Selective peracetic acid determination in the presence of hydrogen peroxide using a label free enzymatic method based on catalase

Formation of Halogenated Byproducts upon Water Treatment with Peracetic Acid

Peracetic acid has quickly gained ground in water treatment over the last decade. Specifically, its disinfection efficacy toward a wide spectrum of microorganisms in wastewater is accompanied by the simplicity of its handling and use. Moreover, peracetic acid represents a promising option to achieve disinfection while reducing the concentration of typical chlorination byproducts in the final effluent. However, its chemical behavior is still amply debated. In this study, the reactivity of peracetic acid in the presence of halides, namely, chloride and bromide, was investigated in both synthetic waters and in a real contaminated water. While previous studies focused on the ability of this disinfectant to form halogenated byproducts in the presence of dissolved organic matter and halides, this work indicates that peracetic acid also contributes itself as a primary source in the formation of these potentially carcinogenic compounds. Specifically, this study suggests that 1.5 mM peracetic acid may form around 1-10 μg/L of bromoform when bromide is present. Bromoform formation reaches a maximum at near neutral pH, which is highly relevant for wastewater management.

Kinetic model of water disinfection using peracetic acid including synergistic effects

The disinfection efficiencies of a commercial mixture of peracetic acid against Escherichia coli were studied in laboratory scale experiments. The joint and separate action of two disinfectant agents, hydrogen peroxide and peracetic acid, were evaluated in order to observe synergistic effects. A kinetic model for each component of the mixture and for the commercial mixture was proposed. Through simple mathematical equations, the model describes different stages of attack by disinfectants during the inactivation process. Based on the experiments and the kinetic parameters obtained, it could be established that the efficiency of hydrogen peroxide was much lower than that of peracetic acid alone. However, the contribution of hydrogen peroxide was very important in the commercial mixture. It should be noted that this improvement occurred only after peracetic acid had initiated the attack on the cell. This synergistic effect was successfully explained by the proposed scheme and was verified by experimental results. Besides providing a clearer mechanistic understanding of water disinfection, such models may improve our ability to design reactors.

Improvement of Biodegradable Biocide’s Activity of Peroxyacetic Acid Basis Using Surfactants: Characterization and Stability

This paper deals with the study of the kinetics decomposition reaction of the peroxyacetic acid under influence of surfactant additives. The peroxyacetic acid shows a decomposition rate of 1.70×10−3 h−1and its activation energy is 66 kJ mol−1. The influence of temperature on the reaction of spontaneous decomposition of peroxyacetic acid was studied at two seasonal periods. Peroxyacetic acid standard and four prototypes of biocide samples with known concentration of peroxyacetic acid and hydrogen peroxide were studied. Finally, a factorial analysis ANOVA was carried out to establish significant differences (p<0.003) between the four biocide samples over time with respect to peroxyacetic acid and hydrogen peroxide concentration. From the study carried out, it can be concluded that the biocide with surfactant substances in its composition offers the best stability and its difference versus the other biocides may guarantee a better behaviour.

A high-throughput microtiter plate based method for the determination of peracetic acid and hydrogen peroxide

Peracetic acid is gaining usage in numerous industries who have found a myriad of uses for its antimicrobial activity. However, rapid high throughput quantitation methods for peracetic acid and hydrogen peroxide are lacking. Herein, we describe the development of a high-throughput microtiter plate based assay based upon the well known and trusted titration chemical reactions. The adaptation of these titration chemistries to rapid plate based absorbance methods for the sequential determination of hydrogen peroxide specifically and the total amount of peroxides present in solution are described. The results of these methods were compared to those of a standard titration and found to be in good agreement. Additionally, the utility of the developed method is demonstrated through the generation of degradation curves of both peracetic acid and hydrogen peroxide in a mixed solution.