Preparation and characterization of dual responsive sodium alginate-g-poly(vinyl alcohol) hydrogel

Construction and characterization of sodium alginate/polyvinyl alcohol double-network hydrogel beads with surfactant-tailored adsorption capabilities for efficient tetracycline hydrochloride removal

The extensive use of tetracycline (TC) for disease control and the residuals in wastewater has resulted in the spread and accumulation of antibiotic resistance genes, posing a severe threat to the human health and environmental safety. To solve this problem, a series of double-network hydrogel beads based on sodium alginate and polyvinyl alcohol were constructed with the introduction of various surfactants to modulate the morphology. The results showed that the introduction of surfactants can modulate the surface morphology and internal structure, which can also regulate the adsorption ability of the hydrogel beads. The SDS-B beads with SDS as surfactant exhibited highest adsorption efficiency for removal of TC with a maximum adsorption capacity up to 121.6 mg/g, which possessed a resistance to various cations and humic acid. The adsorption mechanism revealed that the superior adsorption performance of the hydrogel beads was primarily attributed to hydrogen bonding, electrostatic attraction, and π-π EDA interactions. Adsorption kinetics demonstrated that the pseudo-second-order model fitted the adsorption process well and adsorption isotherm showed the adsorption of TC occurred through both chemical and physical interactions. Moreover, the adsorption efficiency remained approximately 87.5 % after three adsorption-desorption cycles, which may have potential application and practical value in TC adsorption.

Tri-modified ferric alginate gel with high regenerative properties catalysts for efficient degradation of rhodamine B

Water pollution caused by dyes has become a focal point of attention. Among them, the heterogeneous Fenton reaction has emerged as an effective solution to this problem. In this study, we designed a ferric alginate gel (PAGM) tri-modified with poly(vinyl alcohol), graphene oxide, and MoS2 as a heterogeneous Fenton catalyst for organic dye degradation. PAGM addresses the drawbacks of alginate gel, such as poor mechanical properties and gel chain dissolution, thereby significantly extending the catalyst's lifespan. The removal rate of rhodamine B by PAGM reached 95.5 % within 15 min, which was 5.9 times higher than that of unmodified ferric alginate gel. Furthermore, due to the π-π interactions, PAGM exhibits unique adsorption properties for pollutants containing benzene rings. Additionally, PAGM can be regenerated multiple times through a simple soaking procedure without any performance degradation. Finally, the reaction column constructed with PAGM maintained an 83.5 % removal rate even after 319 h of continuous wastewater treatment. This work introduces a novel concept for the study of alginate-based gel catalysts in heterogeneous Fenton reactions.

An ion-coordination hydrogel based sensor array for point-of-care identification and removal of multiple tetracyclines

Misuse and overuse of tetracycline antibiotics (TCs) brings serious issues to ecological environment, food safety and human health. It is urgent to develop unique platform for high efficient identification and removal of TCs. In the present investigation, an effective and simple fluorescence sensor array was constructed based on the interaction between metal ions (Eu³⁺ and Al³⁺) and antibiotics. Benefiting from the different affinities between the ions and TCs, the sensor array can identify TCs from other antibiotics, which also can further differentiating four kinds of TCs (OTC, CTC, TC and DOX) from each other via linear discriminant analysis (LDA) technique. Meanwhile, the sensor array performed well in quantitative analysis of single TC antibiotic and differentiation of TCs mixtures. More interestingly, Eu³⁺ and Al³⁺-doped sodium alginate/polyvinyl alcohol hydrogel beads (SA/Eu/PVA and SA/Al/PVA) were further constructed, which can not only identify the TCs but simultaneously remove the antibiotics with high efficiency. The investigation provided an instructive way for rapid detection and environment protection.

