Acidity of Alginate Aerogels Studied by FTIR Spectroscopy of Probe Molecules

Construction of synthetic anti-fouling consortia: fouling control effects and polysaccharide degradation mechanisms

The physical states and chemical components of bulk sludge determine the occurrence and development of membrane fouling in membrane bioreactors. Thus, regulation of sludge suspensions can provide new strategies for fouling control. In this study, we used "top-down" enrichment to construct a synthetic anti-fouling consortium (SAC) from bio-cake and evaluate its roles in preventing membrane fouling. The SAC was identified as Massilia-dominated and could almost wholly degrade the alginate solution (1,000 mg/L) within 72 h. Two-dimensional Fourier transformation infrared correlation spectroscopy (2D-FTIR-CoS) analysis demonstrated that the SAC induced the breakage of glycosidic bond in alginates. The co-cultivation of sludge with a low dosage of SAC (ranging from 0 to 1%) led to significant fouling mitigation, increased sludge floc size, and decreased unified membrane fouling index value (0.55 ± 0.06 and 0.11 ± 0.05). FTIR spectra and X-ray spectroscopy analyses demonstrated that the addition of SAC decreased the abundance of the O-acetylation of polysaccharides in extracellular polymeric substances. Secondary derivatives analysis of amide I spectra suggested a strong reduction in the α-helix/(β-sheet + random coil) ratio in the presence of SAC, which was expected to enhance cell aggregation. Additionally, the extracellular secretions of SAC could both inhibit biofilm formation and strongly disperse the existing biofilm strongly during the biofilm incubation tests. In summary, this study illustrates the feasibility and benefits of using SAC for fouling control and provides a new strategy for fouling control.

A Bio-Based Alginate Aerogel as an Ionic Liquid Support for the Efficient Synthesis of Cyclic Carbonates from CO2 and Epoxides

In this work, the ionic liquid [Aliquat][Cl] was supported into alginate and silica aerogel matrices and applied as a catalyst in the cycloaddition reaction between CO2 and a bio-based epoxide (limonene oxide). The efficiency of the alginate aerogel system is much higher than that of the silica one. The method of wet impregnation was used for the impregnation of the aerogel with [Aliquat][Cl] and a zinc complex. The procedure originated a well-defined thin solvent film on the surface of support materials. Final materials were characterised by Fourier Transform Infrared Spectroscopy, N2 Adsorption–Desorption Analysis, X-ray diffraction, atomic absorption and Field Emission Scanning Microscopy. Several catalytic tests were performed in a high-pressure apparatus at 353.2 K and 4 MPa of CO2.

Review on the Production of Polysaccharide Aerogel Particles

A detailed study of the production of polysaccharide aerogel (bio-aerogel) particles from lab to pilot scale is surveyed in this article. An introduction to various droplets techniques available in the market is given and compared with the lab scale production of droplets using pipettes and syringes. An overview of the mechanisms of gelation of polysaccharide solutions together with non-solvent induced phase separation option is then discussed in the view of making wet particles. The main steps of particle recovery and solvent exchange are briefly described in order to pass through the final drying process. Various drying processes are overviewed and the importance of supercritical drying is highlighted. In addition, we present the characterization techniques to analyse the morphology and properties of the aerogels. The case studies of bio-aerogel (agar, alginate, cellulose, chitin, κ-carrageenan, pectin and starch) particles are reviewed. Potential applications of polysaccharide aerogel particles are briefly given. Finally, the conclusions summarize the prospects of the potential scale-up methods for producing bio-aerogel particles.

Formation of polysaccharide aerogels in ethanol

High surface area and low thermal conductivity were observed for polysaccharide aerogels prepared by ethanol induced gelation.

Nanostructure of calcium alginate aerogels obtained from multistep solvent exchange route

Ca-alginate materials were studied by small-angle X-ray scattering (SAXS) at different steps of conversion from gel to aerogel in order to determine the relation between the polymer organization at the nanoscale in the gels and the final dry aerogel. In all cases, i.e. before and after the different exchanges of solvents and after the formation of the aerogel, the SAXS patterns exhibit an asymptotic behavior at low q values (in the experimental q range 7x10(-3) up to 2.10(-2) A(-1)) close to I(q) approximately q(-1), indicative of randomly oriented rod-like scattering objects. The evolution of the diameter of such rod-like objects was thus deduced from the maxima observed on Kratky plots, i.e. I(q) q2 vs q. The results are in perfect agreement qualitatively (rod-like anisometry type of the scattering objects) and quantitatively (diameter of the rods) with direct SEM observations of the morphology of aerogels and with the results of N2 adsorption on the aerogel. This is evidence that in the chosen experimental processing conditions, the morphology of the aerogel depends on the morphology of pre-existing objects within the gel, i.e. that the structure of the aerogel provides a correct image of the structure of the parent gel.