Mandibular fossa morphology during therapy with a fixed functional orthodontic appliance : A magnetic resonance imaging study

Three-dimensional spatial analysis of temporomandibular joint in adolescent Class II division 1 malocclusion patients: comparison of Twin-Block and clear functional aligner

BACKGROUND

Our study aimed to use three-dimensional (3D) spatial morphological measurement methods to compare the influence of Twin-Block and clear functional aligners on the temporomandibular joint (TMJ) of adolescent Class II division 1 malocclusion mandibular retraction patients. We also aimed to explore the similarities and differences in the effects on the TMJ upon using Twin-Block and clear functional aligner.

METHODS

Cone-beam computed tomography (CBCT) data of 49 patients with Class II division 1 malocclusion (Twin-Block group: 24; clear functional aligner group: 25) were collected before and after functional orthodontic treatment, and a 3D model of the TMJ was reconstructed using MIMICS 21.0 software. Eighteen measurement parameters, including the anterior, superior, and posterior joint spaces, were measured and compared using the 3D model.

RESULTS

After the two groups underwent functional appliance treatment, the height, volume, and surface area of the condyle, length of the mandibular ramus and mandibular length increased; The retro-displaced condyle moved to the middle position of the articular fossa, while the rest of the condylar position did not change significantly. Remodeling of the articular fossa after treatment was not evident. The superior joint space of the clear functional aligner group increased, but there was no significant change after Twin-Block appliances treatment.

CONCLUSIONS

Both appliances promote condylar growth and sagittal and vertical development of the mandible in adolescent Class II division 1 malocclusion mandibular retraction patients. The length of the mandibular ramus showed a more significant increase following treatment with the Twin-Block appliances than with clear function aligners.

Three-Dimensional Evaluation of Condyle-Glenoid Fossa Complex Following Treatment with Herbst Appliance

The purpose of the present retrospective observational study was to compare the effects of treatment with Herbst appliance and fixed therapy with elastics on the condyle and glenoid fossa complex. Thirty patients aged between twelve and sixteen years with skeletal Class II malocclusion who met the inclusion criteria were included in the study: fifteen patients treated with Herbst appliance (Group 1), and fifteen patients treated with orthodontic camouflage using MBT prescription (MBT^TM Versatile+ Appliance System) (Group 2). For Group 2, patients had CBCT scans taken before treatment either after Herbst appliance removal or at the end of treatment. CBCT scans were evaluated for changes in condyle-glenoid fossa complex using the In Vivo Dental 5.1 software. Statistical significance was set at p ≤ 0.05. On inter-group comparison, the Herbst group showed statistically significant increases in the condylar height of 1.35 mm (p ≤ 0.001) on the right and 1.21 mm (p ≤ 0.01) on the left side, and a condylar volume of 111.03 mm³ (p ≤ 0.01) on the right and 127.80 mm³ (p ≤ 0.001) on the left side. The Herbst group showed anterior remodelling on the postero-superior aspect of glenoid fossa. Herbst appliance treatment induced growth at the condylar head and anterior remodelling of glenoid fossa, thereby improving the maxilla-mandibular relationship in growing skeletal Class II patients.

3D assessment of mandibular skeletal effects produced by the Herbst appliance

BACKGROUND

A functional appliance is commonly used to optimize the development of the facial skeleton in the treatment of Class II malocclusion. Recent three-dimensional(3D) image-based analysis offers numerous advantages in quantitative measurement and visualization in orthodontics. The aim of this study was to localize in 3D the skeletal effect produced by the Herbst appliance on the mandible using the geometric morphometric technique.

METHODS

Twenty patients treated with a Herbst appliance and subsequent fixed appliances were included. Cone-beam computed tomography (CBCT) images were taken before treatment (T1), 8 weeks after Herbst appliance removal (T2), and after subsequent fixed appliance treatment (T3). Spatially dense morphometric techniques were used to establish the corresponding points of the mandible. The mandibular morphological changes from T1-T2, T2-T3, and T1-T3 were calculated for each patient by superimposing two mandibular models at two time points with robust Procrustes superimposition. These changes were then compared to the morphological changes estimated from normative mandibular growth curves over the same period. The proportion of cases exceeding the growth expression for controls was compared to a normal population using a one tailed binomial test.

RESULTS

Approximately 1.5-2 mm greater condylar changes and 0.5 mm greater changes in the chin occurred from Tl to T2. This effect lasted until the completion of treatment (T1-T3), but there was no obvious skeletal effect during the orthodontic phase (T2-T3). Approximately 40-50% of the patient sample exceeded condylar growth by > 1.5 mm compared to untreated controls (p < .05). However, changes at the chin were not statistically significant.

CONCLUSIONS

The principal skeletal effect of Herbst appliance treatment was additional increase in condylar length for about half of the sample. This inconsistency may relate to the degree of mandibular growth suppression associated with a specific malocclusion.

Are morphologic and topographic alterations of the mandibular fossa after fixed functional treatment detectable on tomograms? Visual classification and morphometric analysis

AIM

The goal was to evaluate if changes in morphology and topography of the mandibular fossa after Functional Mandibular Advancer (FMA) treatment are detectable on tomograms. Furthermore, the suitability of digital tomograms (DT) over magnetic resonance imaging (MRI) for this particular question was investigated.

MATERIALS AND METHODS

In all, 25 patients (14 female, 11 male) with a skeletal class II malocclusion received treatment with a FMA. DTs were available prior to (T1) and after (T2) FMA treatment. A total of 50 temporomandibular joints were investigated. The mandibular fossae were evaluated metrically and visually regarding treatment-induced alterations. A p < 0.05 was set as the level for statistical significance for all tests. Results were compared to the results of a recent MRI study.

RESULTS

Visual inspection of all 50 joints in the DT at T1 and T2 revealed no alterations of the fossa shape in the sagittal plane; 24 patients showed identical morphology of right and left joints. The metrical analysis revealed no significant changes regarding width, depth and ratio thereof between T1 and T2. There also were no bilateral differences. Another 18 different distance measurements between porion, mandibular fossa, articular eminence and pterygoid fossa showed no significant changes. There was no detectable proof of a fossa shift.

CONCLUSIONS

No changes in the sagittal plane, mandibular fossa, the articular tubercle, or a possible fossa shift were found in the DT of class II patients after FMA treatment. DT and MRI measurements and the visual inspection revealed identical findings; thus, DT appears to be a valuable research tool for sagittal analysis of mandibular fossa changes.