Extraction of gallium, indium and thallium from aquatic media using amino silica gel modified by gallic acid

Removal of Thallium from Aqueous Solutions by Adsorption onto Alumina Nanoparticles

Thallium (I) was removed from aqueous solution by using gamma-alumina nanoparticles (γANPs) materials as nano adsorbents. Varied experimental conditions such as adsorbent dose, agitation time, initial concentration, pH, and temperature effects were carried out in batch conditions in view of the optimization of thallium (I) adsorption and the identification of the adsorption mechanisms in the system γANPs-Tl. The pH effect indicated a remarkable increase in the quantity of Tl(I) removed for pH values ranging from 4 to 8, an almost constant magnitude for pH values between 8 and 10, and a decrease for pH values above 10. Considering an initial Tl(I) concentration of 20 µg/L and an adsorbent dose of 1 g/L at a pH value of 8.5, the removal was achieved at 95.12 ± 0.02% efficiency. The pseudo-second-order kinetics and the Freundlich isotherm perfectly described the adsorption mechanism. The process of thallium (I) adsorption reaction, as highlighted by thermodynamic investigations, was found to be spontaneous and exothermic with coexistence of physisorption and chemisorption with a dominance of physisorption. The diffusion model predicted multi-linearity, suggesting an involvement of surface spread and intraparticle diffusion in the sorption process. Thallium removal was effective by using γANPs as nano adsorbents.

Highly efficient removal of thallium(I) by facilely fabricated amorphous titanium dioxide from water and wastewater

In this study, amorphous hydrous titanium dioxide was synthesized by a facile precipitation method at room temperature, aiming to effectively remove thallium(I) from water. The titanium dioxide prepared using ammonia as precipitant (TiO2I) is more effective for thallium(I) uptake than the one synthesized with sodium hydroxide (TiO2II). The TiO2 obtained particles are amorphous, aggregates of many nanoparticles and irregular in shape. The thallium(I) uptake increases with the rise of solution pH value. Under neutral pH conditions, the maximal thallium(I) adsorption capacities of TiO2I and TiO2II are 302.6 and 230.3 mg/g, respectively, outperforming most of the reported adsorbents. The amorphous TiO2 has high selectivity towards thallium(I) in the presence of multiple cations such as K+, Ca2+, Mg2+, Zn2+ and Ni2+. Moreover, the TiO2I is efficient in removing thallium(I) from real river water and mining wastewater. Additionally, the spent TiO2I can be regenerated using hydrochloric acid solution and reused. The Tl(I) adsorption is achieved via replacing the H+ in hydroxyl group on the surface of TiO2 and forming inner-sphere surface complexes. Owing to its high efficiency, facile synthesis and environmental friendliness, the TiO2I has the potential to be used as an alternative adsorbent to remove Tl(I) from water.

Interaction between Amorphous Zirconia Nanoparticles and Graphite: Electrochemical Applications for Gallic Acid Sensing Using Carbon Paste Electrodes in Wine

Amorphous zirconium oxide nanoparticles (ZrO₂) have been used for the first time, to modify carbon paste electrode (CPE) and used as a sensor for the electrochemical determination of gallic acid (GA). The voltammetric results of the ZrO₂ nanoparticles-modified CPE showed efficient electrochemical oxidation of gallic acid, with a significantly enhanced peak current from 261 µA ± 3 to about 451 µA ± 1. The modified surface of the electrode and the synthesised zirconia nanoparticles were characterised by scanning electrode microscopy (SEM), Energy-dispersive x-ray spectroscopy (EDXA), X-ray powdered diffraction (XRD) and Fourier-transform infrared spectroscopy (FTIR). Meanwhile, the electrochemical behaviour of GA on the surface of the modified electrode was studied using differential pulse voltammetry (DPV), showing a sensitivity of the electrode for GA determination, within a concentration range of 1 × 10⁻⁶ mol L⁻¹ to 1 × 10⁻³ mol L⁻¹ with a correlation coefficient of R² of 0.9945 and a limit of detection of 1.24 × 10⁻⁷ mol L⁻¹ (S/N = 3). The proposed ZrO₂ nanoparticles modified CPE was successfully used for the determination of GA in red and white wine, with concentrations of 0.103 mmol L⁻¹ and 0.049 mmol L⁻¹ respectively.

