Performance of a high-rate membrane bioreactor for energy-efficient treatment of textile wastewater

High-rate membrane bioreactors (MBR), where the wastewater undergoes partial oxidation due to the applied short sludge retention time (SRT) and hydraulic retention time (HRT) values, retain the majority of the organic substances in the sludge through growth and biological flocculation. Thus, a raw material source with a high biomethane production potential is created for the widespread use of circular economy or energy-neutral plants in wastewater treatment. While high-rate MBRs have been successfully employed for energy-efficient treatment of domestic wastewater, there is a lack of research specifically focused on textile wastewater. This study aimed to investigate the textile wastewater treatment and organic matter recovery performances of an aerobic MBR system containing a hollow fiber ultrafiltration membrane with a 0.04 μm pore diameter. The system was initially operated at short SRTs (5 and 3 d) and different SRT/HRT ratios (5, 10, and 20) and subsequently at high-rate conditions (SRT of 0.5-2 d and HRT of 1.2-9.6 h) which are believed to be the most limiting conditions tested for treatment of real textile wastewater. The results showed that chemical oxygen demand (COD) removal averaged 77% even at SRT of 0.5 d and HRT of 1.2 h. Slowly biodegradable substrates and soluble microbial products (SMP) accumulated within the MBR at SRT of 0.5 and 1 d, which resulted in decreased sludge filterability. The observed sludge yield (Yobs) exhibited a considerable increase when SRT was reduced from 5 to 1 d. On the other hand, the SRT/HRT ratio displayed a decisive effect on the energy requirement for aeration.

Microalgal and activated sludge processing for biodegradation of textile dyes

The textile industry contributes substantially to water pollution. To investigate bioremediation of dye-containing wastewater, the decolorization and biotransformation of three textile azo dyes, Red HE8B, Reactive Green 27, and Acid Blue 29, were considered using an integrated remediation approach involving the microalga Chlamydomonas mexicana and activated sludge (ACS). At a 5 mg L-1 dye concentration, using C. mexicana and ACS alone, decolorization percentages of 39%-64% and 52%-54%, respectively, were obtained. In comparison, decolorization percentages of 75%-79% were obtained using a consortium of C. mexicana and ACS. The same trend was observed for the decolorization of dyes at higher concentrations, but the potential for decolorization was low. The toxic azo dyes adversely affect the growth of microalgae and at high concentration 50 mg L-1 the growth rate inhibited to 50-60% as compared to the control. The natural textile wastewater was also treated with the same pattern and got promising results of decolorization (90%). Moreover, the removal of BOD (82%), COD (72%), TN (64%), and TP (63%) was observed with the consortium. The HPLC and GC-MS confirm dye biotransformation, revealing the emergence of new peaks and the generation of multiple metabolites with more superficial structures, such as N-hydroxy-aniline, naphthalene-1-ol, and sodium hydroxy naphthalene. This analysis demonstrates the potential of the C. mexicana and ACS consortium for efficient, eco-friendly bioremediation of textile azo dyes.

Emerging pollutants in textile wastewater: an ecotoxicological assessment focusing on surfactants

Water and several chemicals, including dyestuffs, surfactants, acids, and salts, are required during textile dyeing processes. Surfactants are harmful to the aquatic environment and induce several negative biological effects in exposed biota. In this context, the present study aimed to assess acute effects of five surfactants, comprising anionic and nonionic classes, and other auxiliary products used in fiber dyeing processes to aquatic organisms Vibrio fischeri (bacteria) and Daphnia similis (cladocerans). The toxicities of binary surfactant mixtures containing the anionic surfactant dodecylbenzene sulfonate + nonionic fatty alcohol ethoxylate and dodecylbenzene sulfonate + nonionic alkylene oxide were also evaluated. Nonionic surfactants were more toxic than anionic compounds for both organisms. Acute nonionic toxicity ranged from 1.3 mg/L (fatty alcohol ethoxylate surfactant) to 2.6 mg/L (ethoxylate surfactant) for V. fischeri and from 1.9 mg/L (alkylene oxide surfactant) to 12.5 mg/L (alkyl aryl ethoxylated and aromatic sulfonate surfactant) for D. similis, while the anionic dodecylbenzene sulfonate EC50s were determined as 66.2 mg/L and 19.7 mg/L, respectively. Both mixtures were very toxic for the exposed organisms: the EC50 average in the anionic + fatty alcohol ethoxylate mixture was of 1.0 mg/L ± 0.11 for V. fischeri and 4.09 mg/L ± 0.69 for D. similis. While the anionic + alkylene oxide mixture, EC50 of 3.34 mg/L for D. similis and 3.60 mg/L for V. fischeri. These toxicity data suggested that the concentration addition was the best model to explain the action that is more likely to occur for mixture for the dodecylbenzene sulfonate and alkylene oxide mixtures in both organisms. Our findings also suggest that textile wastewater surfactants may interact and produce different responses in aquatic organisms, such as synergism and antagonism. Ecotoxicological assays provide relevant information concerning hazardous pollutants, which may then be adequately treated and suitably managed to reduce toxic loads, associated to suitable management plans.

Chitosan anchored nZVI bionanocomposites for treatment of textile wastewater: Optimization, mechanism, and phytotoxic assessment

In recent years, there has been a growing focus on treating textile wastewater due to its escalating threat to aquatic ecosystems and exposed communities. The present study investigates the adsorption efficacy of biopolymer functionalized nanoscale zero-valent iron (CS@nZVI) composite for the treatment of textile wastewater using the RSM-CCD model. The structure and morphology of CS@nZVI were characterized using XRD, FTIR, FESEM, and EDX. CS@nZVI was then evaluated for its adsorption potential in removing COD, color, and other physico-chemical parameters from textile wastewater. The results showed the high efficacy of CS@nZVI for COD and color removal from textile wastewater. Under optimal conditions (pH 6, contact time 60 min, and 1.84 g CS@nZVI), COD removal reached a maximum of 85.53%, and decolorization efficiency was found to be 89.73%. The coefficient of determination R2 (0.98) and AIC (269.75) values suggested quadratic model as the best-fitted model for optimizing the process parameters for COD removal. Additionally, the physico-chemical parameters were found to be within permissible limits after treatment with CS@nZVI. The influence of coexisting ions on COD removal followed the order PO43- > SO42- > Cl- >Na+ > Ca2+. The kinetics data fitted well with the pseudo-first-order reaction, indicating physisorption as the primary mechanism. The thermodynamic study revealed the endothermic nature of the removal process. Reusability tests demonstrated that great regeneration capacity of spent CS@nZVIafter five consecutive cycles. Furthermore, toxicological studies showed reduced toxicity in treated samples, leading to improved growth of Vigna radiata L. These findings suggest that CS@nZVI bionanocomposites could serve as an efficient, cost-effective, and eco-friendly remediation agent for the treatment of textile effluents, presenting significant prospects for commercial applications.

Application of montmorillonite/octadecylamine nanoparticles in the removal of textile dye from aqueous solutions: Modeling, kinetic, and equilibrium studies

In the study, the proliferation of industries has been associated with an increase in the production of industrial wastewater and subsequent environmental pollution, wherein dyes emerge as prominent pollutants. The characteristics of nanoclay modified with octadecylamine, were elucidated throughvarious techniques, including Field Emission Scanning Electron Microscopy/Energy Dispersive Spectroscopy (FE-SEM/EDS), Fourier Transform Infrared Spectroscopy (FTIR), Thermogravimetric Analysis (TGA), X-ray Diffraction (XRD), and Brunauer-Emmett-Teller Surface Area Analysis (BET). The research delved into the impact of variables such as pH, initial dye concentration, adsorbent dose, temperature, and ultrasonication time on the removal of Acid Black 1 (AB1) through an ultrasonic process, employing a central composite design (CCD). Optimal conditions for the adsorption process were determined: pH at 5.46, adsorbent mass at 4 mg/30 mL, initial dye concentration at 20 mg/L, ultrasound time at 20 min, and temperature at 50 °C, resulting in a remarkable 96.49% adsorption efficiency. The fitting of experimental equilibrium data to different isotherm models, including Langmuir, Freundlich, and Temkin, indicated thatthe Freundlich model was the most suitable. Analysis of the adsorption data with various kinetic models such as pseudo-first and second-order models, and intraparticle diffusion models, revealed the applicability of the second-order equation model. A thermodynamic study unveiled that the adsorption process was spontaneous and endothermic. In conclusion, the study highlights the significant capability ofmontmorillonite nanoclay modified with octadecylamine in removing AB1 dye, rendering it a viable option for wastewater treatment.

Assessment of heavy metals accumulation by vegetables irrigated with different stages of textile wastewater for evaluation of food and health risk

Wastewater irrigation for vegetable cultivation is greatly concerned about the presence of toxic metals in irrigated soil and vegetables which causes possible threats to human health. This study aimed to ascertain the accumulation of heavy metals (HMs) in edible parts of vegetables irrigated with different stages of textile dyeing wastewater (TDW). Bio-concentration factor (BCF), Estimated daily intake (EDI), and target hazard quotient (THQ) were computed to estimate human health risks and speculate the hazard index (HI) of adults and children with the consumption of HMs contaminated vegetables at recommended doses. Five vegetables (red amaranth, Indian spinach, cauliflower, tomato, and radish) in a pot experiment were irrigated with groundwater (T1) and seven stages of TDW (T2∼T8) following a randomized complete block design (RCBD) with three replications. Among the TDW stages, T8, T7, T4, and T5 exhibited elevated BCF, EDI, THQ, and HI due to a rising trend in the accumulation of Pb, Cd, Cr, and Ni heavy metals in the edible portion of the red amaranth, followed by radish, Indian spinach, cauliflower, and tomato. The general patterns of heavy metal (HM) accumulation, regarded as vital nutrients for plants, were detected in the following sequence: Zn > Mn/Cu > Fe. Conversely, toxic metals were found to be Cd/Cr > Ni > Pb, regardless of the type of vegetables. Principal Component Analysis (PCA) identified T8, T7, and T4 of TDW as the primary contributors to the accumulation of heavy metals in the vegetables examined. Furthermore, the analysis of the heavy metals revealed that the BCF, THQ, and HI values for all studied metals were below 1, except for Pb. This suggests that the present consumption rates of different leafy and non-leafy vegetables, whether consumed individually or together, provide a low risk in terms of heavy metal exposure. Nevertheless, the consumption of T8, T7, and T4 irrigated vegetables, specifically Indian spinach alone or in combination with red amaranth and radish, by both adults and children, at the recommended rate, was found to pose potential health risks. On the other hand, T2, T3, and T6 irrigated vegetables were deemed safe for consumption. These findings indicated that the practice of irrigating the vegetables with T8, T7, and T4 stages of TDW has resulted in a significant buildup of heavy metals in the soils and edible parts of vegetables which are posing health risks to adults and children. Hence, it is imperative to discharge the T8, T7, and T4 stages of TDW after ETP to prevent the contamination of vegetables and mitigate potential health risks.

