Electronic conduction above 4 K of slightly reduced oxygen-deficient rutile TiO2-x

Combinatorial Approach to the Study of Particle Size Effects in Electrocatalysis: Synthesis of Supported Gold Nanoparticles

A high-throughput method for physical vapor deposition has been applied to the synthesis of libraries of supported gold particles on amorphous substoichiometric TiO(x)() and carbon supports. The TiO(x)() substrate stoichiometry can be varied or kept constant across a supporting sample, and subsequent deposition of particle sizes on supports are controlled through the nucleation and growth process. TEM measurements indicate nucleation and growth of Au particles takes place, with the smallest particles initially observed at 1.4 nm with a maximum density of 5.5 x 10(12) cm(-2) on titania, and 2.6 nm with concomitantly lower density on carbon. The 1.4-nm particles on titania exhibit a binding energy shift in the Au(4f) core level of 0.3 eV from bulk gold, and the shift is approximately 0.1 eV by the time particles grow to a mean size of 2.5 nm. These shifts are associated with final state effects, and the supported gold particles are metallic and appear to be relatively stable in air. When combined with appropriate substrates and screening techniques, this method provides a highly controllable method for the high-throughput synthesis of model supported catalyst.

Synthesis and Characterization of Ultrahigh Crystalline TiO2 Nanotubes

Ultrahigh crystalline TiO2 nanotubes were synthesized by hydrogen peroxide treatment of very low crystalline titania nanotubes (TiNT-as prepared), which were prepared with synthesized TiO2 nanoparticles by hydrothermal methods in an aqueous NaOH solution. Thus, prepared ultrahigh crystalline TiO2 nanotubes (TiNT-H2O2) showed comparable crystallinity with high crystalline TiO2 nanoparticles. The details of nanotubular structures were elucidated by high resolution-transmission electron microscopy (HR-TEM), field emission-scanning electron microscopy (FE-SEM), energy-dispersive X-ray analysis in transmission electron microscopy (TEM-EDX), X-ray diffraction (XRD), photoluminescence (PL), and BET surface area. TiNT-H2O2 was found to be a multiwalled anatase phase only with an average outer diameter of approximately 8 nm and an inner diameter of approximately 5 nm and grown along the [001] direction to 500-700 nm long with an interlayer fringe distance of ca. 0.78 nm. The photocatalytic activity of TiNT-H2O2 was about 2-fold higher than those of TiNT-as prepared, synthesized TiO2 nanoparticles, and TiO2-P25 (Degussa) in the photocatalytic oxidation of trimethylamine gas under UV irradiation.

Charge Trapping and Photoadsorption of O2 on Dehydroxylated TiO2 Nanocrystals—An Electron Paramagnetic Resonance Study

The interaction of photogenerated charges with molecular oxygen was investigated on TiO2 nanocrystals by means of paramagnetic resonance (EPR) spectroscopy. Compared to photoactivation experiments in vacuum at P < 10(-6) mbar and T = 140 K, the presence of O2 enhances the concentration of persistently trapped electron and hole centres--by a factor of ten--due to the formation of adsorbed O2- species. The photoadsorption of oxygen was also tracked quantitatively by pressure measurements, and the number of trapped charges, hole centres and O2- was found to correspond to ten electron-hole pairs per TiO2 nanocrystal. Conversely, in experiments at P < 10(-6) mbar with one trapped electron-hole pair per particle, charge separation is not persistent and completely reversible with respect to temperature. Heating to 298 K causes the total annihilation of photogenerated and trapped charges.

Monitoring Hole Trapping in Photoexcited TiO2(110) Using a Surface Photoreaction

The hole-induced photodesorption of chemisorbed O2 from a TiO2(110) single crystal has been employed to monitor the kinetics of electron-hole pair (e-h) formation and hole trapping. Excitation is produced by 3.4 +/- 0.05 eV photons at 110 K. Two separate O2 desorption processes have been found which are characteristic of low photon fluxes and high photon fluxes. At a critical photon flux, Fhnu(crit), the slow O2 photodesorption process suddenly converts to a fast process, signaling the saturation of hole traps in the TiO2 crystal. Consequently, this allows photogenerated holes to more efficiently reach the surface, causing more rapid O2 photodesorption. The estimated bulk concentration of hole traps is approximately 2.5 x 10(18) cm(-3), involving a fraction of about 3 x 10(-5) of the atomic sites in the bulk. Both the slow and fast O2 photodesorption processes are described by a rate law that is proportional to Fhnu(1/2), indicating that the steady-state concentration of holes, [h], is governed by second-order e-h pair recombination kinetics. Effective use is made of a hole scavenger molecule, adsorbed methanol (CH3OH), to probe the role of added hole traps on the rate of the photodesorption of adsorbed O2 molecules and on the magnitude of Fhnu(crit).

Photooxidation of Acetone on TiO2(110): Conversion to Acetate via Methyl Radical Ejection

It is generally held that radicals form and participate in heterogeneous photocatalytic processes on oxide surfaces, although understanding the mechanistic origins and fates of such species is difficult. In this study, photodesorption and thermal desorption techniques show that acetone is converted into acetate on the surface of TiO2(110) in a two-step process that involves, first, a thermal reaction between acetone and coadsorbed oxygen to make a surface acetone-oxygen complex, followed second by a photocatalytic reaction that ejects a methyl radical from the surface and converts the acetone-oxygen complex into acetate. Designation of the photodesorption species to methyl radicals was confirmed using isotopically labeled acetone. The yield of photodesorbed methyl radicals correlates well with the amount of acetone depleted and with the yield of acetate left on the surface, both gauged using postirradiation temperature programmed desorption (TPD). The thermal reaction between adsorbed acetone and oxygen to form the acetone-oxygen complex exhibits an approximate activation barrier of about 10 kJ/mol. A prerequisite to this reaction is the presence of surface Ti3+ sites that enable O2 adsorption. Creation of these sites by vacuum reduction of the surface prior to acetone and oxygen coadsorption results in an initial spike in the acetone photooxidation rate, but replenishment of these sites by photolytic means (i.e., by trapping excited electrons at the surface) appears to be a slow step in a sustained reaction. Evidence in this study for the ejection of organic radicals from the surface during photooxidation catalysis on TiO2 provides support for mechanistic pathways that involve both adsorbed and nonadsorbed species.

Electron transfer-induced dynamics of oxygen molecules on the TiO2(110) surface

Diffusion of oxygen molecules on transition metal oxide surfaces plays a vital role for the understanding of catalysis and photocatalysis on these materials. By means of time-resolved scanning tunneling microscopy, we provide evidence for a charge transfer-induced diffusion mechanism for O2 molecules adsorbed on a rutile TiO2(110) surface. The O2 hopping rate depended on the number of surface donors (oxygen vacancies), which determines the density of conduction band electrons. These results may have implications for the understanding of oxidation processes on metal oxides in general.