Porcine spine finite element model: a complementary tool to experimental scoliosis fusionless instrumentation

Finite element assessment of a disc-replacement implant for treating scoliotic deformity

BACKGROUND

Bracing and spinal fusion surgery have long been the primary methods for idiopathic scoliosis correction; however, there exist multiple limitations with both techniques. Growth modulation techniques have recently been attempted, but are typically performed across multiple vertebral elements. The aim of this study was to quantify the corrective abilities of a dual-angled, wedge shaped, rigid disc implant designed to correct spinal deformity.

METHODS

The 3D spinal geometry of four patients was reconstructed using calibrated radiographs, from which personal finite element models were created. Coronal and sagittal Cobb angles and axial stress distribution were calculated pre- and post- simulation of device implantation at the apical vertebral element.

FINDINGS

Insertion of a rigid wedged implant resulted in up to 90.1% coronal correction with kyphotic normalization, and reduced axial stress differential within adjacent vertebrae by up to 83.3%. This correction in axial stress differential was seen to propagate to subjacent vertebrae in both rostral and caudal directions. Insertion of two implants yielded greater correction with respect to all three measures.

INTERPRETATION

Local Cobb angle correction, increased kyphotic angle, and a decrease in axial stress differential with adjacent and subjacent vertebral levels demonstrate a potential for deformity correction from within the disc space. The decrease in axial stress differential demonstrates a capacity for growth modulation and reversal of the Heuter-Volkmann principle. Based on qualitative views of spinal shape following device implantation, the wedged implant proved more efficacious in correcting single thoracic curves than double major curves.

Assessment of trunk muscle activation and intervertebral load in adolescent idiopathic scoliosis by musculoskeletal modelling approach

Adolescent idiopathic scoliosis (AIS) is a three-dimensional deformity of the spine, the aetiology and pathogenesis of which are poorly understood. Unfortunately, biomechanical data describing trunk muscle activation and intervertebral load, which can contribute to understanding the pathomechanics of the AIS spine, cannot be measured in vivo due to the invasiveness of the procedures. The present study provides the biomechanical characterization of the spinal loads in scoliotic subjects by exploiting musculoskeletal modelling approach, allowing for calculating biomechanical measures in an assigned posture. A spine model with articulated ribcage previously developed in AnyBody software was applied. The predicted outcomes were evaluated in the upright posture, depending on scoliosis severity and curve type, in a population of 132 scoliotic subjects with mild, moderate, and severe scoliosis. Radiographic-based three dimensional reconstruction of vertebral orientations and scaling of body segments and trunk muscle cross-section area guaranteed geometrical subject-specificity. Validation analysis supporting the application of the model was performed. Trunk muscles were found more activated in the convex side of the scoliotic curve, in agreement with reference in vivo measurements, with progressive increase with scoliosis severity. The intervertebral lateral shear was found positively correlated with the severity of the scoliosis, demonstrating that the transferred load is not a priori orthogonal to vertebral endplate in the frontal plane, and thus questioning the assumption of the 'follower load' approach in case of experimental or computational study on the scoliotic spine. The study opens the way for the subject-specific characterization of scoliosis in assigned loading and motion conditions.

Induced pressures on the epiphyseal growth plate with non segmental anterior spine tethering

STUDY DESIGN

Experimental biomechanical study of pressures exerted on the epiphyseal growth plates (GP) in tethered porcine cadaveric spines.

OBJECTIVES

To experimentally measure the pressure exerted on the vertebral end plates of a tethered porcine spine model. Flexible spine tethering is a novel fusionless surgical technique that aims to correct scoliotic deformities based on growth modulation due to the pressure exerted on vertebral body epiphyseal GP. The applied pressure resulting from spine tethering remains not well documented.

METHODS

The ligamentous thoracic segment (T1-T14) of four 3-months old Duroc Landrace pigs (female; 22 kg, range: 18-27 kg) was positioned in lateral decubitus in a custom-made stand. Vertebra T14 was clamped but the remaining spine was free to slide horizontally. For every specimen, six configurations were tested: three or five instrumented motion segments (T5-T10 or T7-T10) with applied compression of 22, 44 or 66 N. The pressure generated on the GPs in the tethered side was measured with a thin force sensor slid either at the proximal, apex or distal levels. The data were analyzed with an ANOVA.

RESULTS

The pressure was significantly different between three and five instrumented motion segments (averages of 0.76 MPa ± 0.03 and 0.60 MPa ± 0.03, respectively; p < 0.05), but the pressure exerted on each GP along the instrumented spine was not significantly different for a given number of instrumented levels. The pressure was linearly correlated to the tether tension.

CONCLUSIONS

Non segmental anterior spine tethering induced similar pressures on every instrumented level regardless of the number of instrumented levels, with 21% lesser pressures with 5 motion segments.

LEVEL OF EVIDENCE

Level IV.

Development of a Three-Dimensional Finite Element Model of Thoracolumbar Kyphotic Deformity following Vertebral Column Decancellation

Background

Vertebral column decancellation (VCD) is a new spinal osteotomy technique to correct thoracolumbar kyphotic deformity (TLKD). Relevant biomechanical research is needed to evaluate the safety of the technique and the fixation system. We aimed to develop an accurate finite element (FE) model of the spine with TLKD following VCD and to provide a reliable model for further biomechanical analysis.

Methods

A male TLKD patient who had been treated with VCD on L2 and instrumented from T10 to L4 was a volunteer for this study. The CT scanning images of the postoperative spine were used for model development. The FE model, simulating the spine from T1 to the sacrum, includes vertebrae, intervertebral discs, spinal ligaments, pedicle screws, and rods. The model consists of 509580 nodes and 445722 hexahedrons. The ranges of motion (ROM) under different loading conditions were calculated for validation. The stresses acting on rods, screws, and vertebrae were calculated.

Results

The movement trend, peak stress, and ROM calculated by the current FE model are consistent with previous studies. The FE model in this study is able to simulate the mechanical response of the spine during different motions with different loading conditions. Under axial compression, the rod was the part bearing the peak stress. During flexion, the stress was concentrated on proximal pedicle screws. Under extension and lateral bending, an osteotomized L1 vertebra bore the greatest stress on the model. During tests, ligament disruption and unit deletion were not found, indicating an absence of fracture and fixation breakage.

Discussion

A subject-specific FE model of the spine following VCD is developed and validated. It can provide a reliable and accurate digital platform for biomechanical analysis and surgical planning.