Synergistic potential in spinel ferrite MFe2O4 (M = Co, Ni) nanoparticles-mediated graphene oxide: Structural aspects, photocatalytic, and kinetic studies

The existence of artificial dyes in water is a significant environmental concern, as it can lead to poor water quality. Photodegradation is becoming an increasingly popular method for treating water contaminated with dyes. In this study, the photodegradation of Reactive Red 66 and Reactive Red 120 dyes, as well as textile wastewater, was investigated under UV and visible light irradiation. To enhance the photoresponse of the MFe2O4 (M = Co, Ni) nanoparticles, modifications were made by incorporating graphene oxide. The MFe2O4 nanoparticles and MFe2O4/GO nanocomposite photocatalysts were subjected to several characterization techniques, including FT-IR, Raman spectroscopy, XRD, DRS, zeta potential, VSM, TGA, DSC, BET, SEM, and EDAX analysis. Experiments were conducted to optimize several key parameters involved in the photodegradation process, including pH, photocatalyst dosage, initial dye concentration, and irradiation time. The removal efficiency of Reactive Red 66 and Reactive Red 120 dyes using CoFe2O4 nanoparticles was found to be 86.97 and 82.63%, respectively. Also, the removal percentage of these dyes using CoFe2O4/GO nanocomposite photocatalyst was 95.57 and 90.9% for Reactive Red 66 and Reactive Red 120, respectively. Experiments found that NiFe2O4 nanoparticles removed 90.92% of Reactive Red 66 dye and 84.7% of Reactive Red 120 dye. The NiFe2O4/GO nanocomposite photocatalyst showed even higher removal efficiencies, degrading 97.96% of Reactive Red 66 and 93.44% of Reactive Red 120. After three days of exposure to visible light irradiation, the removal percentage of Reactive Red 66 using MFe2O4 and MFe2O4/GO nanocomposite was investigated.

Techno-environmental and economic assessment of color removal strategies from textile wastewater

The textile industry is one of the most chemical-intensive processes, resulting in the unquestionable pollution of more than a quarter of the planet's water bodies. The high recalcitrant properties of some these pollutants resulted on the development of treatment technologies looking at the larger removal efficiencies, due to conventional systems are not able to completely remove them in their effluents. However, safeguarding the environment also implies taking into account indirect pollution from the use of chemicals and energy during treatment. On the other hand, the emerged technologies need to be economically attractive for investors and treatment managers. Therefore, the costs should be kept under control. For this reason, the present study focuses on a comparative Life Cycle Assessment and Life Cycle Costing of four scale-up scenarios aiming at mono and di-azo reactive dyes removal from textile wastewater. Two reactors (sequencing batch reactor and two-phase partitioning) were compared for different reaction environments (i.e., single anaerobic and sequential anaerobic-aerobic) and conditions (different pH, organic loading rates and use of polymer). In accordance with the results of each scenario, it was found that the three technical parameters leading to a change in the environmental profiles were the removal efficiency of the dyes, the type of dye eliminated, and the pollutant influent concentration. The limitation of increasing organic loading rates related to the biomass inhibition could be overcame through the use of a novel two-phased partitioning bioreactor. The use of a polymer at this type of system may help restore the technical performance (84.5 %), reducing the toxic effects of effluents and consequently decreasing the environmental impact. In terms of environmental impact, this is resulting into a reduction of the toxic effects of textile effluents in surface and marine waters compared to the homologous anaerobic-aerobic treatment in a sequencing batch reactor. However, the benefits achieved for the nature comes with an economic burden related to the consumption of the polymer. It is expected that the cost of investment of the treatment with the two-phase partitioning bioreactor rises 0.6-8.3 %, depending on market prices, compared to the other analyzed sequential anaerobic-aerobic technologies. On the other side, energy and chemical consumption did not prove to be limiting factors for economic feasibility.

Hydrogen bond-mediated self-assembly of Tin (II) oxide wrapped with Chitosan/[BzPy]Cl network: An effective bionanocomposite for textile wastewater remediation

A novel and efficient bionanocomposite was synthesized by incorporating SnO into chitosan (Ch) and a room-temperature ionic liquid (RTIL). The bionanocomposite was synthesized in benzoyl pyridinium chloride [BzPy]Cl to maintain the unique properties of SnO, chitosan, and the ionic liquid. Adsorption and photodegradation processes were applied to evaluate the bionanocomposite for removing azo and anthraquinone dyes and textile wastewater. SnO/[BzPy]Cl and SnO/[BzPy]Cl/Ch samples were prepared and characterized using various techniques, including FT-IR, SEM, XRD, EDAX, XPS, DSC, TGA, nitrogen adsorption/desorption isotherm, and DRS analysis. SEM analysis revealed a hierarchical roughened rose flower-like morphology for the biocomposite. The band gap energies of SnO/[BzPy]Cl and SnO/[BzPy]Cl/chitosan were found to be 3.9 and 3.3 eV, respectively, indicating a reduction in the band gap energy with the introduction of [BzPy]Cl and chitosan. SnO/[BzPy]Cl/Ch showed high removal rates (92-95 %) for Fast Red, Blue 15, Red 120, Blue 94, Yellow 160, and Acid Orange 7 dyes. The adsorption kinetics followed a pseudo-second-order model. In addition, the effect of different photodegradation parameters such as solution pH, dye concentrations, contact time, and amount of photocatalyst, was studied. Given the optimal results obtained in removing azo and anthraquinone dyes, the SnO/[BzPy]Cl/Ch nanocomposite was used as an efficient nanocomposite for removing dyes from textile wastewater. The highest removal efficiency was found to be 95.8 %, obtained under ultraviolet and visible light. Furthermore, BOD and COD reduction analysis showed significant reductions, indicating the excellent performance of the photocatalyst.

New insights on the decolorization of waste flows by Saccharomyces cerevisiae strain - A systematic review

One of the common causes of water pollution is the presence of toxic dye-based effluents, which can pose a serious threat to the ecosystem and human health. The application of Saccharomyces cerevisiae (S. cerevisiae) for wastewater decolorization has been widely investigated due to their efficient removal and eco-friendly treatments. This review attempts to create an awareness of different forms and methods of using Saccharomyces cerevisiae (S. cerevisiae) for wastewater decolorization through a systematic approach. Overall, some suggestions on classification of dyes and related environmental/health problems, and treatment methods are discussed. Besides, the mechanisms of dye removal by S. cerevisiae including biosorption, bioaccumulation, and biodegradation and cell immobilization methods such as adsorption, covalent binding, encapsulation, entrapment, and self-aggregation are discussed. This review would help to inspire the exploration of more creative methods for applications and modification of S. cerevisiae and its further practical applications.

Clay-moringa seedcake composite for removal of cationic and anionic dyes

The present study investigated the potential of a composite prepared from kaolinite clay and moringa seedcake in removing methylene blue (MB) and acid orange-7 (AO-7) dyes from aqueous solutions using batch and column tests. The composite was modified using different chemicals during the synthesis process, and the composites were characterised using different techniques such as FTIR, SEM-EDS and XRD. Characterisation showed the presence of actively charged functional groups and porous structure on the composites prepared. Batch tests were performed to assess the effect of operating conditions such as adsorbent dosage, pH, initial dye concentration and contact time. NaOH-modified and H2SO4/NaOH-modified composites demonstrated the highest adsorption capacities for AO-7 and MB, respectively, and were selected for subsequent studies. The adsorption process of dye was best fitted by the Freundlich isotherm and pseudo-second-order kinetic models suggesting that the sorption of MB and AO-7 onto the composites is a heterogeneous, multilayer chemical adsorption process. Long-term fixed-column tests were conducted with the composites to assess the impact of flow rate, bed depth and initial dye concentration on the dye removal efficiency. Optimum removals of 86 and 94%, respectively at pH 2 and pH 10 were obtained for AO-7 and MB in batch tests, along with adsorption capacities of 205.65 and 230.49 mg/g for AO-7 and MB. Results from the column tests were best explained by the Clark model and the Bed Depth-Service Time model. Competing ions impacted the removal of AO-7, while no significant effect was found for MB. The composites could be reused up to four cycles without significantly affecting the adsorption capacity. The present study thus shows the potential of the composite for removal of both the dyes.

Denim industry wastewater treatment by a heterogeneous solar-Fenton process catalyzed by Fe supported on recycled polyethylene terephthalate (PET) by ultrasonic modification

The textile industry is an important economic sector; however, its wastewater generates a great impact on the environment. A heterogeneous solar Fenton (HSF) process was evaluated for denim wastewater treatment. The catalyst was obtained through ultrasonic modification of recycled polyethylene terephthalate (PET) with Fe nanoparticles (PET/NPs- Fe3O4). The SFH process was optimized using surface response methodology with a face-centered central composite design considering the effects of the hydraulic retention time (10, 25, and 40 min), hydrogen peroxide dosage (500, 1000, and 1500 mg/L), and mass of the packed catalyst (4, 6 and 8 g) on the color, COD, and turbidity removal efficiencies. The operating conditions for maximum COD removal were H2O2 541.7 mg/L, HRT 33.9 min, and PET/NPs- Fe3O4 dose 7.9 g with solar radiation. The removal of 91.2% COD, 86.2% color, 90.4% turbidity, and 81.9% TOC was obtained at 14.2 kJ/L QUva. PET modification yielded 1.6 mg Fe/g PET, and the modification method does not allow Fe leaching. The effluent obtained from the SFH process complies with the maximum permissible limits in Mexican legislation in terms of COD, TOC, turbidity, and color and allows the reuse of PET.

