Enhanced thermal stability of poly(methyl methacrylate) composites with fullerenes

Carbon nanotube-embedded hollow carbon nanofibers as efficient hosts for advanced lithium-sulfur batteries

Lithium-sulfur (Li-S) batteries have attracted great research attention because of their high energy density and low cost. However, shuttling effects of polysulfides and insulation from elemental sulfur hinder their practical application. Herein, we report hollow carbon nanofibers filled with carbon nanotubes (denoted as HCNF/CNT) as host materials for sulfur to mitigate the shuttling behavior and improve the kinetics of insulative sulfur. The as-prepared HCNF/CNT with nano-conductive domains in the hollow carbon nanofibers enables high loading and efficient utilization of sulfur. Owing to their unique structural superiority, the sulfur-encapsulated HCNF/CNT cathode materials for Li-S batteries deliver excellent electrochemical performance, including high specific capacity of 1156 mA h g^-1 at 0.2 C, good rate performance and cycling stability with a capacity retention of 77.2% after 200 cycles at 2 C. Such a unique structure can provide inspiration for the rational structural design of carbon materials as hosts for high performance Li-S batteries.

Surface modification of PMMA polymer and its composites with PC61BM fullerene derivative using an atmospheric pressure microwave argon plasma sheet

This paper presents the results of experimental investigations of the plasma surface modification of a poly(methyl methacrylate) (PMMA) polymer and PMMA composites with a [6,6]-phenyl-C61-butyric acid methyl ester fullerene derivative (PC₆₁BM). An atmospheric pressure microwave (2.45 GHz) argon plasma sheet was used. The experimental parameters were: an argon (Ar) flow rate (up to 20 NL/min), microwave power (up to 530 W), number of plasma scans (up to 3) and, the kind of treated material. In order to assess the plasma effect, the possible changes in the wettability, roughness, chemical composition, and mechanical properties of the plasma-treated samples’ surfaces were evaluated by water contact angle goniometry (WCA), atomic force microscopy (AFM), attenuated total reflectance Fourier transform infrared spectroscopy (ATR-FTIR) and X-ray photoelectron spectroscopy (XPS). The best result concerning the water contact angle reduction was from 83° to 29.7° for the PMMA material. The ageing studies of the PMMA plasma-modified surface showed long term (100 h) improved wettability. As a result of plasma treating, changes in the samples surface roughness parameters were observed, however their dependence on the number of plasma scans is irregular. The ATR-FTIR spectra of the PMMA plasma-treated surfaces showed only slight changes in comparison with the spectra of an untreated sample. The more significant differences were demonstrated by XPS measurements indicating the surface chemical composition changes after plasma treatment and revealing the oxygen to carbon ratio increase from 0.1 to 0.4.

Mechanical and thermal properties of PMMA resin composites for interim fixed prostheses reinforced with calcium β-pyrophosphate

Interim restorations are essential in fixed prosthodontics as they provide temporary protection of teeth before the insertion of the permanent restoration. Poly(methyl methacrylate) (PMMA) is widely used in the fabrication of interim-fixed restorations as it is a biocompatible material with a lot of convenient properties. However, it exhibits low impact and tensile strength and therefore it is necessary to be reinforced. Calcium β-pyrophosphate (β-CPP) is considered a promising reinforcing material for dental applications, especially for enamel regeneration due to its stability at low pH and its low wear rate. The aim of this study was to manufacture PMMA/β-CPP composites suitable for fixed-interim restorations and to study their mechanical and thermal properties. In order to enhance β-CPP dispersion into PMMA matrix, ball-milling was performed for 1 or 6 h. Three-point bending test was performed to study flexural strength, Dynamic Mechanical Analysis (DMA) to reveal the elastic and viscous moduli along with T_g, Fourier Transform Infrared Spectroscopy (FTIR) and X-Ray Diffraction Analysis (XRD) to investigate the structure of the materials and SEM for the morphological evaluation of both composite powders and polymerized specimens. Thermogravimetric Analysis (TGA) and Differential Scanning Calorimetry (DSC) experiments were performed to study their thermal properties. A statistically significant increase in flexural strength was found in the 0.5, 0.75 and 1% composite groups after 6 h ball-milling, relative to the control, with the 6 h ball milling mixed specimens, presenting the highest flexural strength values. The brittle fracture type was common to all groups. An obvious improvement of the mechanical properties and a slight improvement in the thermal stability of the composite materials values were also observed as β-CPP content was increased, while T_g values were statistically not-affected.