Strong adsorption properties and mechanism of action with regard to tetracycline adsorption of double-network polyvinyl alcohol-copper alginate gel beads

In the present study, glutaraldehyde was used as a hydrophobic modifier to crosslink polyvinyl alcohol (PVA), and copper ion was immobilized by sodium alginate (SA). Polyvinyl alcohol-copper alginate (PVA-CA) gel beads were prepared by a one-step process, and were used to adsorb and remove tetracycline (TC) from an aqueous solution. The beads were characterized by scanning electron microscopy (SEM), thermogravimetric analysis (TGA), Brunauer-Emmett-Teller (BET) measurement, X-ray diffraction (XRD), energy dispersive spectroscopy (EDS), and Fourier transform infrared spectroscopy (FTIR). The adsorption experiment showed that the optimal pH value of the beads was 5, and that their adsorption met pseudo-second-order kinetic and Langmuir isothermal models. The adsorption thermodynamics experiment showed that the adsorption process was spontaneous and endothermic. Under optimal adsorption conditions, the maximum adsorption capacity for TC of the beads was 231.431 mg/g, which was much higher than that of a single copper alginate matrix. After 5 adsorption-desorption cycles, the adsorption capacity remained high. FTIR and X-ray photoelectron spectroscopy (XPS) revealed that the cation bonding bridge reaction was the main driving force behind the adsorption mechanism. Compared with other reported adsorption materials, the PVA-CA gel beads have high adsorption capacity, a simple preparation process, and excellent recovery performance.

A poly(vinyl alcohol)/sodium alginate blend monolith with nanoscale porous structure

A stimuli-responsive poly(vinyl alcohol) (PVA)/sodium alginate (SA) blend monolith with nanoscale porous (mesoporous) structure is successfully fabricated by thermally impacted non-solvent induced phase separation (TINIPS) method. The PVA/SA blend monolith with different SA contents is conveniently fabricated in an aqueous methanol without any templates. The solvent suitable for the fabrication of the present blend monolith by TINIPS is different with that of the PVA monolith. The nanostructural control of the blend monolith is readily achieved by optimizing the fabrication conditions. Brunauer Emmett Teller measurement shows that the obtained blend monolith has a large surface area. Pore size distribution plot for the blend monolith obtained by the non-local density functional theory method reveals the existence of the nanoscale porous structure. Fourier transform infrared analysis reveals the strong interactions between PVA and SA. The pH-responsive property of the blend monolith is investigated on the basis of swelling ratio in different pH solutions. The present blend monolith of biocompatible and biodegradable PVA and SA with nanoscale porous structure has large potential for applications in biomedical and environmental fields.

Recent advances on the development of wound dressings for diabetic foot ulcer treatment--a review

Diabetic foot ulcers (DFUs) are a chronic, non-healing complication of diabetes that lead to high hospital costs and, in extreme cases, to amputation. Diabetic neuropathy, peripheral vascular disease, abnormal cellular and cytokine/chemokine activity are among the main factors that hinder diabetic wound repair. DFUs represent a current and important challenge in the development of novel and efficient wound dressings. In general, an ideal wound dressing should provide a moist wound environment, offer protection from secondary infections, remove wound exudate and promote tissue regeneration. However, no existing dressing fulfills all the requirements associated with DFU treatment and the choice of the correct dressing depends on the wound type and stage, injury extension, patient condition and the tissues involved. Currently, there are different types of commercially available wound dressings that can be used for DFU treatment which differ on their application modes, materials, shape and on the methods employed for production. Dressing materials can include natural, modified and synthetic polymers, as well as their mixtures or combinations, processed in the form of films, foams, hydrocolloids and hydrogels. Moreover, wound dressings may be employed as medicated systems, through the delivery of healing enhancers and therapeutic substances (drugs, growth factors, peptides, stem cells and/or other bioactive substances). This work reviews the state of the art and the most recent advances in the development of wound dressings for DFU treatment. Special emphasis is given to systems employing new polymeric biomaterials, and to the latest and innovative therapeutic strategies and delivery approaches.