Mycoremediation of Industrial Textile Wastewater Using Ganoderma lucidum Pellets and Activated Dolomite in Batch Bioreactor

In the world of fast fashion, textile industries are blooming rapidly to meet the consumer's demands. However, vast amounts of wastewater have been constantly produced, and it is becoming a serious environmental problem in the waterways. Although the technology for treating textile wastewater has been well reported and established, more sustainable efforts have taken the attention nowadays. Through the use of living Malaysian Ganoderma lucidum mycelial pellets (GL) and activated dolomite (AD) in the treatment system, the study explores the synergy between biosorption and physisorption as alternative treatment for textile wastewater. In the current work, mixture of GL premixed with AD (50:50; v/v) is used to treat industrial textile wastewater. The morphology, adsorption characteristics, and antibacterial activity of the adsorbents were studied. The mixture of adsorbents is capable of removing colours by 77.8% and reducing chemical oxygen demand (COD) by 75% within 48 h contact. Furthermore, the kinetic and adsorption had been studied and follow the pseudo-first-order kinetic model while both adsorption of Langmuir and Freundlich model was deduced from the treatment. In addition, antimicrobial activities from the treatment potentially reduced 10 × 101 CFU/mL after 48 h. The synergistic treatment by Ganoderma lucidum mycelial pellets and activated dolomite has immense potential in future wastewater treatment technology to obtain cleaner water.

Appraising the phycoremediation potential of cyanobacterial strains Phormidium and Oscillatoria for nutrient removal from textile wastewater (TWW) and synchronized biodiesel production from TWW-tolerant biomass

In this study, phycoremediation of textile wastewater (TWW) by freshwater cyanobacterial strains such as sp., Oscillatoria sp. F01 and Oscillatoria sp. F02 was evaluated, and lipids were simultaneously extracted from biomass for biodiesel production. Onset of the study, Phormidium sp. and Oscillatoria sp. F01 has better growth rates, increased biomass production, high chlorophyll content, and efficient nutrient utilization in TWW compared to Oscillatoria sp. F02. Phormidium sp. showed 1.41 g/L dry weight, followed by Oscillatoria sp. F01 with 1.39 g/L and Oscillatoria sp. F02 with 1.02 g/L biomass. Both strains demonstrated their capability to elevate the pH level while reducing TDS and eliminating/reducing several nutrients such as nitrates, nitrites, phosphates, sulphates, sulphides, chlorides, calcium, sodium, and magnesium. Further, the total lipids extracted from the TWW-grown Phormidium sp., Oscillatoria sp. F01 and Oscillatoria sp. F02 was estimated to be 8.20, 13.70 and 11.20 %, respectively, on day 21, which was higher than the lipid content obtained from control cultures. Further, biodiesel produced from the lipids of all strains showed higher levels of C12:0, C16:0, C16:1, C18:1, C18:2, and C18:3 among all the fatty acids. Therefore, they can potentially offer a valuable source of lipids and diverse fatty acids for high-quality biodiesel production. This integrated system not only offers a solution for TWW treatment but also provides a feedstock for renewable fuel production simultaneously.

Treatment of textile wastewater using the Co(II)/NaHCO3/H2O2 oxidation system

Textile wastewater (TWW) is one of the most hazardous wastewaters for ecosystems when it is discharged directly into water streams without adequate treatment. Some organic pollutants, such as dyes in TWW, are considered refractory compounds that are difficult to degrade using conventional chemical and biological methods. The bicarbonate-activated peroxide (BAP) system is an advanced oxidation process (AOP) based on applying H2O2, which has been demonstrated to be a clean and efficient technology for dye degradation, with the advantage of operating under slightly alkaline pH conditions. In this study, response surface methodology (RSM) based on a central composite design (CCD) was used to optimize the degradation of TWW contaminated with the azo dye Acid Black 194 using the BAP system catalyzed with cobalt ions in solution (Co2+). The analysis of variance (ANOVA) technique was applied to identify significant variables and their individual and interactive effects on the degradation of TWW. The optimum reagent concentrations for degrading TWW at 25 °C and with 45 μM Co2+ were 787.61 and 183.34 mM for H2O2 and NaHCO3, respectively. Under these conditions, complete decolorization (≥99.40), 32.20 % mineralization, and 52.02 % chemical oxygen demand removal were achieved. Additionally, the acute toxicity of textile wastewater before and after oxidation was evaluated with guppy fish (Poecilia reticulata), showing a total reduction in mortality after treatment with the Co2+-BAP system. The Co2+-BAP oxidation system is a potential method for textile wastewater treatment, which, in addition to achieving complete decolorization and partial mineralization, improves biodegradability and reduces the toxicity of the treated water.

Comparative Sb(V) removal efficacy of different iron oxides from textile wastewater: effects of co-existing anions and dye compounds

Elevated Sb(V) concentration in textile wastewater is a growing environmental concern worldwide and has received wider attention in recent years. Iron oxides possess appealing characteristics as efficient and cost-effective adsorbents in large-scale applications. In the present study, Sb(V) adsorption capacity of α-Fe2O3, γ-Fe2O3, and Fe3O4 was compared under experimental conditions close to the practical textile wastewater treatment. Results demonstrated that α-Fe2O3 performed better under different pH values, reaction times, dye compounds, and co-existing ions as compared to γ-Fe2O3 and Fe3O4, and the adsorption equilibrium was achieved within 8 h. Sb(V) adsorption is found to be highly pH dependent, and higher removal was achieved in lower pH, indicating the involvement of electrostatic interactions. The pHpzc value of α-Fe2O3 was 7.15, which favored Sb(V) adsorption in practical wastewater having neutral pH value (pH ~ 7). Pseudo-first- and pseudo-second-order described the data and the simulated values of qe fitted well with the experimental values, indicating that pseudo-second-order model described the adsorption kinetics better with R2 (> 0.95) higher than of pseudo-first-order plots. The Langmuir and Freundlich models both described well the sorption data of all the adsorbents, where the R2 values were > 0.90 with a better fit in the Freundlich model for α-Fe2O3, suggesting that the adsorbent has heterogeneous surface characteristics. Similarly, characterizations revealed that the specific surface area, pore volume, and hydroxyl group content in α-Fe2O3 were higher than others, making it easier for contaminants to bind on to the active sites. Furthermore, the effect of dyes and co-existing anions on Sb(V) adsorption was negligible, except for SO42-, CO32-, and PO43- by the formation of inner-sphere complexes with iron oxides through competitive adsorption with [Sb(OH)6]-. Findings from the present study suggested that α-Fe2O3 effectively reduced Sb(V) in textile wastewater and could be a promising alternative for practical textile wastewater treatment.

Whole genome sequencing analysis and Box-Behnken design for the optimization of the decolourization of mixture textile dyes by halotolerant microbial consortium

The use of dyes in textile industries has resulted in substantially contaminated soil, water and ecosystem including fauna and flora. So, the application of eco-friendly approach for dyes removal is in great demand. The goal of this research was to develop and test a bacterial consortium for biodegrading dyes in artificial textile effluent (ATE) derived from mixture of Indigo carmine (40 mg/l); Malachite green (20 mg/l); Cotton bleu (40 mg/l); Bromocresol green (20 mg/l) and CI Reactive Red 66 (40 mg/l) dissolved in artificial seawater. The Box-Behnken design (BBD) which combine six variables with three levels each was used to determine the potential removal of dyes in ATE, by the selected microbial consortium (M31 and M69b). The experimental process indicated that decolourization of ATE reached 77.36 % under these conditions values: salinity (30 g/l), pH (9), peptone (5 g/l), inoculum size (1.5 108 CFU/ml), agitation (150 rpm) and contact time (72 h). The decolourization was confirmed by FTIR spectrum analysis of ATE before and after bacterial treatment. Bacterial strains used in this study were identified as Halomonas pacifica M31 and Shewanella algae M69b using 16 rDNA sequences. Moreover, the total genome analysis of M31 and M69b validated the implication of bacterial genes in mixture dyes removal. Therefore, the effect of the selected bacterial consortium on ATE removal was confirmed and it may be used in industrial wastewater treatment to issuing environmental safety.

Impact of salinity on anaerobic ceramic membrane bioreactor for textile wastewater treatment: Process performance, membrane fouling and machine learning models

Anaerobic membrane bioreactor (AnMBR) shows great potential for textile wastewater treatment, but high salinity in the influent may undermine its performance. This study evaluated the impact of salinity on the treatment performance of an upflow anaerobic sludge blanket (UASB) configured AnMBR using a flat sheet ceramic membrane. The salinity was stepwise increased (0, 5, 10 and 20 g/L) in four phases of the AnMBR operation. Results indicated that increased salinity jeopardized the COD removal efficiency of AnMBR from 92% to 73%, but had a marginal effect on dye removal efficacy (90-96%). Low salinity (5 g/L) boosted the biogas production whilst high salinity (>10 g/L) had a negative impact. Additionally, the increase of salinity resulted in the soluble microbial production (SMP) concentration soar and membrane fouling rate increase, peaking at a salinity of 10 g/L (Phase III) and recovering back to a lower level at a salinity of 20 g/L (Phase IV). This indicated a transition occurrence at a salinity of 10 g/L (Phase III). The microbial diversity analyses further suggested a transition from salinity-sensitive microbes (Aminiphilus, Caldatribacterium, Mesotoga, Methanobrevibacter, Methanobacterium, Methanosaeta) to salinity-tolerant microbes (Longilinea, Ignavibacterium, Rhodovarius, Bosea and Flexilinea). This transition can be associated with the increase SMP concentration and more severe membrane fouling in Phase III, which were mitigated after a new equilibrium was reached when the microbial consortium acclimatized to the high salinity. Finally, a machine learning model of the Adaboost algorithm was established to predict COD removal under different salinities. Importantly, this study revealed that AnMBR process performance and membrane operation can be maintained for high salinity textile wastewater treatment with a halophilic microbial community growth under high-salinity selection pressure.

