Investigation of the decomplexation of polyamide/ CaCl 2 complex toward a green, nondestructive recovery of polyamide from textile waste

Recycling and Degradation Pathways of Synthetic Textile Fibers such as Polyamide and Elastane

Synthetic textile production is a major contributor to global waste growth, a phenomenon exacerbated by population growth and increased consumption. Global fiber production is expected to reach 147 million tons by 2030. New insights into recycling solutions are being developed. For example, progress has been made in recycling fibers such as polyester, including polyethylene terephthalate (PET), through the use of enzymes that can break specific bonds and return the material to its original state. However, this process must be carried out according to the nature of the polymer in question. In addition, the mixing of different synthetic fibers and the use of dyes make it difficult to develop a complete recycling process that separates the fibers and returns them to their original raw material. This review focuses on two types of fibers widely used in the textile industry, Nylon or polyamide (PA) and elastane (Spandex or Lycra), and explores the challenges and opportunities associated with their recycling.

Three-Dimensionally Printed Ternary Composites of Polyamide: Effect of Gradient Structure on Dimensional Stability and Mechanical Properties

Fused deposition modeling (FDM) 3D printing has the advantages of a simple molding principle, convenient operation, and low cost, making it suitable for the production and fabrication of complex structural parts. Moving forward to mass production using 3D printing, the major hurdle to overcome is the achievement of high dimensional stability and adequate mechanical properties. In particular, engineering plastics require precise dimensional accuracy. In this study, we overcame the issues of FDM 3D printing in terms of ternary material compounds for polyamides with gradient structures. Using multi-walled carbon nanotubes (MWCNTs) and boron nitride (BN) as fillers, polyamide 6 (PA6)-based 3D-printed parts with high dimensional stability were prepared using a single-nozzle, two-component composite fused deposition modeling (FDM) 3D printing technology to construct a gradient structure. The ternary composites were characterized via DSC and XRD to determine the optimal crystallinity. The warpage and shrinkage of the printed samples were measured to ensure the dimensional properties. The mechanical properties were analyzed to determine the influence of the gradient structures on the composites. The experimental results show that the warpage of pure polymer 3D-printed parts is as high as 72.64%, and the introduction of a gradient structure can reduce the warpage to 3.40% by offsetting the shrinkage internal stress between layers. In addition, the tensile strength of the gradient material reaches up to 42.91 MPa, and the increasing filler content improves the interlayer bonding of the composites, with the bending strength reaching up to 60.91 MPa and the interlayer shear strength reaching up to 10.23 MPa. Therefore, gradient structure design can be used to produce PA6 3D-printed composites with high dimensional stability without sacrificing the mechanical properties of PA6 composites.

Eco-friendly dyeing of polyamide and polyamide-elastane knits with living bacterial cultures of two Streptomyces sp. strains

Given the environmental burden of textile industry, especially of dyeing processes and the volume of synthetic dyes and surfactants, the intensive development of the greener approaches is under way. Herein, an environmentaly-friendly dyeing of polyamide (PA) and PA/Elastane (PA/EA) knits using live bacterial approach in water environment, completely eliminating usage of textile auxiliaries is described. A total of 12 pigment-producing Streptomyces strains were isolated and purified from soil and rizoshere or bark of smoke tree Cotinus coggygria samples. The antibacterial, antifungal and cytotoxic effects of crude bacterial extracts were tested. Antimicrobial effect was obtained by the majority of extracts but only two streptomycetes extracts, 11-5 and BPS51, showed moderate cytotoxicity against HaCaT human cell line. This was the reason to select 11-5 and BPS51 strains for the dyeing of the textile materials. Excellent properties of dyeing wool, silk and PA are achieved initially using live cultures, and the bioprocess is optimized on commercial PA and PA/EA knits used for stockings production. Satisfactory coloration of both knits is achieved with dynamic conditions (culture shaking at 180 rpm over 5-14 days at 30 ºC) giving the best coloration results, except in the case of the PA sample dyed with a bacterial strain 11-5. The prolongation of dyeing time leads to higher color yields independently of fabric and bacteria strain. Although the color differences between the samples before and after washing are observed, washing fastness after three washing cycles can be considered as satisfactory.