Removal of thallium in water/wastewater: A review

The frequent occurrence of thallium (Tl) in surface water has led to the imposition of strict environmental regulations. The need for an overview of effective and feasible technology to remove Tl from water/wastewater has therefore become urgently. This review introduced the current available methods for Tl removal, including adsorption, oxidation-reduction precipitation, solvent extraction and ion exchange processes, and summarized their advantages and disadvantages. The results showed that a single treatment technology was difficult to remove Tl to a trace level of "μg L^-1", which required combined multi-technology to enhance the removal efficiency. In addition, the potential emergency and feasible technologies for Tl removal were recommended. However, several fundamental issues, such as the comparative toxicity of Tl(I) and Tl(III), the confliction of hydrolysis constants, the interference of complexant ligands as well as the influence of redox potential, were still needed to be addressed, since they would profoundly affect the selection of adopted treatment methods and the behavior of Tl removal. Future research efforts concerning the improvement of existing Tl removal technologies should be devoted to (a) developing multi-functional chemicals and adsorbents, non-toxic extractants, easy-recovery ion exchange resin and high-efficient coupling technology for advanced treatment, (b) carrying out large-scale experiments and economic assessment for real wastewater, and (c) providing safe-disposal treatment for the exhausted adsorption materials or sludge.

Sequential determination of gallium, indium, and thallium in environmental samples after preconcentration on halloysite nanotubes using ultrasound-assisted dispersive micro solid-phase extraction

A preconcentration procedure for gallium, indium, and thallium using HNTs was developed prior to their sequential determination by HR-CS GFAAS.

Solid Phase Extraction and Preconcentration of Trace Gallium, Indium, and Thallium Using New Modified Amino Silica

Amino silica gel functionalized with 2-hydroxy-5 -(2-hydroxybenzylideneamino)benzoic acid was synthesized, characterized and used as adsorbent for the removal of Ga³⁺, In³⁺ and Tl³⁺ from aqueous solution prior to their determination by flame atomic absorption spectrometry. Experimental parameters that affect the separation process were investigated in both batch and column modes. The maximum adsorption capacities of the sorbent are 61.7 mg g^-1, 81.3 mg g^-1 and 133.0 mg g^-1 for Ga³⁺, In³⁺ and Tl³⁺, respectively. The preconcentration factor is 200 and the limits of detection of Ga³⁺, In³⁺ and Tl³⁺ are 4.10 μg L^-1, 1.55 μg L^-1 and 1.21 μg L^-1, respectively. Interference by Al³⁺ can be masked by the addition of F^-; and that of Fe³⁺ by its reduction to Fe²⁺ using 10% ascorbic acid. The method was successfully applied for the determination of these ions in water, sediments and liquid crystal display samples.

Application of Cloud Point Extraction for Cadmium in Biological Samples of Occupationally Exposed Workers: Relation Between Cadmium Exposure and Renal Lesion

Cadmium (Cd) level in blood and urine of soldering iron workers (n=49) and 41 matched healthy controls has been assessed. Cloud point extraction was employed for preconcentration of Cd. The Cd ions formed hydrophobic complex with 9,10-phenanthraquinone monoethyl thiosemicarbazone that was extracted by surfactant-rich phases in the nonionic surfactant Triton X-114. The surfactant-rich phase was diluted with 1 M HNO3 in methanol prior to its analysis by graphite furnace atomic absorption spectrometry. The parameters affecting the extraction efficiency of the proposed method, such as solution pH, amount of complexing agent, surfactant concentration, temperature, and incubation time, were optimized. Under the optimum experimental conditions, the detection limit and the enrichment factor were 0.04 μg L(-1) and 61, respectively. Relative standard deviation of 10 μg L(-1) Cd was less than 3.0%. The accuracy of the method was examined by analysis of certified reference materials. It was observed that soldering iron workers are liable to Cd overload as indicated by higher levels of Cd in blood and urine when compared with the controls. This exposure may lead to kidney damage indicated by elevation of urinary excretion of both N-acetyl-β-D-glucosaminidase and β2-microglobulin.