Treatment of synthetic textile wastewater containing Acid Red 182 by electro-Peroxone process using RSM

The Azo dyes are primarily utilized in textile industries. Treatment of textile wastewater because of the presence of recalcitrant dyes using conventional processes is greatly challenging and ineffective. So far, no experimental work has been conducted on the decolorization of Acid Red 182 (AR182) in aqueous media. Hence, in this novel experimental work, the treatment of AR182 from the Azo dyes family was explored using the electro-Peroxone (EP) process. For the optimization of operating factors, including AR182 concentration, pH, applied current, and O3 flowrate in the decolorization of AR182, Central Composite Design (CCD) was utilized. The statistical optimization presented a highly satisfactory determination coefficient value and a satisfactory second-order model. The expected optimum conditions by the experimental design were as the following: AR182 concentration at 483.12 mg.L-1, applied current at 0.627,113 A, pH at 8.18284 and O3 flowrate at 1.13548 L min-1. The current density is directly proportional to dye removal. However, increasing the amount of applied current beyond a critical value has a contradictory impact on dye removal performance. The dye removal performance in both acidic and highly alkaline environments was negligible. Hence, ascertaining the optimum pH value and conduction of the experiment at that point is critical. At optimum points, the decolorization performance in predicted and experimental conditions for AR182 were 99 and 98.5%, respectively. The outcomes of this work clearly substantiated that the EP can be successfully utilized for the decolorization of AR182 in textile wastewater.

Synthesis and application of manganese-doped zinc oxide as a potential adsorbent for removal of Congo red dye from wastewater

Synthetic dyes are considered toxic compounds and as such are not easily removed by conventional water treatment processes. This study demonstrated the synthesis of pure and manganese- (Mn), silver- (Ag), and iron- (Fe) doped zinc oxide (ZnO) nanoparticles via the wet chemical route. In particular, it investigated the batch adsorption studies and physiochemical properties of synthesized pure and doped ZnO materials for removing toxic congo red (CR) dye. X-ray diffraction (XRD), Raman spectroscopy, and energy-dispersive X-ray spectroscopy (EDS) confirmed the synthesis of the pure and doped ZnO materials. The batch adsorption investigation revealed adsorption efficiencies of 99.4% for CR dye at an optimal dose of 0.03 g/30 ml for Mn-doped ZnO at a solution pH of 2. The adsorption capacity of each of the synthesized materials was found to be in order Mn-doped ZnO (232.5 mg/g) > Ag-doped ZnO (222.2 mg/g) > pure ZnO (212.7 mg/g) > Fe-doped ZnO (208.3 mg/g). Both pseudo-second-order kinetics model and the Langmuir isotherm model accurately explained the adsorption behaviors of CR dye. As such, Van der Waal interactions, H-bonding, and electrostatic interaction were found to be the adsorption mechanisms responsible for dye removal. In addition, the desorption-regeneration investigation indicated the successful reuse of the exhausted Mn-doped ZnO material for five cycles of CR dye adsorption with an efficiency of 83.1%. Overall, this study has demonstrated that Mn-doped ZnO could be considered a viable adsorbent for the cleanup of dye-contaminated water.

Energy-efficient reuse of bio-treated textile wastewater by a porous-structure electrochemical PbO2 filter: Performance and mechanism

In this work, a novel porous-structure electrochemical PbO2 filter (PEF-PbO2) was developed to achieve the reuse of bio-treated textile wastewater. The characterization of PEF-PbO2 confirmed that its coating has a variable pore size that increases with depth from the substrate, and the pores with a size of 5 μm account for the largest proportion. The study on the role of this unique structure illustrated that PEF-PbO2 possesses a larger electroactive area (4.09 times) than the conventional electrochemical PbO2 filter (EF-PbO2) and enhanced mass transfer (1.39 times) in flow mode. The investigation of operating parameters with a special discussion of electric energy consumption suggested that the optimal conditions were a current density of 3 mA cm-2, Na2SO4 concentration of 10 g L-1 and pH value of 3, which resulted in 99.07% and 53.3% removal of Rhodamine B and TOC, respectively, together with an MCETOC of 24.6%. A stable removal of 65.9% COD and 99.5% Rhodamine B with a low electric energy consumption of 5.19 kWh kg-1 COD under long-term reuse of bio-treated textile wastewater indicated that PEF-PbO2 was durable and energy-efficient in practical applications. Mechanism study by simulation calculation illustrated that the part of the pore of the PEF-PbO2's coating with small size (5 μm) plays an important role in this excellent performance which provides the advantage of rich ·OH concentration, short pollutant diffusion distance and high contact possibility.

Alginate-based porous polyHIPE for removal of single and multi-dye mixtures: Competitive isotherm and molecular docking studies

A novel hydrophilic porous alginate-based polyHIPE (AGA) was synthesized via an oil-in-water emulsion templating approach. AGA was used as an adsorbent for removing methylene blue (MB) dye in single- and multi-dye systems. BET, SEM, FTIR, XRD, and TEM were used to characterize AGA to elucidate its morphology, composition and physicochemical properties. According to the results, 1.25 g/L AGA adsorbed 99 % of 10 mg/L MB in 3 h in a single-dye system. The removal efficiency decreased to 97.2 % in the presence of 10 mg/L Cu2+ ions and 40.2 % when the solution salinity increased to 70 %. In a single-dye system, the experimental data do not match well with the Freundlich isotherm, pseudo-first order, and the Elovich kinetic model, however, in a multi-dye system, it fit well with both extended Langmuir and the Sheindorf-Rebhun-Sheintuch. Notably, AGA removed 66.87 mg/g in a dye solution containing only MB, whereas 50.14-60.01 mg/g adsorption of MB was accomplished in a multiple-dye system. According to the molecular docking analysis, the dye removal process involved chemical bonds between the functional groups of AGA and the dye molecules, hydrogen bonds, hydrophobic and electrostatic interactions. The overall binding score of MB decreased from -26.9 kcal/mol in a single-dye system to -18.3 kcal/mol in a ternary system.

Treatment of textile wastewater using carbon-based nanomaterials as adsorbents: a review

Waste derived from the textile industry can contain a wide variety of pollutants of organic and inorganic natures, such as dyes (e.g., acid, basic, reactive, mordant dyes) and toxic metals (e.g., lead, chromium, cadmium). The presence of pollutants at high concentrations in textile waste makes them relevant sources of pollution in the environment. To solve this problem, various technologies have been developed for the removal of pollutants from these matrices. Thus, adsorption emerges as an efficient alternative for textile waste remediation, providing advantages as simplicity of operation, economy, possibility of using different adsorbent materials, and developing on-line systems that allow the reuse of the adsorbent during several adsorption/desorption cycles. This review will initially propose an introduction to the adsorption world, its fundamentals, and aspects related to kinetics, equilibrium, and thermodynamics. The possible mechanisms through which a pollutant can be retained on an adsorbent will be explained. The analytical techniques that offer valuable information to characterize the solid phases as well as each adsorbate/adsorbent system will be also commented. The most common synthesis techniques to obtain carbon nano-adsorbents have been also presented. In addition, the latest advances about the use of these adsorbents for the removal of pollutants from textile waste will be presented and discussed. The contributions reported in this manuscript demonstrated the use of highly efficient carbon-based nano-adsorbents for the removal of both organic and inorganic pollutants, reaching removal percentages from 65 to 100%.

Use of life cycle assessment as a tool to evaluate the environmental impacts of textile effluents: a systematic review

The textile industry is known for its large consumption of water, energy, and chemical products, making it one of the most environmentally impactful activities. To measure these environmental impacts, life cycle analysis (LCA) is a powerful tool that considers the entire process, from the extraction of raw materials to the finalization of textile products. In this context, this work aimed to present a systematic study on the use of the LCA methodology in the environmental assessment of effluents from the textile industry. The survey for data was carried out using the Scopus and Web of Science databases, and the PRISMA method was utilized for organizing and selecting of articles. During the meta-analysis phase bibliometric and specific data were extracted from selected publications. For the bibliometric analysis, a quali-quantitative approach was adopted, and the VOSviewer software was employed. The review encompasses a total of 29 articles, which were published between 1996 and 2023.The majority of the reviewed articles have shown the use of the LCA as a supportive tool for optimization focusing on sustainability, comparing the environmental, economic, and technical aspects through different approaches. The findings revel that China has the highest number of authors among the selected articles, while researchers from France and Italy had the highest number of international collaborations. The ReCiPe and CML methods were the most frequently used for evaluating life cycle inventories, with global warming, terrestrial acidification, ecotoxicity, and ozone depletion being the main impact categories. The use of activated carbon in textile effluents treatment has shown to be promising since it is environmentally friendly.

Efficient microbial cellulose/Fe3O4 nanocomposite for photocatalytic degradation by advanced oxidation process of textile dyes

Fenton-type advanced oxidative processes (AOP) have been employed to treat textile dyes in aqueous solution and industrial effluent. The work focused on assisting the limitations still presented by the Fenton process regarding the use of suspended iron catalysts. Soon, a nanocomposite of bacterial cellulose (BC) and magnetite (Fe₃O₄) was developed. It has proven to be superior to those available in the literature, exhibiting purely catalytic properties and high reusability. Its successful production was verified through analytical characterization, while its catalytic potential was investigated in the treatment of different textile matrices. In initial tests, the photo-Fenton process irradiated and catalyzed by sunlight and BC/Fe₃O₄ discolored 92.19% of an aqueous mixture of four textile dyes. To improve the efficiency, the design of experiments technique evaluated the influence of the variables pH, [H₂O₂], and the number of BC/Fe₃O₄ membranes. 99.82% of degradation was obtained under optimized conditions using pH 5, 150 mg L^-1 of H₂O₂, and 11 composite membranes. Reaction kinetics followed a pseudo-first-order model, effectively reducing the organic matter (COD = 83.24% and BOD = 88.13%). The composite showed low iron leaching (1.60 ± 0.08 mg L^-1) and high stability. It was recovered and reused for 15 consecutive cycles, keeping the treatment efficiency at over 90%. As for the industrial wastewater, the photo-Fenton/sunlight/BC/Fe₃O₄ system showed better results when combined with the physical-chemical coagulation/flocculation process previously used in the industry's WWTP. Together they reduced COD by 77.77%, also meeting the color standards (DFZ scale) for the wavelengths of 476 nm (<3 m^-1), 525 nm (<5 m^-1), and 620 nm (<7 m^-1). Thus, the results obtained demonstrated that employing the BC/Fe₃O₄ composite as an iron catalyst is a suitable alternative to materials employed in suspension. This is mainly due to the high catalytic activity and power of reuse, which will reduce treatment costs.

