Microstructure of Calcium Stearate Matrix Pellets: A Function of the Drying Process

The Potential Migrated Mechanism of Water-Soluble Components in Pellets Prepared by Wet Extrusion/Spheronization: Effect of Drying Rate

INTRODUCTION

At present, there are numerous researches on the migration of components in tablets and granules, however, the investigation in the pharmaceutical literatures concerning the effect of drying rate on the migration of water-soluble components of pellets is limited. Temperature and Relative Humidity (RH) are crucial parameters during the drying process, which is an essential step in the preparation of pellets via wet extrusion/spheronization. To quantify these variables, the water loss percentage of pellets per minute is defined as the drying rate.

AIM

The study aimed to investigate the influence of drying rate on the migration of water-soluble components in wet pellets and the potential migrated mechanism.

METHODS

The pellets containing tartrazine as a water-soluble model drug and microcrystalline cellulose as a matrix former were prepared by extrusion/spheronization and dried at four different drying temperatures and relative humidity. Afterwards, the extent of migrated tartrazine was assessed regarding appearance, in-vitro dissolution test, Differential Scanning Calorimetry, X-Ray Powder Diffraction, Attenuated total reflectance Fourier transform infrared spectroscopy and Confocal Raman Mapping.

RESULTS

Results demonstrated that red spots of tartrazine appeared on the surface of pellets and more than 40% tartrazine were burst released within 5 minutes when pellets were dried at 60°C/RH 10%. When pellets were dried at 40°C/RH 80%, none of these aforementioned phenomena were observed.

CONCLUSION

In conclusion, the faster the drying rate was, the more tartrazine migrated to the exterior of pellets. Adjusting drying temperature and relative humidity appropriately could inhibit the migration of water-soluble components within wet extrusion/spheronization pellets.

Approaches to developing fast release pellets via wet extrusion-spheronization

Microcrystalline cellulose (MCC) is widely regarded as the excellent choice to manufacture pellets via wet extrusion-spheronisation (ES) process due to its excellent water uptake capability, water holding capacity, desirable rheological properties, cohesiveness and plasticity etc. Nevertheless, in spite of all these advantages, limitations associated with the application of MCC also have been reported. The most prevailing limitation is prolonged or incomplete drug release profile due to the lack of disintegration as pellet contracts significantly during the drying process, especially when in combination with poorly soluble drug at a high level. This characteristic limits the application of MCC in immediate release formulations. Over the years, many approaches have been tried to overcome this disadvantage, such as modifying MCC, incorporation of superdisintegrant, increasing the porosity of pellet, partial or complete substitution for MCC, enhancing the solubility of poorly soluble drug (e.g. solid dispersion, self-emulsifying drug-delivery system), etc. In this review, we will provide an updated and integrated discussion of current approaches to prepare fast release pellets via wet ES.

Pore blocking: An innovative formulation strategy for the design of alcohol resistant multi-particulate dosage forms

In this work calcium stearate (CaSt) multi-particulates loaded with codeine phosphate (COP) were developed in an attempt to provide extended release (ER) combined with alcohol dose dumping (ADD) resistance. The pellets were prepared via wet/extrusion spheronization and ER characteristics were obtained after fluid bed drying at 30°C. Pore blockers (i.e., xanthan, guar gum and TiO2) were integrated to control the uptake of ethanolic media, the CaSt swelling and consequently, the COP release. While all three pore blockers are insoluble in ethanol, xanthan dissolves, guar gum swells and TiO2 does not interact with water. The incorporation of 10 and 15% TiO2 still provided ER characteristics and yielded ADD resistance in up to 40v% ethanol. The in-vitro data were subjected to PK simulations, which revealed similar codeine plasma levels when the medication is used concomitantly with alcoholic beverages. Taken together the in-vitro and in-silico results demonstrate that the incorporation of appropriate pore blockers presents a promising strategy to provide ADD resistance of multi-particulate systems.

Impact of drying on solid state modifications and drug distribution in ibuprofen-loaded calcium stearate pellets

Drying is a common pharmaceutical process, whose potential to alter the final drug properties-even at relatively low temperatures-is often neglected. The present study addresses the impact of drying at 20 and 50 °C on wet-extruded calcium stearate (CaSt) pellets. Drying at 20 °C caused the majority of ibuprofen to accumulate at the pellet surface due to a strong convective flow from the pellet's center to the surface. In contrast, pellets dried at 50 °C still contained ibuprofen in the pellet's interior due to the higher drying rate and the associated film breakage during drying. Moreover, the higher drying temperature caused CaSt to form a second lamellar phase and ibuprofen to convert (partly) into its amorphous state. Overall, the drying process affected the solid state and the spatial ibuprofen distribution within the pellet. Knowledge of these effects can aid in tailoring advanced multipellet formulations.