Nanomechanical properties of zirconium anodized in a mixture of electrolytes with fluoride ions

The present work introduces nanostructured Zr as a possible choice of metallic implant biomaterial in competition with titanium and its new alloys. The paper reports on the preparation of anodized zirconium in a mixture of electrolytes with fluoride ions, 1 M (NH₄)2SO₄ + 0.15 M NH₄F + distilled water, at 20 V. The obtained nanostructures were investigated by SEM, EDX, XRD and AFM techniques. The SEM - EDX longitudinal and cross sectional analysis revealed the morphology of the formed oxide layers and their thicknesses, which were found to be 7.45 ± 0.18 μm. The mean nanopores' diameter was calculated as 15.8 ± 3.3 nm. The XRD investigations enabled the evaluation of crystallite sizes and texture coefficients for zirconium and zirconium oxide containing samples. The inhibition effect against Escherichia coli and Streptococcus Aureus bacteria was evaluated and discussed as well. The AFM studies revealed that the nano-porous Zr has similar hardness parameter as the uncoated Zr, but lower surface adhesion force that could be translated into improved properties in terms of antimicrobial effects, as confirmed by its inhibition index, which makes it a very promising material for bio-medical applications.

Effect of anodized zirconium implants on early osseointegration process in adult rats: a histological and histomorphometric study

Since surface plays a key role in bioactivity, the response of the host to the biomaterial will determine the success or failure of the prosthesis. The purpose of this study is to make an exhaustive analysis of the histological and histochemical characteristics of new bone tissue around Zr implants anodized at 60 V (Zr60) supported by histomorphometric methods in a rat model. Fibrous tissue was observed around the control implants (Zr0) and osteoblasts were identified on the trabeculae close to the implantation site that showed typical cytological characteristics of active secretory cells, regardless of the surface condition. The histomorphometrical analysis revealed a significant increase in cancellous bone volume, trabecular thickness and in trabecular number together with a decrease in trabecular separation facing Zr60. TRAP staining showed that there was a relative increase in the number of osteoclasts for Zr60. In addition, a larger number of osteoclast with a greater number of nuclei were detected in the tibiae for Zr60. This research demonstrated that the new bone microarchitecture in contact with Zr60 is able to improve the early stages of the osseointegration process and consequently the primary stability of implants which is a crucial factor to reduce recovery time for patients.

Effect of Negative Current on the Microstructure of Oxide Coatings Prepared by Hybrid Pulse Anodization

The oxide coatings were prepared on 6061 Al alloy at different negative current densities in oxalic acid using the hybrid pulse anodization (HPA) method at room temperature. The variation curves of positive and negative voltages with anodization time were recorded. The nanopore diameters and distribution regularities in HPA coatings were analyzed with the Image-Pro Plus software based on field-emission scanning electron microscope (FE-SEM) images. The results showed that the negative current could reduce the growth rate of HPA coatings, and thus led to a small thickness of the coatings within the same anodization time. Besides, appropriate negative current densities resulted in the better distribution uniformity of nanopores, but the excessive negative current densities tended to cause inferior nanopore arrangement. These were attributed to the existence of the negative current, causing H+ and O2− to move in opposite directions, so that a large number of H+ concentrated on the surface of the HPA coatings, resulting in the accelerated dissolution of the coatings.

Biomimetic approaches in bone tissue engineering: Integrating biological and physicomechanical strategies

The development of responsive biomaterials capable of demonstrating modulated function in response to dynamic physiological and mechanical changes in vivo remains an important challenge in bone tissue engineering. To achieve long-term repair and good clinical outcomes, biologically responsive approaches that focus on repair and reconstitution of tissue structure and function through drug release, receptor recognition, environmental responsiveness and tuned biodegradability are required. Traditional orthopedic materials lack biomimicry, and mismatches in tissue morphology, or chemical and mechanical properties ultimately accelerate device failure. Multiple stimuli have been proposed as principal contributors or mediators of cell activity and bone tissue formation, including physical (substrate topography, stiffness, shear stress and electrical forces) and biochemical factors (growth factors, genes or proteins). However, optimal solutions to bone regeneration remain elusive. This review will focus on biological and physicomechanical considerations currently being explored in bone tissue engineering.