Simultaneous photocatalytic removal of organic dye and heavy metal from textile wastewater over N-doped TiO2 on reduced graphene oxide

Methylene blue (MB) and hexavalent chromium Cr(VI) are hazardous pollutants in textile waste and cannot be completely removed using conventional methods. So far, there have been no specific studies examining the synthesis and activity of N-TiO₂/rGO as a photocatalyst for removing MB and Cr(VI) from textile wastewater. This work especially highlights the synthesis of N-TiO₂/rGO as a photocatalyst which exhibits a wider range of light absorption and is highly effective for simultaneous removal of MB-Cr(VI) under visible light. Titanium tetrachloride (TiCl₄) was used as the precursor for N-TiO₂ synthesis using the sol-gel method. Graphite was oxidized using Hummer's method and reduced with hydrazine to produce rGO. N-TiO₂/rGO was synthesized using a hydrothermal process and then analyzed using several characterization instruments. The X-ray diffraction pattern (XRD) showed that the anatase N-TiO₂/rGO phase was detected at the diffraction peak of 2θ = 25.60°. Scanning electron microscopy and transmission electron microscopy (SEM-EDS and TEM) dispersive X-ray spectrometry images show that N-TiO₂ particles adhere to the surface of rGO with uniform size and N and Ti elements are present in the N-TiO₂/rGO combined investigated. Gas absorption analysis data (GSA) shows that N-TiO₂/rGO had a surface area of 77.449 m²/g, a pore volume of 0.335 cc/g, and a pore size of 8.655 nm. The thermogravimetric differential thermal analysis (TG-DTA) curve showed the anatase phase at 500-780 °C with a weight loss of 0.85%. The N-TiO₂/rGO composite showed a good photocatalyst application. The photocatalytic activity of N-TiO₂/rGO for textile wastewater treatment under visible light showed higher effectiveness than ultraviolet light, with 97.92% for MB and 97.48% for Cr(VI). Combining N-TiO₂ with rGO is proven to increase the light coverage in the visible light region. Removal of MB and Cr(VI) can be carried out simultaneously and results in a removal efficiency of 95.96%.

Efficient detoxification of textile wastewater by applying Chenopodium album nanoparticles and its application in simulated metal-bearing effluents removal

Large-scale pollution of water and soils bodies is associated with the discharge of the untreated textile industry effluents. Halophytes grows on saline lands and accumulate secondary metabolites and other stress protective compounds. Utilization of Chenopodium album (halophytes) to synthesize zinc oxide (ZnO) and their efficiency to treat different concentrations of textile industry waste water is proposed in this study. Potential of nanoparticles textile industry waste water effluents was also analyzed by exposing different concentrations of nanoparticles (0 (control), 0.2, 0.5, 1 mg) and time intervals of 5, 10, and 15 days. The absorption peaks by UV region, FTIR and SEM analysis were used characterized on ZnO NPs for the first time. FTIR analysis showed the preens of various functional groups and vital phytochemicals that can play its role in the formation of nanoparticles that can be used for trace elements removal and bioremediation. SEM analysis indicated that the pure ZnO NPs synthesis ranged from 30 to 57 nm. Results shows that the green synthesis of halophytic nanoparticles presents maximum removal capacity after 15 days exposure to 1 mg of ZnO NPs. Hence, the prepared ZnO Nps from halophytes can be a viable solution for treating the textile industry effluents before they are discharged into water bodies for sustainable environmental growth and environmental safety.

Living membrane bioreactor for highly effective and eco-friendly treatment of textile wastewater

The treatability of synthetic textile wastewater containing model dyes, such as reactive black and direct black dye (25.0 ± 2.6 mg_dye/L), with chemical oxygen demand (COD, 1000 ± 113 mg/L), ammonia‑nitrogen (NH₃-N, 140 ± 97 mg/L) and sulphate ions (SO₄^2-, 1357 ± 10.86 mg/L) was investigated in this study using an innovative living membrane bioreactor (LMBR) using an encapsulated self-forming dynamic membrane (ESFDM). The key advantage of ESFDMBR is the self-forming of the biological filtering layer protected between two meshes of inert robust and inexpensive material. A laboratory scale bioreactor (BR) equipped with a filtering unit mounting polyester meshes with a pore size of 30 μm, operated at an influent flux of 30 LMH was thus used. After the formation of the biological living membrane (LM), the treatment significantly reduced COD and DOC concentrations to the average values of 34 ± 10 mg/L and 32 ± 7 mg/L, corresponding to reduction efficiencies of 96.0 ± 1.1 % and 94 ± 1.05 %, respectively. Throughout the LMBR operation, the colours were successfully removed from synthetic textile wastewater with an overall removal efficiency of about 85.0 ± 1.8 and 86.0 ± 1.9 % for direct and reactive dyes, respectively. In addition, the proposed system was also found effective in affording removal efficiency of ammonia (NH₃) of 97 ± 0.5 %. Finally, this treatment afforded circa 40.7 ± 5.8 % sulphate removal, with a final concentration value of 805 ± 78.61 mg/L. The innovative living membrane, based on an encapsulated self-forming dynamic membrane allows a prolonged containment of the membrane fouling, confirmed by investigating the concentration of membrane fouling precursors and the time-course variations of turbidity and transmembrane pressure (TMP). Those final concentrations of wastewater pollutants were found to be below the limits for admission of the effluents in public sanitation networks in Italy and Tunisia, as representative countries for the regulation in force in Europe and North Africa. In conclusion, due to the low costs of plant and maintenance, the simple applicability, the rapid online implementation, the application of LMBR results in a promising method for the treatment of textile wastewater.

Removal of methylene blue using MnO2@rGO nanocomposite from textile wastewater: Isotherms, kinetics and thermodynamics studies

In this study, the adsorptive removal of methylene blue dye, which is commonly used in textile industries, was investigated using the MnO₂@reduced graphene oxide (rGO) adsorbent. The sonication-assisted synthesis from rGO nanosheets and MnO₂ nanoparticles resulted to the MnO₂@rGO nanocomposite with improved physicochemical properties. The characterization results showed the improved surface area, porous structure and adsorption sites from the nitrogen adsorption-desorption studies, improved morphology from the Scanning Electron Microscope (SEM) and Transmission Electron Microscope (TEM) and the improved crystal structure from X-ray powder diffraction (XRD). The improved physicochemical properties on the MnO₂@rGO nanocomposite played a significant role in enhancing the dye removal in textile wastewater. The equilibrium experimental data was best described by the Langmuir isotherm model with a maximum adsorption capacity of 156 mg g^-1, suggesting a monolayer adsorption. The kinetic data best fitted the pseudo-second order kinetic model, suggesting a chemisorption adsorption process. The thermodynamic data (ΔG°, ΔH° and ΔS°) confirmed the feasibility, randomness and spontaneous nature of the adsorption process. The mechanism of adsorption involved the hydrogen bonding, π-π interactions and electrostatic interactions. The removal of methylene blue using MnO₂@rGO nanocomposite in spiked textile wastewater yielded a 98-99% removal. The method demonstrated competitiveness when compared with literature reported results, paving way for further investigations towards industrial scale applications.

Bacillus spizizenii DN and microbial consortia biostimulation followed by gamma irradiation for efficient textile wastewater treatment

Textile wastewater still poses a huge environmental problem due to its high water consumption and high effluent release that is full of toxic chemicals. In the present study, different approaches were studied to layout an operating procedure for textile wastewater treatment in order to obtain treated wastewater that is safe for non-potable uses. Our approach depended on (1) co-substrate to biostimulate indigenous microbial textile wastewater community by adding Tryptone Soy Broth (TSB) and TSB supplemented with 1% glucose, (2) co-culture (bioaugmentation) with Bacillus spizizenii DN cells (previously isolated, identified and characterized as efficient decolorizing bacteria), and (3) co-metabolites using Bacillus spizizenii DN metabolites. The obtained results show that using Bacillus spizizenii DN cells resulted in 97.78% decolorization while adding Bacillus spizizenii DN metabolites resulted in 82.92% decolorization, both after 48 h incubation under microaerophilic conditions. The phyla identified for all treatments were Bacteroidota, Firmicutes, and Proteobacteria. The dynamic changes in the bacteria showed that both Clostridium and Acinetobacter disappeared for co-substrate, co-culture, and co-metabolite cultures. While Alkalibacterium and Stenotrophomonas appeared after adding Bacillus spizizenii DN cells, Flavobacterium increased for co-substrate and co-metabolic cultures while iron reducing bacteria appeared only for co-metabolic cultures. The use of 25 kGy gamma irradiation as a sterilization dose post bioremediation ensured safe use of treated wastewater. This was confirmed by cytotoxicity assay; the obtained IC₅₀ tested on BJ fibroblasts obtained from skin showed that gamma irradiated treated wastewater are about 80.1% less toxic than non-irradiated treated wastewater. We conclude that (1) we can use combined bioaugmentation and biostimulation as initial steps for in situ bioremediation in collection tanks and that (2) the proposed protocol for bioremediation of industrial wastewater should be tailored based on the required application and level of safety needed for re-use.

