Determination of As(III) and As(V) in water samples by flow injection online sorption preconcentration coupled to hydride generation atomic fluorescence spectrometry

Highly sensitive analysis of cyanogenic glycosides in cold-pressed flaxseed oil by employing cigarette filter fiber-based SPE coupled with ultra-performance liquid chromatography-tandem mass spectrometry

In this study, a highly sensitive method for analysis of 4 cyanogenic glycosides (CNGs) in cold-pressed flaxseed oil was developed by using cigarette filter fiber-based SPE and ultra-performance liquid chromatography-tandem mass spectrometry (UPLC-MS/MS). The cold-pressed flaxseed oil was diluted with 5% (v/v) isopropanol/n-hexane solution and loaded to a cigarette filters fiber-based SPE column for CNG enrichment and purification. Under optimized conditions, four CNGs could be detected with limits of detection ranging from 1.3 to 4.4 pg/mL. The linear range was 0.05-50 ng/ml with a linear correlation coefficient (r) > 0.9935. CNG recovery ranged from 113% to 133%, and the relative standard deviation was between 0.8% and 20.5%. Finally, the proposed method was applied to the determination of CNGs in nine cold-pressed flaxseed oils.

Non-chromatographic Speciation of As by HG Technique-Analysis of Samples with Different Matrices

The applicability of the hydride generation (HG) sample introduction technique combined with different spectrochemical detection methods for non-chromatographic speciation of toxic As species, i.e., As(III), As(V), dimethylarsinate (DMA) and monomethylarsonate (MMA), in waters and other environmental, food and biological matrices is presented as a promising tool to speciate As by obviating chromatographic separation. Different non-chromatographic procedures along with speciation protocols reported in the literature over the past 20 year are summarized. Basic rules ensuring species selective generation of the corresponding hydrides are presented in detail. Common strategies and alternative approaches are highlighted. Aspects of proper sample preparation before analysis and the selection of adequate strategies for speciation purposes are emphasized.

Sensitive determination of As (III) and As (V) by magnetic solid phase extraction with Fe@polyethyleneimine in combination with hydride generation atomic fluorescence spectrometry

The magnetic nanomaterial Fe@polyethyleneimine (Fe@PEI) was successfully synthesized and used as an effective adsorbent material for magnetic solid phase extraction(MSPE) of As(III) and As(V) from water samples. Fe@SiO2 nanoparticles were prepared by one pot synthetic method using a borohydride reduction method, then modified with (3-chloropropyl)trimethoxysilane to obtain Fe@SiO2-Cl by chloropropylation, which was reacted with PEI to achieve Fe@polyethyleneimine (Fe@PEI). The microstructure and morphology of Fe@PEI were characterized by transmission electron microscoscopy (TEM), Fourier transform infrared spectroscopy (FT-IR), and X-ray diffraction (XRD). The experimental results showed that Fe@PEI demonstrated excellent adsorption for As(III) and As(V). Based on this fact, the determination method for these two arsenic species earned good limits of detection (LODs) of 0.002μgL(-1) and wide calibration curves in the concentration range from 0.008 to 0.2μgL(-1). The precisions of As (III) and As (V)were 1.95% and 2.55% (RSD, n=6), respectively. The proposed method was validated with real samples and the spiked recoveries were in the range of 82.7-98.3% and the accuracies were in the range of 2-13.3%. The results demonstrated that the developed MSPE method had good advantages such as simplicity, rapid separation, low cost, easy to reuse and high-quality analytical performances, which made it attractive for rapid and efficient extraction of inorganic arsenic species in the environmental water samples.

Automated method for the determination of total arsenic and selenium in natural and drinking water by HG-AAS

A multicommutated flow system was designed and evaluated for the determination of total arsenic and selenium by Hydride Generation Atomic Absorption Spectrometry (HG-AAS). It was applied to the determination of arsenic and selenium in samples of natural and drinking water. Detection limits were 0.46 and 0.08 μg l(-1) for arsenic and selenium, respectively; sampling frequency was 120 samples h(-1) for arsenic and 160 samples h(-1) for selenium. Linear ranges found were 1.54-10 μg l(-1) (R = 0.999) for arsenic and 0.27-27 μg l(-1) (R = 0.999) for selenium. Accuracy was evaluated by spiking various water samples and using a reference material. Recoveries were in the range 95-116%. Analytical precision (s ( r ) (%), n = 10) was 6% for both elements. Compared with the Standard Methods, APHA, 3114B manual method, the system consumes at least 10 times less sample per determination, and the quantities of acid and reducing agent used are significantly lower with a reduction in the generation of pollutants and waste. As an additional advantage, the system is very fast, efficient and environmentally friendly for monitoring total arsenic and selenium levels in waters.

Eggshell membrane-based solid-phase extraction combined with hydride generation atomic fluorescence spectrometry for trace arsenic(V) in environmental water samples

The eggshell membrane (ESM) contains several surface functional groups such as amines, amides and carboxylic groups with potential as SPE adsorbent for the retention of target species of interest. In this paper, the potential use of ESM, a typical biomaterial, as solid-phase extraction (SPE) adsorbent is evaluated for analysis of trace arsenic(V) in environmental water samples in combination with hydride generation atomic fluorescence spectrometry (HG-AFS). In order to obtain the satisfactory recovery of arsenic(V), various parameters including the desorption and enrichment conditions such as pH, the flow rate and the volume of sample solution, the amount of ESM and the content of sodium chloride were systematically optimized and the effects of co-existed ions were also investigated in detail. Under the optimal conditions, arsenic(V) could be easily extracted by the ESM packed cartridge and the breakthrough adsorption capacity was found to be 3.9 microg g(-1). The favorable limit of detection (LOD) for arsenic(V) was found to be 0.001 microg L(-1) with an enrichment factor of 33.3, and the relative standard deviations (R.S.Ds) was 2.1% for 0.6 microg L(-1) arsenic (n=11). The reproducibility among columns was satisfactory (R.S.D. among columns is less than 5%). The proposed method has been successfully applied to analysis of arsenic(V) in aqueous environmental samples, which suggests the ESM can be an excellent SPE adsorbent for arsenic(V) pretreatment and enrichment from real water samples.