Repeatability and reproducibility of variable flip angle T 1 quantification in the prostate at 3 T

Anatomical zone and tissue type impacts the repeatability of quantitative MRI parameters and radiomic features for longitudinal monitoring of treatment response in the prostate

OBJECTIVE

To (1) establish the repeatability coefficient (%RC) of region of interest (ROI) and voxel-wise measurements of a comprehensive range of quantitative MRI (qMRI) parameters and radiomic features in the prostate, and (2) assess the impact of different tissue types (benign vs tumor) and anatomical zones (peripheral, PZ, and non-peripheral, nPZ) on the %RCs.

METHODS

Test-retest qMRI was acquired in ten prostate cancer patients and six healthy volunteers. Parametric maps of apparent diffusion coefficient (ADC), diffusion coefficient (D), perfusion fraction (f), hypoxia score (HS), longitudinal relaxation time (T1), and observed transverse relaxation rate (R2*) were calculated. Fifty-nine radiomic feature maps were calculated from each of the parametric maps and T2-weighted images. The %RCs between tissue type and anatomical zones were compared using the Student's t test at 95% significance level.

RESULTS

The %RC of ADC, D and HS, and up to 118 (out of all 413) radiomic features was significantly different between either anatomical zones, or between tumor and benign tissue, or both.

CONCLUSIONS

DWI-derived parameters and a portion of their radiomic features require %RCs to be established specifically for anatomical zones, tumor and benign tissues. The remaining qMRI parameters and features can have a single threshold for the whole prostate.

Fast and accessible T2 mapping using off-resonance corrected DESPOT2 with application to 3D prostate

PURPOSE

Most T1 and T2 mapping take long acquisitions or needs specialized sequences not widely accessible on clinical scanners. An available solution is DESPOT1/T2 (Driven equilibrium single pulse observation of T1/T2). DESPOT1/T2 uses Spoiled gradient-echo (SPGR) and balanced Steady-State Free Precession (bSSFP) sequences, offering an accessible and reliable way for 3D accelerated T1/T2 mapping. However, bSSFP is prone to off-resonance artifacts, limiting the application of DESPOT2 in regions with high susceptibility contrasts, like the prostate. Our proposal, DESPO+, employs the full bSSFP and SPGR models with a dictionary-based method to reconstruct 3D T1/T2 maps in the prostate region without off-resonance banding.

METHODS

DESPO+ modifies the bSSFP acquisition of the original variable flip angle DESPOT2. DESPO+ uses variable repetition and echo times, employing a dictionary-based method of the full bSSFP and SPGR models to reconstruct T1, T2, and Proton Density (PD) simultaneously. The proposed DESPO+ method underwent testing through simulations, T1/T2 phantoms, and on fourteen healthy subjects.

RESULTS

The results reveal a significant reduction in T2 map banding artifacts compared to the original DESPOT2 method. DESPO+ approach reduced T2 errors by up to seven times compared to DESPOT2 in simulations and phantom experiments. We also synthesized in-vivo T1-weighted/T2-weighted images from the acquired maps using a spin-echo model to verify the map's quality when lacking a reference. For in-vivo imaging, the synthesized images closely resemble those from the clinical MRI protocol, reducing scan time by around 50% compared to traditional spin-echo T1-weighted/T2-weighted acquisitions.

CONCLUSION

DESPO+ provides an off-resonance insensitive and clinically available solution, enabling high-resolution 3D T1/T2 mapping and synthesized T1-weighted/T2-weighted images for the entire prostate, all achieved within a short scan time of 3.6 min, similar to DESPOT1/T2.

Quantitative MRI: Defining repeatability, reproducibility and accuracy for prostate cancer imaging biomarker development

INTRODUCTION

Quantitative MRI (qMRI) parameters have been increasingly used to develop predictive models to accurately monitor treatment response in prostate cancer after radiotherapy. To reliably detect changes in signal due to treatment response, predictive models require qMRI parameters with high repeatability and reproducibility. The purpose of this study was to measure qMRI parameter uncertainties in both commercial and in-house developed phantoms to guide the development of robust predictive models for monitoring treatment response.

MATERIALS AND METHODS

ADC, T1, and R2* values were acquired across three 3 T scanners with a prostate-specific qMRI protocol using the NIST/ISMRM system phantom, RSNA/NIST diffusion phantom, and an in-house phantom. A B1 field map was acquired to correct for flip angle inhomogeneity in T1 maps. All sequences were repeated in each scan to assess within-session repeatability. Weekly scans were acquired on one scanner for three months with the in-house phantom. Between-session repeatability was measured with test-retest scans 6-months apart on all scanners with all phantoms. Accuracy, defined as percentage deviation from reference value for ADC and T1, was evaluated using the system and diffusion phantoms. Repeatability and reproducibility coefficients of variation (%CV) were calculated for all qMRI parameters on all phantoms.

RESULTS

Overall, repeatability CV of ADC was <2.40%, reproducibility CV was <3.98%, and accuracy ranged between -8.0% to 2.7% across all scanners. Applying B1 correction on T1 measurements significantly improved the repeatability and reproducibility (p<0.05) but increased error in accuracy (p<0.001). Repeatability and reproducibility of R2* was <4.5% and <7.3% respectively in the system phantom across all scanners.

CONCLUSION

Repeatability, reproducibility, and accuracy in qMRI parameters from a prostate-specific protocol was estimated using both commercial and in-house phantoms. Results from this work will be used to identify robust qMRI parameters for use in the development of predictive models to longitudinally monitor treatment response for prostate cancer in current and future clinical trials.