Removal of COD and color from textile industrial wastewater using wheat straw activated carbon: an application of response surface and artificial neural network modeling

A novel approach has been undertaken wherein chemically modified wheat straw activated carbon (WSAC) as adsorbent is developed, characterized, and examined for the removal of COD and color from the cotton dyeing industry effluent. Thirty experimental runs are designed for batch reactor study using the central composite method (CCM) for optimizing process parameters, namely biochar dose, time of contact, pH, and temperature, for examining the effect on COD and color-removing efficiency of WSAC. The experimental data have been modeled using the machine learning approaches such as polynomial quadratic regression and artificial neural networks (ANN). The determined optimum conditions are pH: 7.18, time of contact: 85.229 min, adsorbent dose: 2.045 g/l, and temperature: 40.885 °C, at which the COD and color removal efficiency is 90.92 and 94.48%, respectively. The nonlinear pseudo-second order (PSO) kinetic model shows good coefficient of determination (R² ~ 1) values. The maximum adsorption capacity for COD and color by WSAC is at the pH of 7, the temperature of 40 °C, adsorbent dose of 2 g/l is obtained at the contact time of 80 min is 434.78 mg/g and 331.55 PCU/g, respectively. The COD removal and decolorization is more than 70% in the first 20 min of the experiment. The primary adsorption mechanism involves hydrogen bonding, electrostatic attraction, n-π interactions, and cation exchange. Finally, the adsorbent is environmentally benign and cost-effective, costing 16.66% less than commercially available carbon. The result of the study indicates that WSAC is a prominent solution for treating textile effluent. The study is beneficial in reducing the pollutants from textile effluents and increasing the reuse of treated effluent in the textile industries.

Enhancement of biogranules development using magnetized powder activated carbon

Biogranulation has emerged as a viable alternative biological wastewater treatment approach because of its strong biodegradability potential, toxicity tolerance, and biomass retention features. However, this process requires a long duration for biogranules formation to occur. In this study, magnetic powder activated carbon (MPAC) was used as support material in a sequencing batch reactor to enhance biogranules development for wastewater treatment. Two parallel SBRs (designated R1 and R2) were used, with R1 serving as a control without the presence of MPAC while R2 was operated with MPAC. The biodegradability capacity and biomass properties of MPAC biogranules were compared with a control system. The measured diameter of biogranules for R1 and R2 after 8 weeks of maturation were 2.2 mm and 3.4 mm, respectively. The integrity coefficient of the biogranules in R2 was higher (8.3%) than that of R1 (13.4%), indicating that the addition of MPAC improved the structure of the biogranules in R2. The components of extracellular polymeric substances were also higher in R2 than in R1. Scanning electronic microscopy was able to examine the morphological structures of the biogranules which showed there were irregular formations compacted together. However, there were more cavities situated in R1 biogranules (without MPAC) when compared to R2 biogranules (with MPAC). Dye removal reached 65% and 83% in R1 and R2 in the post-development stage. This study demonstrates that the addition of MPAC could shorten and improve biogranules formation. MPAC acted as the support media for microbial growth during the biogranulation developmental process.

Fabrication of high performance Ti/SnO2-Nb2O5 electrodes for electrochemical textile wastewater treatment

Textile wastewater contains many organic compounds and colors that affect aquatic life and human health when discharged into the environment. High coloration due to excess dyes entering the wastewater causes coloration to the receiving water stream, affects the photosynthesis process of aquatic species, and adversely affects the landscape. SnO₂-based electrodes have been extensively used in electrochemical water treatment, but their low durability decreases the pollutant treatment ability. Therefore, it is necessary to add another stable oxide to improve the performance and stability of SnO₂ electrodes. This study aims to fabricate Ti/SnO₂-Nb₂O₅ electrodes for the textile wastewater treatment using the electrochemical oxidation method. Different molar ratios of SnO₂:Nb₂O₅ coating were prepared using the sol-gel method and then coated on the Ti substrates for calcination in 60 min at 500 °C. Scanning electron microscopy (SEM), X-ray diffraction (XRD), Brunauer Emmett Teller (BET), and cyclic voltammetry (CV) were used to determine the surface and electrochemical properties of Ti/SnO₂-Nb₂O₅ electrodes. The SEM images show that SnO₂-Nb₂O₅ electrode surfaces have the appearance of typical cracking structures of mixed metal oxides electrodes. The XRD spectrum show the SnO₂ peaks of facet (110), (101), (200), (301), (321) and Nb₂O₅ peaks of facet (001), (002), (100), (101), (102) on Ti substrates. Furthermore, the specific surface area of the Ti/SnO₂-Nb₂O₅ electrode ranges from 37.354 m²/g (SnO₂:Nb₂O₅ = 9:1) to 71.885 m²/g (SnO₂:Nb₂O₅ = 1:9). The electrochemical properties of SnO₂:Nb₂O₅ electrodes showed high oxygen, chlorine evolution potential and high organic pollutant degradation in textile wastewater with COD removal at 83 %, decolorization at 74 % and the generation of many free radicals such as HO^•, H₂O₂, O₃, Cl₂. The results demonstrate that the Ti/SnO₂-Nb₂O₅ electrode with the mole ratio of 3:7 is the best in textile wastewater treatment with the longest service life (39 h).

Spectral change of dissolved organic matter after extracted by solid-phase extraction and its feasibility in predicting the acute toxicity of polar organic pollutants in textile wastewater

Spectroscopic parameters can be used as proxies to effectively trace the occurrence of organic trace contaminants, but their suitability for predicting the toxicity of discharged industrial wastewater with similar spectra is still unknown. In this study, the organic contaminants in treated textile wastewater were subdivided and extracted by four commonly-used solid-phase extraction (SPE) cartridges, and the resulting spectral change and toxicity of textile effluent were analyzed and compared. After SPE, the spectra of the percolates from the four cartridges showed obvious differences with respect to the substances causing the spectral changes and being more readily adsorbed by the WAX cartridges. Non-target screening results showed source differences in organic micropollutants, which were one of the main contributors leading to their spectral properties and spectral variations after SPE in the effluents. Two fluorescence parameters (C1 and humic-like) identified by the excitation emission matrix-parallel factor analysis (EEM-PARAFAC) were closely correlated to the toxicity endpoints for Scenedesmus obliquus (inhibition ratios of cell growth and Chlorophyll-a synthesis), which can be applied to quantitatively predict the change of toxicity effect caused by polar organic pollutants. The results would provide novel insights into the spectral feature analysis and toxicity prediction of the residual DOM in industrial wastewater.

New insights for tracking bacterial community structures in industrial wastewater from textile factories to surface water using phenotypic, 16S rRNA isolates identifications and high-throughput sequencing

Industrial wastewater can possibly change the microbial ecological environment. There are few studies that focus on the bacterial variety in textile wastewater effluents and after combination with domestic wastewater. Thus, this study aimed to determine dye degrading bacteria from textile wastewater and environmental water samples using cultural method followed by phenotypic using BIOLOG and genotypic identification (16S rRNA) for dye degrading isolates identifications. Moreover, the bacterial communities in three textile and four environmental samples using Illumina MiSeq high-throughput sequencing were investigated. The findings revealed that in textile water samples, the ratio of dye-degrading bacteria (DDB) to total bacterial counts (TBC) was 27%. The identified DDB genera by 16S rRNA based on the cultural approach were Citrobacter spp., Klebsiella spp., Enterobacter spp., Pseudomonas spp., and Aeromonas spp. Regarding to the metagenomics analyses, the environmental samples had 5,598 Operational Toxanomic Units (OTUs) more than textile wastewater samples (1,463 OTUs). Additionally, the most abundant phyla in the textile wastewater were Proteobacteria (24.45-94.83%), Bacteriodetes (0.5-44.84%) and Firmicutes (3.72-67.40%), while, Proteobacteria (30.8-76.3%), bacteroidetes (8.5-50%) and Acentobacteria (0.5-23.12%) were the most abundant phyla in the environmental samples. The maximum abundant bacteria at species level in environmental samples were Aquabacterium parvum (36.71%), Delftia tsuruhatensis (17.61%), Parabacteriodes chartae (15.39%) and Methylorubrum populi (7.51%) in El-Rahawy Drain water (RDW), River Nile water (RNW), wastewater (RWW) from WWTP in Zennin and El-Rahawy Drain sediment (RDS), respectively, whereas the maximum abundant bacteria at species level in textile wastewater were Alkalibacterium pelagium (34.11%), Enterobacter kobei (26.09%) and Chryseobacterium montanum (16.93%) in factory 1 (HBT) sample, SHB sample (before mixing with domestic wastewater) and SHB sample (after mixing with domestic wastewater), respectively. In conclusion, the microbial communities in textile wastewaters are similar to those in environmental samples at the phylum level but distinct at the genus and species levels because they are exposed to a wider range of environmental circumstances.

Enhancement of electrode properties using carbon dots functionalized magnetite nanoparticles for azo dye decolorization in microbial fuel cell

Technology integration of nanomaterials with microbial fuel cell (MFC) have led to simultaneous degradation of recalcitrant dyes and energy extraction from textile wastewater. Limited electron transfer capacity and hydrophobicity of electrode are the bottlenecks for enhancing the performance of MFC. Nanomaterials can provide surface functionalities for electron transfers and serve as catalyst for pollutant degradation. In this paper, magnetite nanoparticles functionalized with carbon dots (Fe₃O₄@CDs) were used to enhance the electron transfer capacity of the electrodes due to numerous surface-active functional groups of CDs and the reversible redox reaction of Fe²⁺/Fe³⁺. Polydopamine (PDA) was used as binder to coat Fe₃O₄@CDs onto the surface of carbon felt (CF) electrodes in a sono-chemical reaction, favoring to form biocompatible electrodes. Charge transfer resistance of Fe₃O₄@CDs@PDA-CF was 5.02Ω as compared to 293.34Ω of unmodified CF. Fe₃O₄@CDs@PDA-CF installed MFC could achieve almost 98% dye degradation efficiency within 48 h and 18.30 mW m^-2 power output as compared to 77% dye degradation and 0.34 mW m^-2 power output by unmodified CF electrode MFC. Moreover, metagenomic analysis of microbial consortia developed in Fe₃O₄@CDs@PDA-CF MFC showed enrichment of electrogenic and dye degrading microbial communities of Achromobacter. Delftia, Geobacter and Pseudomonas.

