Determination of nitrite in food samples by anodic voltammetry using a modified electrode

Simultaneous determination of Cu2+, Zn2+, Cd2+, Hg2+ and Pb2+ by using second-derivative spectrophotometry method

A new method of simultaneous determination of Cu2+, Zn2+, Cd2+, Hg2+ and Pb2+ is proposed here by using the second-derivative spectrophotometry method. In pH=10.35 Borax-NaOH buffer, using meso-tetra (3-methoxyl-4-hydroxylphenyl) porphyrin ([T-(3-MO-4-HP)P]) as chromomeric reagent, micelle solution was formed after Tween-80 surfactant was added into the solution containing Cu2+, Zn2+, Cd2+, Hg2+ and Pb2+ ions. The original absorption spectrum of the above complexes was obtained after heating in the boiling water for 25 min. The second-derivative absorption peaks of five metal-porphyrin complexes can be separated from the original absorption spectrum by using chemometric tool. In this way, Cu2+, Zn2+, Cd2+, Hg2+ and Pb2+ ions can be determined simultaneously. Under the optimal conditions, the linear ranges of the calibration curve were 0-0.60, 0-0.60, 0-0.40, 0-0.80 and 0-0.48 μg mL(-1) for Cu2+, Zn2+, Cd2+, Hg2+ and Pb2+, respectively. The molar absorptivity of these color systems were 1.38×10(5), 1.01×10(5), 3.24×10(5), 1.07×10(5) and 1.29×10(5)Lmol(-1)cm(-1). The method developed in this paper has advantages in selectivity, sensitivity, operation and can effectively resolve spectra overlapping problem. This method has been applied to determine the real samples with satisfactory results.

Sensitivity and selectivity determination of BPA in real water samples using PAMAM dendrimer and CoTe quantum dots modified glassy carbon electrode

Bisphenol A (BPA) is an environmental pollutant to disrupt endocrine system or cause cancer, thus the detection of BPA is very important. Herein, an amperometric sensor was fabricated based on immobilized CoTe quantum dots (CoTe QDs) and PAMAM dendrimer (PAMAM) onto glassy carbon electrode (GCE) surface. The cyclic voltammogram of BPA on the sensor exhibited a well-defined anodic peak at 0.490V in 0.1M pH 8.0 PBS. The determination conditions were optimized and the kinetic parameters were calculated. The linear range was 1.3 x 10(-8) to 9.89 x 10(-6)M with the correlation coefficient of 0.9999. The limit of detection was estimated to be 1 x 10(-9)M. The current reached the steady-state current within about 5s. Furthermore, the fabricated sensor was successfully applied to determine BPA in real water samples.

Polymeric membrane electrodes with high nitrite selectivity based on rhodium(III) porphyrins and salophens as ionophores

Several porphyrin and salophen complexes with Rh(III) are examined as ionophores to prepare nitrite selective polymeric membrane electrodes. All ionophores tested exhibit preferred selectivity toward nitrite anion. Enhanced potentiometric nitrite selectivity is observed in the presence of either lipophilic anionic as well as cationic sites within the membranes, suggesting that the ionophores can function via either a charged or a neutral carrier response mechanism. Among a range of complexes and membrane formulations examined, optimal nitrite selectivity and reversible response down to 5 x 10(-6) M is achieved using Rh(III)-tetra(t-butylphenylporphyrin) as the ionophore in the presence of lipophilic cationic sites in plasticized poly(vinyl chloride) membrane. Response times are substantially longer than typical membrane electrodes apparently because of a slow nitrite ligation reaction with Rh(III); however, a significant improvement in dynamic EMF response can be realized by optimizing the membrane formulation and increasing the temperature. The selectivity observed with these membranes is greater than the best nitrite selective electrodes reported to date in the literature based on lipophilic Co(III)-corrin complexes, allowing the new nitrite electrodes to be utilized to determine the level of nitrite in meats with good correlation to the colorimetric Griess assay method.