Thermoanalytical, spectroscopic, and morphological study of poly(ethylene glycol)/poly(2-acrylamido-2-methylpropanesulfonic acid-co-N-isopropylacrylamide) semi-interpenetrating network gels

Enhancing Anode-Free Battery Performance with Self-Healing Single-Ion Conducting PAMPS-co-PBA Copolymer Interfaces

The design of anode-free batteries presents an attractive approach to the lithium metal battery. However, challenges such as uneven plating of lithium and poor Coulombic efficiency limit their commercially viable applications. In response to these challenges, this study introduces poly{(2-acrylamido-2-methylpropanesulfonic acid)-co-(butyl acrylate)} (PAMPS-co-PBA), an artificial interface engineered to enhance the cyclic stability of batteries by fortifying the solid electrolyte interphase (SEI) and enabling self-healing and single-ion conductivity. Synthesis outcomes, validated by FTIR and 1H NMR spectra, demonstrate successful production of PAMPS-co-PBA. Experimental results, including analyses of surface morphology, tensile strength, and Li plating/stripping tests, demonstrate the effectiveness of PAMPS-co-PBA in preventing dendrite formation and achieving >99% Coulombic efficiency. SEM analysis reveals better surface morphology and minimal lithium deposits for PAMPS-co-PBA compared with bare copper and other alternative interfaces. XPS analysis confirms the self-healing and single-ion conducting attributes of PAMPS-co-PBA postcycling. Density functional theory calculations elucidates the interface's behavior, confirming a pathway for Li-ion movement facilitated by the sulfonic acid group. Ab initio molecular dynamics simulations highlight the potential for SEI formation, shedding light on the influence of LiTFSI on interface protection. Anode-free full cell testing demonstrates PAMPS-co-PBA enhancement in stability over bare copper, with 1.6 times capacity retention over 50 cycles, primarily attributed to self-healing and dendrite suppression. Nonetheless, observed capacity fading after prolonged cycling suggests the optimization of Li salt choice. Overall, PAMPS-co-PBA presents a promising solution for enhancing battery performance through advanced interface engineering.

Dual-Modal Memory Enabled by a Single Vertical N-Type Organic Artificial Synapse for Neuromorphic Computing

Complementary neural network circuits combining multifunctional high-performance p-type with n-type organic artificial synapses satisfy sophisticated applications such as image cognition and prosthesis control. However, implementing the dual-modal memory features that are both volatile and nonvolatile in a synaptic transistor is challenging. Herein, for the first time, we propose a single vertical n-type organic synaptic transistor (VNOST) with a novel polymeric organic mixed ionic-electronic conductor as the core channel material to achieve dual-modal synaptic learning/memory behaviors at different operating current densities via the formation of an electric double layer and the reversible ion doping. As a volatile synaptic device, the resulting VNOST demonstrated an unprecedented operating current density of MA cm-2. Meanwhile, it is capable of 150 analog states, symmetric conductance modulation, and good state retention (100 s) for a nonvolatile synapse. Importantly, the artificial neural networks (ANNs) for recognition accuracy of the handwritten digital data sets recognition rate up to 94% based on its nonvolatile feature. This study provides a promising platform for building organic neuromorphic network circuits in complex application scenarios where high-performing n-type organic synapse transistors with dual-mode memory characters are necessitated.

A smart hydrogel carrier for silver nanoparticles: an improved recyclable catalyst with temperature-tuneable catalytic activity for alcohol and olefin oxidation

Radical polymerization reactions were employed to synthesize thermo-responsive poly(N-isopropylacrylamide-co-2-acrylamido-2-methyl-1-propanesulfonic acid) hydrogels at room temperature.

Preparations of Tough and Conductive PAMPS/PAA Double Network Hydrogels Containing Cellulose Nanofibers and Polypyrroles

To afford an intact double network (sample abbr.: DN) hydrogel, two-step crosslinking reactions of poly(2-acrylamido-2-methylpropanesulfonic acid) (i.e., PAMPS first network) and then poly(acrylic acid) (i.e., PAA second network) were conducted both in the presence of crosslinker (N,N'-methylenebisacrylamide (MBAA)). Similar to the two-step processes, different contents of 2,2,6,6-tetramethyl-1-piperidinyloxy (TEMPO) oxidized cellulose nanofibers (TOCN: 1, 2, and 3 wt.%) were initially dispersed in the first network solutions and then crosslinked. The TOCN-containing PAMPS first networks subsequently soaked in AA and crosslinker and conducted the second network crosslinking reactions (TOCN was then abbreviated as T for DN samples). As the third step, various (T-)DN hydrogels were then treated with different concentrations of FeCl3(aq) solutions (5, 50, 100, and 200 mM). Through incorporations of ferric ions into (T-)DN hydrogels, notably, three purposes are targeted: (i) strengthen the (T-)DN hydrogels through ionic bonding, (ii) significantly render ionic conductivity of hydrogels, and (iii) serve as a catalyst for the forth step to proceed with in situ chemical oxidative polymerizations of pyrroles to afford polypyrrole-containing (sample abbr.: Py) hydrogels [i.e., (T-)Py-DN samples]. The characteristic functional groups of PAMPS, PAA, and Py were confirmed by FT-IR. Uniform microstructures were observed by cryo scanning electron microscopy (cryo-SEM). These results indicated that homogeneous composites of T-Py-DN hydrogels were obtained through the four-step process. All dry samples showed similar thermal degradation behaviors from the thermogravimetric analysis (TGA). The T2-Py5-DN sample (i.e., containing 2 wt.% TOCN with 5 mM FeCl3(aq) treatment) showed the best tensile strength and strain at breaking properties (i.e., σTb = 450 kPa and εTb = 106%). With the same compositions, a high conductivity of 3.34 × 10-3 S/cm was acquired. The tough T2-Py5-DN hydrogel displayed good conductive reversibility during several "stretching-and-releasing" cycles of 50-100-0%, demonstrating a promising candidate for bioelectronic or biomaterial applications.

