape of the markers. An iterative diffusion method replaces the labeled pixels on the PVs with estimated tissue intensity from the neighboring regions while preserving the original pixel values in the neighboring regions. The inpainted PVs are then used for DBT reconstruction. The markers are repainted on the reconstructed DBT slices for radiologists' information. The MAR method is independent of reconstruction techniques or acquisition geometry. For the training set, the method achieved 100% success rate with one FP in 19 views. For the test set, the success rate by view was 97.2% for core biopsy microclips and 66.7% for clusters of large post-lumpectomy markers with a total of 10 FPs in 58 views. All FPs were large dense benign calcifications that also generated artifacts if they were not corrected by MAR. For the views with successful detection, the metal artifacts were reduced to a level that was not visually apparent in the reconstructed slices. The visibility of breast lesions obscured by the reconstruction artifacts from the metallic markers was restored.

Task-Based Modeling of a 5k Ultra-High-Resolution Medical Imaging System for Digital Breast Tomosynthesis

High-resolution, low-noise X-ray detectors based on CMOS active pixel sensor (APS) technology have demonstrated superior imaging performance for digital breast tomosynthesis (DBT). This paper presents a task-based model for a high-resolution medical imaging system to evaluate its ability to detect simulated microcalcifications and masses as lesions for breast cancer. A 3-D cascaded system analysis for a 50- [Formula: see text] pixel pitch CMOS APS X-ray detector was integrated with an object task function, a medical imaging display model, and the human eye contrast sensitivity function to calculate the detectability index and area under the ROC curve (AUC). It was demonstrated that the display pixel pitch and zoom factor should be optimized to improve the AUC for detecting small microcalcifications. In addition, detector electronic noise of smaller than 300 e^- and a high display maximum luminance (>1000 cd/cm ²) are desirable to distinguish microcalcifications of [Formula: see text] in size. For low contrast mass detection, a medical imaging display with a minimum of 12-bit gray levels is recommended to realize accurate luminance levels. A wide projection angle range of greater than ±30° in combination with the image gray level magnification could improve the mass detectability especially when the anatomical background noise is high. On the other hand, a narrower projection angle range below ±20° can improve the small, high contrast object detection. Due to the low mass contrast and luminance, the ambient luminance should be controlled below 5 cd/ [Formula: see text]. Task-based modeling provides important firsthand imaging performance of the high-resolution CMOS-based medical imaging system that is still at early stage development for DBT. The modeling results could guide the prototype design and clinical studies in the future.

Inverse filtering approach to measure directional in-plane modulation transfer function using a sphere phantom for a digital tomosynthesis system

We propose a method to measure the directional in-plane modulation transfer function (MTF) of a digital tomosynthesis system using a sphere phantom. To assess the spatial resolution of an in-plane image of the tomosynthesis system, projection data of a sphere phantom were generated within a limited data acquisition range of 40°, and reconstructed by the FDK algorithm. To measure the in-plane MTF, we divided the Fourier transform of the reconstructed sphere phantom by that of the ideal sphere phantom, and then performed plane integral along the fz-direction. When dividing, small values in the denominator can introduce estimation errors, and these errors were reduced by the proposed method. To evaluate the performance of the proposed method, the in-plane MTF estimated by simulation and experimental data was compared to the ideal in-plane MTF generated by computer simulations using a point object. For quantitative evaluation, we measured frequency values at half-maximum and full-maximum of the directional in-plane MTF along the three different directions (i.e., f_0° -, f_30° -, and f_60° -directions) and compared them with those of the ideal in-plane MTF. Although the sphere phantom has been regarded as an inappropriate object due to the anisotropic characteristics of tomosynthesis image, our results show that the proposed method has a reliable estimation performance, demonstrating the sphere phantom is still suitable for measuring the directional in-plane MTF for a digital tomosynthesis system.

Optimization of digital breast tomosynthesis (DBT) acquisition parameters for human observers: effect of reconstruction algorithms

We showed in our earlier work that the choice of reconstruction methods does not affect the optimization of DBT acquisition parameters (angular span and number of views) using simulated breast phantom images in detecting lesions with a channelized Hotelling observer (CHO). In this work we investigate whether the model-observer based conclusion is valid when using humans to interpret images. We used previously generated DBT breast phantom images and recruited human readers to find the optimal geometry settings associated with two reconstruction algorithms, filtered back projection (FBP) and simultaneous algebraic reconstruction technique (SART). The human reader results show that image quality trends as a function of the acquisition parameters are consistent between FBP and SART reconstructions. The consistent trends confirm that the optimization of DBT system geometry is insensitive to the choice of reconstruction algorithm. The results also show that humans perform better in SART reconstructed images than in FBP reconstructed images. In addition, we applied CHOs with three commonly used channel models, Laguerre-Gauss (LG) channels, square (SQR) channels and sparse difference-of-Gaussian (sDOG) channels. We found that LG channels predict human performance trends better than SQR and sDOG channel models for the task of detecting lesions in tomosynthesis backgrounds. Overall, this work confirms that the choice of reconstruction algorithm is not critical for optimizing DBT system acquisition parameters.