In vitroevaluation of the implant abutment connection sealing capability of different implant systems

Micro-leakage at the implant-abutment interface with different tightening torques in vitro

Objectives

This study evaluated the microleakage at the implant/abutment interface of external hexagon (EH) implants and abutments with different amounts of bacteria and tightening torques.

Material and Methods

A bacterial suspension was prepared to inoculate the implants. The first phase of this study used nine EH implants and abutments that were divided into three groups with different amounts of bacterial suspension (n=3): V0.5: 0.5 µL; V1.0: 1.0 µL e V1.5: 1.5 µL, and tightened to the manufacturer's recommended torque. The second phase of this experiment used 27 assemblies that were similar to those used in the first phase. These samples were inoculated with 0.5 µL of bacterial suspension and divided into three groups (n=9). T10: 10 Ncm; T20: 20 Ncm and T32: 32 Ncm. The samples were evaluated according to the turbidity of the broth every 24 hours for 14 days, and the bacteria viability was tested after that period. The statistical evaluation was conducted by Kruskal-Wallis testing (p<.05).

Results

During the first phase, groups V1.0 and V1.5 was presented with bacterial contamination in all samples after 24 h. During the second phase, two samples from group T10 and one from T20 presented positive results for bacterial contamination. Different amounts of bacterial solution led to overflow and contamination during the first 24 h of the experiment. The tightening torques did not statistically affect the microleakage in the assemblies. However, the group that was tightened to 32 Ncm torque did not show any bacterial contamination.

Conclusion

After 14 days of experimentation, the bacteria were proven to remain viable inside the implant internal cavity.

The cross-pin retained implant supported restoration: a study of gasket placement and leakage

BACKGROUND

Advantages of cross-pin retained implant supported restorations (ISRs) include predictable retrieval and predictable retention. Unlike direct to fixture (DTF) or cement retained restorations, the prosthetic design of a cross-pinned restoration retains gaps at the interfaces between the crown, abutment and cross-pin screw. These spaces permit leakage into the suprastructure and gasket placement has been recommended to prevent this leakage.

METHODS

Five different gaskets were assessed for their ability to prevent leakage into a cross-pinned ISR. The gaskets tested were: cement admixture on the cross-pin screw; cement admixture on the inner surface of the coping and the cross-pin screw; cement admixture on the inner surface of the coping only; cement admixture placed 1 mm from the margin of the coping and a filler placed in the abutment chimney. results: Only gaskets which sealed both the cross-pin screw interface and the abutment-crown interface prevented leakage. A filler placed in the abutment chimney prevented leakage into this space but did not prevent fluid accumulating between the coping and abutment. Conservative placement of cement at the margin of the coping failed to prevent leakage.

CONCLUSIONS

Cement gaskets may effectively prevent leakage into a cross-pinned ISR. However, the use of a cement as a gasket has to be weighed against the issue of predictable retrieval, cement extrusion and incomplete seating.

Sealing Capability and SEM Observation of the Implant-Abutment Interface

To evaluate the sealing capability of external hexagon implant systems and assess the marginal fit, two groups (n = 10 each) were employed: SIN (Sistema de Implantes Nacional, Brazil) and Osseotite, (Biomet 3i, USA). Sealing capability was determined by placing 0.7 μL of 1% acid-red solution in the implant wells before the torque of their respective abutments. Specimens were then placed into 2.5 mL vials filled with 1.3 mL of distilled water with the implant-abutment interface submerged. Three samples of 100 μL water were collected at previously determinate times. The absorbance was measured with a spectrophotometer, and the data were analyzed by Two-way ANOVA (P < .05) and Tukey's test. Marginal fit was determined using SEM. Leakage was observed for both groups at all times and was significantly higher at 144 hrs. SEM analysis depicted gaps in the implant-abutment interface of both groups. Gaps in the implant-abutment interface were observed along with leakage increased at the 144 hrs evaluation period.

Development of a new quantitative gas permeability method for dental implant-abutment connection tightness assessment

Background

Most dental implant systems are presently made of two pieces: the implant itself and the abutment. The connection tightness between those two pieces is a key point to prevent bacterial proliferation, tissue inflammation and bone loss. The leak has been previously estimated by microbial, color tracer and endotoxin percolation.

Methods

A new nitrogen flow technique was developed for implant-abutment connection leakage measurement, adapted from a recent, sensitive, reproducible and quantitative method used to assess endodontic sealing.

Results

The results show very significant differences between various sealing and screwing conditions. The remaining flow was lower after key screwing compared to hand screwing (p = 0.03) and remained different from the negative test (p = 0.0004). The method reproducibility was very good, with a coefficient of variation of 1.29%.

Conclusions

Therefore, the presented new gas flow method appears to be a simple and robust method to compare different implant systems. It allows successive measures without disconnecting the abutment from the implant and should in particular be used to assess the behavior of the connection before and after mechanical stress.

In vitro synchrotron-based radiography of micro-gap formation at the implant-abutment interface of two-piece dental implants

Micro-gap formation at the implant-abutment interface of two-piece dental implants was investigated in vitro using high-resolution radiography in combination with hard X-ray synchrotron radiation. Images were taken with the specimen under different mechanical loads of up to 100 N. The aim of this investigation was to prove the existence of micro-gaps for implants with conical connections as well as to study the mechanical behavior of the mating zone of conical implants during loading. Synchrotron-based radiography in comparison with classical laboratory radiography yields high spatial resolution in combination with high contrast even when exploiting micro-sized features in highly attenuating objects. The first illustration of a micro-gap which was previously indistinguishable by laboratory methods underlines that the complex micro-mechanical behavior of implants requires further in vitro investigations where synchrotron-based micro-imaging is one of the prerequisites.