Cellulose nanofibers-based composite film with broadening MXene layer spacing and rapid moisture separation for humidity sensing and humidity actuators

Based on the basic idea of expanding the interlayer spacing of MXene, utilizing the effect of gallic acid-modified cellulose nanofibers for rapid moisture separation, the flexible sensing and driving composite film with a perfect balance among humidity signal response and mechanical properties was prepared. Inspired by the stacking of autumn fallen leaves, the cellulose nanofibers-based composite films were formed by self-assembly under vacuum filtration of blending gallic acid-modified cellulose nanofibers with MXene. The enhanced mechanical properties (tensile strength 131.1 MPa, puncture load 0.88 N, tearing strength 165.55 N/mm, and elongation at break 16.14 %), humidity sensing (the stable induced voltage 63.7 mV and response/recovery time 3.2/5.1 s), and humidity driving (154.7° bending angle) properties were observed. The synergistic effect of hydrogen bonds, the "pinning effect" arising from the side chains, and the hierarchical layered microstructure contributed to the enhanced performance. This work exemplifies the application of green natural product for preparing intelligent sensing, wearable devices, and biomimetic robots.

Hydrophobic modification of cellulose nanofibers by gallic acid and the application in pressure sensing

Via rational molecular structure design and using gallic acid (GA) for hydrophobic modification of cellulose nanofibers (CNF), the "polymer dipole" CNF-GA with hydrophilic main chains and hydrophobic side chains was prepared, which improved the poor piezoelectric properties of CNF used for preparing pressure sensors. Due to the appearance of the side chains, the elongation at break of the CNF-GA-2, compared with CNF, was enhanced by 186 %, and the excellent tensile strength, puncture load, and tearing strength were displayed. Moreover, the significant glass transition temperature (Tg) near the human body temperature was exhibited for CNF-GA, making it possible to be applied in temperature sensing. Most importantly, the CNF-GA-2 showed the maximum hydrophobicity, with a contact angle of 76.77°. Finally, the CNF-GA-2/MXene nanocomposite film was prepared by the CNF-GA-2 with MXene through vacuum filtration. The results indicated that the film had excellent piezoelectric properties (d33 = 63.283), the generated stable induced voltage (125.6 mV), the preferable piezoresistive performance (ΔR/R0 = 2.15), the fast response/recovery time (48/61 ms), which could achieve dynamic and static responses. Moreover, this film could be used for real-time detection of limb movements (such as wrists).

Synthesis and Characterization of Poly(Butylene Sebacate-Co-Terephthalate) Copolyesters with Pentaerythritol as Branching Agent

Poly(butylene sebacate-co-terephthalate) (PBSeT) copolyesters are prepared by melt polymerization via two-step transesterification and polycondensation using pentaerythritol (PE) as a branching agent. The effects of the incorporated PE on its chemical, thermal, mechanical, and degradation properties, along with the rheological properties of its melt, are investigated. The highest molecular weight and intrinsic viscosity along with the lowest melt flow index were achieved at a PE content of 0.2 mol%, with minimal reduction in the tensile strength and the highest tear strength. The addition of PE did not significantly influence the thermal behavior and stability of the PBSeT copolyesters; however, the elongation at break decreased with increasing PE content. The sample with 0.2 mol% PE exhibited a higher storage modulus and loss modulus as well as a lower loss angle tangent than the other samples, indicating improved melt elasticity. The incorporation of more than 0.2 mol% PE enhanced the enzymatic degradation of copolyesters. In summary, including within 0.2 mol%, PE effectively improved both the processability-related characteristics and degradation properties of PBSeT copolyesters, suggesting their potential suitability for use in agricultural and packaging materials.