Broken into pieces: The challenges of determining sulfonated azo dyes in biological reactor effluents using LC-ESI-MS/MS analysis

Most studies on the biodegradation of textile azo dyes use color as parameter for measuring the efficiency of degradation. Although widely employed, spectrophotometric methods are susceptible to the interference of metabolites or degradation products from the biological treatment. We propose a method for determination of a model sulfonated azo dye (Direct Black 22, DB22) in wastewater using solid-phase extraction (SPE) and liquid chromatography - electrospray ionization tandem mass spectrometry (LC-ESI-MS/MS). MS analysis in negative electrospray ionization mode showed DB22 as the most abundant precursor ion, corresponding to [M-3Na + H]^2-, which yields two radical anions of m/z 370.1 and m/z 645 after MS/MS fragmentation by collision-induced dissociation (CID). Calibration curve presented adequate linearity and precision in the range of 120-1500 ng mL^-1, and recovery and detection limit were appropriate to the typically employed working concentrations. Nevertheless, we observed that standard heating of DB22 under alkaline conditions to simulate the production of wastewater during dye-baths resulted in loss of MS/MS signal, without affecting color. Further analysis showed that DB22 undergoes hydrolysis and does not remain unaltered in solution. Alternative methods of hydrolysis evaluated resulted in no MS/MS signal as well. SPE-LC-ESI-MS/MS analysis evidenced the structural change of DB22 in aqueous solution while the dyeing-capacity was preserved. This technique has also the potential of being tailored to consider the detection of the hydrolyzed fragments of azo dyes in wastewater for appropriate quantification, but it was not the scope of the current step of this research. Color remains as a more reliable parameter for monitoring azo compounds which are unstable in aqueous solution, while a more robust and holistic method needs to be developed for the speciation of the DB22 products of thermal hydrolysis.

Efficient removal of dyes from aqueous solutions using short-length bimodal mesoporous carbon adsorbents

Ordered mesoporous carbons (OMCs) with controlled mesopore lengths and volumes were synthesized and investigated to remove the model dye methylene blue (MB) from aqueous solutions. The pore size, specific surface area, pore volume, and pore length of OMCs (CMK-3, sCMK-3, and sCMK-5) were analyzed and benchmarked against commercial activated carbon (AC). CMK-3 and sCMK-3 had narrow pore size distributions (PSDs) centered at ∼4.4 nm, whereas the PSD of sCMK-5 was bimodal, derived from the same pores as CMK-3 (∼4.4 nm) and the inner diameter of the carbon nanotubes (∼5.8 nm). The pore length decreased from 743 nm for CMK-3 to 173 nm for sCMK-3 and 169 nm for sCMK-5, facilitating the MB accessibility and efficient utilization of internal mesopores. The MB adsorption on the prepared adsorbents was well described by a pseudo-second-order kinetic model (R² > 0.999), and the initial adsorption rate (h) on sCMK-5 was 34.07-fold faster than that on commercial AC. The Langmuir model adequately explained the equilibrium adsorption data, and the increase in the Langmuir maximal adsorption capacity (q_m) of the OMCs was proportional to the specific surface area. The MB adsorption on sCMK-5 was endothermic and spontaneous, and proceeded primarily through physical adsorption as well as chemisorption reacting with oxygen atoms in hydroxyl groups. The prepared adsorbents were also suitable for polishing textile wastewater containing color-causing substances along with the background organic matter. These OMCs are promising for treating wastewater as efficient adsorbents for large molecular pollutants such as dyes.

Hydroxyapatite@Mn-Fe composite as a reusable sorbent for removal of Nile blue dye and Cr(VI) from polluted water

In this study, hydroxyapatite@Mn-Fe composite was used as a novel adsorbent to eliminate Nile blue (NB) dye and hexavalent chromium ion (Cr(VI)) from aqueous media. Different analyses such as FTIR, Map, SEM, EDX, BET, and XRD were used to study the characteristics of the composite. The highest sorption efficiencies of Cr(VI) and NB at pH 2 and 10 were 97.63% and 98.83%, respectively, which are significant values. Equilibrium and kinetic studies of the sorption process showed that the Freundlich isotherm model and pseudo-second-order kinetic model can better describe the equilibrium and kinetic behavior of the sorption process. According to the Langmuir model, the maximum sorption capacities of NB dye and Cr(VI) ion using the hydroxyapatite@Mn-Fe composite were 0.259 and 0.938 mmol/g, respectively. Also, the results of the thermodynamic study showed that the sorption process is favorable (ΔS° =  - 34.2 kJ/mol·K for Cr(VI) and - 144.6 kJ/mol·K for NB), spontaneous (ΔG° < 0), and exothermic (ΔH° =  - 27.99 kJ/mol for Cr(VI) and - 64.2 kJ/mol for NB). Moreover, the desorption process of both contaminants using the hydroxyapatite@Mn-Fe composite showed that the H₂SO₄ solution with a concentration of 3 mol/L can remove both contaminants separately with the highest efficiency. Furthermore, the reusability study indicated that the composite can be used in five reuse cycles without significant decrease in its efficiency. Besides, the composite was able to eliminate color, turbidity, COD, and BOD₅ from the textile wastewater with removal efficiencies of 93.06, 81.61, 76.05, and 71.88%, respectively. To the best of our knowledge, hydroxyapatite@Mn-Fe composite was synthesized and used for the first time to remove Cr(VI) ions and NB dye. In general, the aforementioned composite is recommended for industrial wastewater treatment.

Column adsorption of biological oxygen demand, chemical oxygen demand and total organic carbon from wastewater by magnetite nanoparticles-zeolite A composite

Herein, magnetite nanoparticles (NPs), zeolite A and magnetite-zeolite A (MAGZA) composite was developed by green methods. The produced nanomaterials were characterized and the effect of process parameters such as flow rate, adsorbent bed height and adsorbate inlet concentration was evaluated for the removal of biological oxygen demand (BOD), chemical oxygen demand (COD) and total organic carbon (TOC) in a column. The characterization results demonstrated the successful synthesis of magnetite NPs, zeolite A and MAGZA composite. The performance of the MAGZA composite in the fixed-bed column was superior to zeolite A and magnetite NPs. The parametric influence indicates that an increase in bed height and a decrease in the flow rate and inlet adsorbate concentration improved the performance of the adsorption column. The adsorption column demonstrated maximum performance at a flow rate (4 mL/min), bed height (5 cm) and inlet adsorbate concentration (10 mg/L). Under these conditions, the highest percent removal of BOD, COD and TOC were 99.96, 99.88 and 99.87%. Thomas and Yoon-Nelson's model suitably fitted the breakthrough curves. After five reusability cycles, the MAGZA composite demonstrated removal percent of BOD (76.5%), COD (55.5%) and TOC (64.2%). The produced MAGZA composite effectively removed BOD, COD and TOC from textile wastewater in a continuous operating mode.

Performance of sulfur-based autotrophic denitrification process for nitrate removal from permeate of an MBR treating textile wastewater and concentrate of a real scale reverse osmosis process

Textile is one of the industrial sectors generating the highest amount of wastewater with various polluting substances. Lately, water reuse in textile industries, especially, with the reverse osmosis (RO) process following membrane bioreactor (MBR) treatment has been applied more commonly. In this study, an autotrophic sulfur-based denitrifying column performance was evaluated, for the first time, for nitrate reduction from permeate of a lab-scale MBR receiving real textile wastewater and from the concentrate stream of a real scale-RO plant used for recovering water from textile wastewater. Nitrate concentration in the MBR effluent and RO concentrate averaged 35 ± 3 and 12 ± 2 mg-N/L, respectively. With the sulfur-based column bioreactor, quite high (≥90%) denitrification performances were attained both for MBR effluent and RO concentrate up to nitrate loadings of 0.432 and 0.12 g-N/(L.d), respectively. COD present in wastewater was not utilized in the column bioreactor, which illustrates no or minimal contribution of heterotrophic denitrification. Alkalinity concentration in the wastewater was enough to buffer the acid formation during autotrophic denitrification. Sulfate was generated accompanied by nitrate reduction and sulfide was formed at low nitrate loadings. In the batch tests, the denitrification rates for the MBR effluent and RO concentrate were 0.31 and 0.28 g-N/(g-VSS.d), respectively, which were relatively higher than the ones observed for the synthetic nitrate-contaminated groundwater. Autotrophic sulfur-based denitrification is a promising and robust process alternative even for textile RO concentrate with high concentrations of salinity, non-biodegradable COD, and color.

Application of Salvinia sps. in remediation of reactive mixed azo dyes and Cr (VI) - Its pathway elucidation

The emerging industrialization has resulted in the rapid growth of textile industries across the globe. The presence of xenobiotic pollutants in textile wastewater threatens the ecosystem. Applying different microbes (bacteria, fungi & algae) has paved the way for phytoremediation - the eco-friendly, cost-effective method. The present study focuses on the phytoremediation of reactive dyes - Reactive red, Reactive Brown & Reactive Black and Cr (VI) in synthetic textile wastewater using Salvinia sps. The mixed azo dyes of each 100 mg/L showed decolourization of 75 ± 0.5% and 82 ± 0.5% of removal of 20 mg/L of Cr (VI) after eight days of incubation in a phytoreactor setup. Chlorophyll analysis revealed the gradual decrease in the photosynthetic pigments during the remediation. The degraded metabolites were analyzed using FT-IR and showed the presence of aromatic amines on day zero, which were converted to aliphatic amines on day four. The GC-MS analysis revealed the disruption of -NN- bond, rupture of -CN- bond, scission of -N-N-bond, and loss of -SO₃H from the Reactive Black dye leading to the formation of an intermediate p-Hydroxy phenylhydrazinyl. The rupture of Reactive red dye resulted in the formation of p-Hydrazinyl toluene sulphonic acid, Naphthyl amine -3,6-disulphonic acid and 8-Hydroxy Naphthyl amine -3,6-disulphonic acid. Decarboxylation, desulphonation, deoxygenation and deamination of Reactive Brown dye showed the presence of different metabolites and metabolic pathways were proposed for the reactive azo dyes which were phytoremediated.

Application of poly aluminum chloride and alum as catalyst in catalytic ozonation process after coagulation for the treatment of textile wastewater

Textile wastewater is ranked highly contaminated among all industrial waste. During textile processing, the consumption of dyes and complex chemicals at various stages makes textile industrial wastewater highly challenging. Therefore, conventional processes based on single-unit treatment may not be sufficient to comply with the environmental quality discharge standards and more stringent guidelines for zero discharge of hazardous chemicals (ZDHC). In this study, a novel approach was followed by recycling Poly aluminum chloride (PACl) and Alum as a catalyst for the first time in the catalytic ozonation treatment process leading to a nascent method after using them as a coagulant in Coagulation/Flocculation. In the current investigation, six different combinations were studied to remove turbidity, TSS, COD, BOD₅, color, and biodegradability (BOD₅/COD ratios) of wastewater. Moreover, Central Composite Design was implied using RSM in Minitab software. During the combination of treatment processes, it was found that the pre-coagulation/flocculation with coagulant PACl followed by post-catalytic ozonation with recycled PACl, a more effective treatment than others. The optimum R.E of turbidity, TSS, COD, and color were 84%, 86%, 89%, and 98%, respectively. Moreover, a decrease in toxicity and increase in biodegradability (BOD₅/COD ratio from 0.29 to 0.54) was observed as well. The electrical energy demand and operational costs of treatment processes were estimated and compared with other treatment processes.