Clopidogrel eluting electrospun polyurethane/polyethylene glycol thromboresistant, hemocompatible nanofibrous scaffolds

Biomaterials used as blood-contacting material must be hemocompatible and exhibit lower thrombotic potential while maintaining hemostasis and angiogenesis. With the aim of developing thromboresistant, hemocompatible nanofibrous scaffolds, polyurethane/polyethylene glycol scaffolds incorporated with 1, 5, and 10 wt% Clopidogrel were fabricated and evaluated for their physiochemical properties, biocompatibility, hemocompatibility, and antithrombotic potential. The results of physicochemical characterization revealed the fabrication of nanometer-sized scaffolds with smooth surfaces. The incorporation of both polyethylene glycol and Clopidogrel to polyurethane enhanced the hydrophilicity and water uptake potential of polyurethane/polyethylene glycol/Clopidogrel scaffolds. The dynamic mechanical analysis revealed the enhancement in mechanical strength of the polyurethane/polyethylene glycol scaffolds on incorporation of Clopidogrel. The polyurethane/polyethylene glycol/Clopidogrel scaffolds showed a tri-phasic drug release pattern. The results of hemocompatibility assessment demonstrated the excellent blood compatibility of the polyurethane/polyethylene glycol/Clopidogrel scaffolds, with the developed scaffolds exhibiting lower hemolysis, increased albumin and plasma protein adsorption while reduction in fibrinogen adsorption. Further, the platelet adhesion was highly suppressed and significant increase in coagulation period was observed for Clopidogrel incorporated scaffolds. The results of cell adhesion and cell viability substantiate the biocompatibility of the developed nanofibrous scaffolds with the HUVEC cell viability on polyurethane/polyethylene glycol, polyurethane/polyethylene glycol/Clopidogrel-1, 5, and 10% at day 7 found to be 12.35, 13.36, 14.85, and 4.18% higher as compared to polyurethane scaffolds, and the NIH/3T3 cell viability found to be 35.27, 70.82, 36.60, and 7.95% higher as compared to polyurethane scaffolds, respectively. Altogether the results of the study advocate the incorporation of Clopidogrel to the polyurethane/polyethylene glycol blend in order to fabricate scaffolds with appropriate antithrombotic property, hemocompatibility, and cell proliferation capacity and thus, might be successfully used as antithrombotic material for biomedical application.

Functionalization of PVA to synthesize p-vinyl benzene sulfonate terpolymers – a comparative study of anticorrosion, adsorption and activation properties of the terpolymers on mild steel in 1 M HCl

Two water soluble terpolymers viz. PVA-AAm-PVBS and PVA-AA-PVBS were synthesized and characterized by FTIR, NMR, TGA and DSC.

Surface modification of silicate glass using 3-(mercaptopropyl)trimethoxysilane for thiol-ene polymerization

A thiol-ene polymerization was accomplished on silicate glass slides to graft a series of homopolymers and copolymers using 3-(mercaptopropyl)trimethoxysilane (MTS) as both a silane coupling agent and initiator. MTS was initially covalently bonded to an acid cleaned glass surface via a classical sol-gel reaction. Poly(acrylic acid) (PAA), poly(acrylamide) (PAAm), poly(methyl acrylate) (PMA), poly(acrylamido-2-methyl-propanesulfonic acid) (PAMPS), and the copolymer poly(AA-co-AAm-co-MA-co-AMPS) were grafted from the thiol group of MTS. The surface chemistry of the MTS modified slides and polymer grafts was characterized with attenuated total reflection Fourier transform infrared (ATR-FTIR) spectroscopy and X-ray photoelectron spectroscopy (XPS). Surface texture was evaluated with tapping mode atomic force microscopy (TM-AFM). The Owens-Wendt-Kaelble (OWK) and Lifshitz-van der Waals acid-base (LW-AB) methods were used to evaluate surface energies by sessile drop contact angle method. The synthetic approach demonstrated a facile, rapid method for grafting to glass surfaces.