High efficiency violet to blue light emission in porous SiC produced by anodic method

Voltage-Controlled Anodic Oxidation of Porous Fluorescent SiC for Effective Surface Passivation

This study investigated the fabrication of porous fluorescent SiC using a constant voltage-controlled anodic oxidation process. The application of a high, constant voltage resulted in a spatial distinction between the porous structures formed inside the fluorescent SiC substrates, due to the different etching rates at the terrace and the large step bunches. Large, dendritic porous structures were formed as the etching process continued and the porous layer thickened. Under the conditions of low hydrofluoric acid (HF) concentration, the uniformity of the dendritic porous structures through the entire porous layer was considerably improved compared with the conditions of high HF concentration. The resulting large uniform structure offered a sizable surface area, and promoted the penetration of atomic layer-deposited (ALD) Al₂O₃ films (ALD–Al₂O₃). The emission intensity in the porous fluorescent SiC was confirmed via photoluminescence (PL) measurements to be significantly improved by a factor of 128 after ALD passivation. With surface passivation, there was a clear blueshift in the emission wavelength, owing to the effective suppression of the non-radiative recombination rate in the porous structures. Furthermore, the spatial uniformity of emitted light was examined via PL mapping using three different excitation lasers, which resulted in the observation of uniform and distinctive emissions in the fluorescent SiC bulk and porous areas.

Temperature-dependent photoluminescence properties of porous fluorescent SiC

A comprehensive study of surface passivation effect on porous fluorescent silicon carbide (SiC) was carried out to elucidate the luminescence properties by temperature dependent photoluminescence (PL) measurement. The porous structures were prepared using an anodic oxidation etching method and passivated by atomic layer deposited (ALD) Al₂O₃ films. An impressive enhancement of PL intensity was observed in porous SiC with ALD Al₂O₃, especially at low temperatures. At temperatures below 150 K, two prominent PL emission peaks located at 517 nm and 650 nm were observed. The broad emission peak at 517 nm was attributed to originate from the surface states in the porous structures, which was supported by X-ray photoelectron spectra characterization. The emission peak at 650 nm is due to donor-acceptor-pairs (DAP) recombination via nitrogen donors and boron-related double D-centers in fluorescent SiC substrates. The results of the present work suggest that the ALD Al₂O₃ films can effectively suppress the non-radiative recombination for the porous structures on fluorescent SiC. In addition, we provide the evidence based on the low-temperature time-resolved PL that the mechanism behind the PL emission in porous structures is mainly related to the transitions via surface states.

White Light Emission from Fluorescent SiC with Porous Surface

ABSTARCT

We report for the first time a NUV light to white light conversion in a N-B co-doped 6H-SiC (fluorescent SiC) layer containing a hybrid structure. The surface of fluorescent SiC sample contains porous structures fabricated by anodic oxidation method. After passivation by 20 nm thick Al₂O₃, the photoluminescence intensity from the porous layer was significant enhanced by a factor of more than 12. Using a porous layer of moderate thickness (~10 µm), high-quality white light emission was realized by combining the independent emissions of blue-green emission from the porous layer and yellow emission from the bulk fluorescent SiC layer. A high color rendering index of 81.1 has been achieved. Photoluminescence spectra in porous layers fabricated in both commercial n-type and lab grown N-B co-doped 6H-SiC show two emission peaks centered approximately at 460 nm and 530 nm. Such blue-green emission phenomenon can be attributed to neutral oxygen vacancies and interface C-related surface defects generated dring anodic oxidation process. Porous fluorescent SiC can offer a great flexibility in color rendering by changing the thickness of porous layer and bulk fluorescent layer. Such a novel approach opens a new perspective for the development of high performance and rare-earth element free white light emitting materials.

Effective optimization of surface passivation on porous silicon carbide using atomic layer deposited Al2O3

Significant enhancement of photoluminescence in ALD Al₂O₃ passivated porous 6H-SiC.

Computational simulation of the effects of oxygen on the electronic states of hydrogenated 3C-porous SiC

A computational study of the dependence of the electronic band structure and density of states on the chemical surface passivation of cubic porous silicon carbide (pSiC) was performed using ab initio density functional theory and the supercell method. The effects of the porosity and the surface chemistry composition on the energetic stability of pSiC were also investigated. The porous structures were modeled by removing atoms in the [001] direction to produce two different surface chemistries: one fully composed of silicon atoms and one composed of only carbon atoms. The changes in the electronic states of the porous structures as a function of the oxygen (O) content at the surface were studied. Specifically, the oxygen content was increased by replacing pairs of hydrogen (H) atoms on the pore surface with O atoms attached to the surface via either a double bond (X = O) or a bridge bond (X-O-X, X = Si or C). The calculations show that for the fully H-passivated surfaces, the forbidden energy band is larger for the C-rich phase than for the Si-rich phase. For the partially oxygenated Si-rich surfaces, the band gap behavior depends on the O bond type. The energy gap increases as the number of O atoms increases in the supercell if the O atoms are bridge-bonded, whereas the band gap energy does not exhibit a clear trend if O is double-bonded to the surface. In all cases, the gradual oxygenation decreases the band gap of the C-rich surface due to the presence of trap-like states.