Extraction, characterization, and biosurfactant properties of extracellular polymeric substance from textile wastewater activated sludge

Textile wastewater treatment generates sludge that needs to be disposed of safely. The cost of sludge management is 50% of the total treatment cost of the wastewater. To reduce the expense, the sludge can be repurposed as a valuable resource by extracting extracellular polymeric substance (EPS). EPS contains polysaccharides, proteins, and humic substances, which are surface-active substances that act as potential biosurfactants. In this study, we investigated sludges (sludge 1 and sludge 2) from two different textile industries for EPS production. The results showed a maximum EPS yield of 179 mg/g-activated sludge from the wastewater from sludge 2. The EPS from textile wastewater activated sludge had a protein/carbohydrate ratio of 0.27-0.56, lower than that of municipal activated sludge. This difference is due to variations in nitrogen/carbon ratio in these wastewaters. Based on the biosurfactant activity test, EPS from both textile wastewaters could lower the water surface tension to around 60 mN/m and emulsify olive oil better than Tween 20 and 80. However, only EPS from sludge 2 showed better xylene emulsification than EPS from sludge 1 due to the difference in humic acid content.

Optimization for minimizing the cost of ozonation of highly concentrated textile dyeing wastewater in a bubble column reactor

Ozonation is one of the advanced oxidation methods that provide effective decolorization and detoxification of the dyeing wastewater without causing any sludge formation. Despite being a good alternative to biodegradation, ozonation suffers from a high operating cost. This study conducted the ozonation process at high initial dye concentrations and optimized the process parameters (such as initial ozone concentration, initial dye concentration, and pH) to minimize the operating cost in terms of the overall power consumption of the process. The ozonation of Reactive Blue dye was performed in a bubble column reactor at various process conditions. A central composite design (CCD)-based response surface method (RSM) statistical tool was used to optimize the process. An empirical correlation for the specific power consumption (defined as electricity consumed per unit mass of dye removed from a unit volume of dyeing wastewater) was developed and verified. It was found that the specific power consumption during ozonation can be lowered significantly (by ~25-30%) if the dyeing water was treated at high initial dye concentrations.

A censorious review on the role of natural lignocellulosic fiber waste as a low-cost adsorbent for removal of diverse textile industrial pollutants

BACKGROUND

Textile industries produce fabricated colored products using toxic dyes and other harsh chemicals. It is the responsibility of the textile industries to treat and eliminate these hazardous pollutants. However, due to the growing population demand, the treatment of these hazardous effluents is ineffective and imposes the treatment cost over the end users. The release of partially treated effluents in the environment may cause a severe threat to the ecology and its biota. The critical objective is to treat textile effluents efficiently using agricultural natural fiber waste. Generation of agricultural lignocellulosic fibrous waste increases every year due to growing population demand. Its use in the modern world is limited due to synthetic products. An alternative has enumerated to avoid wastage of fibrous resources and its clean disposal.

OBJECTIVE

The main objective of this review paper discussed the feasibility of lignocellulosic fibers and other lignocellulosic materials as natural low-cost adsorbent.

METHODS

The literature study was performed using Web of Science and Scopus indexed journals. The main factors considered to increase the adsorption ability, including the types of lignocellulosic surface modification techniques were searched with utmost importance for quality results. Intending to summarize the literature survey and provide persuasive content, systematic review process was considered for this novel article.

RESULTS

Out of 230 valuable publications, 159 published articles were considered for the present study until March 2022. The articles surplus with factors affecting adsorption (pH, adsorption dosage, surface area, temperature, initial concentration, contact time, physical and chemical properties of pollutants) and surface modification techniques (physical, chemical, and biological) were considered for this manuscript.

CONCLUSION

Overall, the physical and chemical modification methods are widely used instead of biological methods due to various factors as discussed briefly. Furthermore, the finding of this article supports the fact that the fibrous by-product resources are wasted in various occasions due to the modern lifestyle. Even though there is evidential possibility to implement the low-cost adsorbents, the industries limit their application prospects due to existing technology and financial compromises.

Molecular transformations of dissolved organic matter during UV/O3-assisted membrane filtration of UASB-treated real textile wastewater

A ceramic membrane reactor (CMR) integrated with in-situ UV/O₃ was assessed for post-treatment of the effluent out of an up-flow anaerobic sludge blanket (UASB) reactor treating real textile wastewater, focusing on the transformation of dissolved organic matter (DOM). Fourier transform ion cyclotron resonance mass spectrometry (FTICR-MS) revealed the transformation of heteroatomic DOM containing S, N or both to simpler DOM containing mainly C, H, and O atoms. The decreased N contents in products (N/C = 0.0249) compared to precursors (N/C = 0.0311) and the higher O/C ratios in the N-containing products suggest the removal of R-NH₂ groups accompanying DOM oxidation. While, S-containing compounds in the products had lower O/C and H/C ratios, suggesting a reduced state and the transformation of R-SO₃ to R-S-R. H-abstraction and OH addition were identified as the primary oxidation mechanisms, thus enhancing the dominance of highly unsaturated and phenolic DOM in the effluent (70.3%) compared to the feed (56.6%). The double bond equivalent (DBE) was also increased by 26% in the effluent compared to the feed and by 33% in products compared to precursors. These findings help understand the DOM transformation in UV/O₃-assisted ceramic membrane reactors and call for comprehensive toxicity analyses of effluents from the advanced oxidation processes.

Positively charged membranes for dye/salt separation based on a crossover combination of Mannich reaction and prebiotic chemistry

With the advent of increasingly loose nanofiltration membranes for dye desalination, synthesis methods based on interfacial polymerization and bio-inspired materials such as polydopamine (pDA) have been investigated. However, the long polymerization time of pDA greatly limits the synthesis and application of fast dye/salt separation membranes. In this work, prebiotic chemistry-inspired aminomalononitrile (AMN) was used as a binder to co-deposit the Mannich reaction of tetrakis(hydroxymethyl)phosphonium chloride (THPC) and polyethyleneimine (PEI) to form the positively charged selective layer rapidly. The optimum membrane had a water permeance of 30.7 LMH bar^-1 and a rejection of positively charged Victoria blue B (VBB, 200 ppm) and Na₂SO₄ (1 g/L) of 99.5 % and 9.9 %, respectively. Moreover, the results of a practical application test showed that it had excellent separation performance towards various positively charged dyes and salts. In addition, the actual application test results show that the membrane has good long-term stability during application. In terms of antifouling and antibacterial, the membrane has excellent antibacterial and antifouling properties., Further antibacterial tests were carried out, and the inactivation effect of the membrane on E. coli was also confirmed. The preparation method proposed in this work provides technical support for developing new dye/salt separation membranes.

Application of QSAR for investigation on coagulation mechanisms of textile wastewater

Coagulation is an effective preliminary treatment process for textile wastewater. In order to evaluate the effectiveness of the coagulation process, we performed quantitative structure activity relationship (QSAR) analyses with total organic carbon (TOC) removal rates (R_exp) as an index by three different coagulants (AlCl₃, FeCl₃, and MgCl₂). The experimental results showed that the average R_exp of the three coagulants was 39.12% ± 2.60%, 51.60% ± 2.88%, and 49.95% ± 3.17%. Subsequently, 42 molecular descriptors of dye molecules were calculated by quantitative calculation softwares Gaussian 09, Material Studio 7.0, and Multiwfn 3.7, and then QSAR models were constructed by a multiple linear regression (MLR) method for the three coagulation systems. The developed QSAR models demonstrated excellent stability, robustness, and predictability with values of R² = 0.7677, 0.8015, and 0.7035, Q²_INT = 0.6067, 0.7026, and 0.5898, Q²_EXT = 0.5505, 0.5076, and 0.5697, respectively. Based on the analysis of quantum parameters, the coagulation mechanism for AlCl₃, FeCl₃ is primarily electrostatic adsorption as well as hydrogen bonding, while MgCl₂ coagulates dyes mainly by electrostatic adsorption. This study provides an assessment of the removal rules and a feasible method for predicting dye removal rates in AlCl₃, FeCl₃, and MgCl₂ coagulation process.

Application of hybrid electrocoagulation and electrooxidation process for treatment of wastewater from the cotton textile industry

The hybrid electrocoagulation-electrooxidation (EC-EO) process was evaluated for its capability to remove color, total organic carbon (TOC), and chemical oxygen demand (COD). Aluminum (Al/Al) and iridium dioxide-coated onto titanium (IrO₂/Ti) electrodes were selected as anode/cathode for EC and EC-EO experiments, respectively. The box-Behnken statistical experimental design was used to optimize different operating conditions of the processes. The selected EC operating parameters are the concentrated dye concentration, applied current density, electrolysis time, and pH. The three chosen operating conditions for hybrid EC- EO processes are applied current density, pH, and electrolysis time. The results were evaluated based on the interaction effects of operating parameters of the treatment methods on the percentage of COD, TOC, and color removal. The EC process achieved 89% color and 76% COD removal rate at the optimum operating conditions. Likewise, the hybrid EC-EO process obtained 97% COD and color removal efficiency. FT-IR and ¹H and ¹³C NMR spectroscopy combined approach was employed to analyze the dye degradation extent. Both analysis results confirm the complete degradation of the organic contaminants into carbon dioxide and water. Thus, this study discloses that the treatment method using mesh IrO₂/Ti electrodes is a promising technology that could reach the discharge limit for industrial effluents. In addition, the optimum operating conditions are tested for real industrial wastewater effluents and show excellent performance in removing pollutants. Furthermore, the treatment method's mineralization study and economic analysis were performed and compared to other studies.