Preparation of magnetic carbon nanotubes for separation of pyrethroids from tea samples

Magnetic Solid-Phase Extraction Based on Magnetite-Multiwalled Carbon Nanotubes of Non-Steroidal Anti-Inflammatories from Water Followed by LC-ESI-MS/MS

An analytical method based on liquid chromatography-electrospray ionization-tandem mass spectrometry detection (LC-ESI-MS/MS) has been developed for the determination of pharmaceutical compounds in water samples. Five non-steroidal anti-inflammatory drugs (NSAIDs) namely Naproxen, Ketoprofen, Piroxicam, Diflunisal and Celecoxib were investigated. Magnetic solid phase extraction (MSPE) was used for sample pre concentration of water samples and magnetic carbon nanotubes (Fe3O4-MWCNTs) were considered as solid phase extraction sorbent. Important parameters influencing the extraction efficiency such as nature and volume of eluent, sample pH and adsorbent mass were optimized. The developed MSPE method involved 75 mg of Fe3O4-MWCNTs sorbent, 5 mL of water sample at pH = 4 and 5 mL of 10% ammonia in methanol in the elution step. Under the optimized extraction conditions, linearity, detection and quantification limits and reproducibility were evaluated. The proposed method was successfully applied to the analysis of NSAIDs in surface waters, and mean recoveries of all the NSAIDs were above 90% with relative standard deviations < 17%. The detection and quantification limits were comprised between 0.05-3.6 ng.mL-1 and 0.2-11.9 ng.mL-1, respectively.

Magnetic Composite Based on Carbon Nanotubes and Deep Eutectic Solvents: Preparation and Its Application for the Determination of Pyrethroids in Tea Drinks

In this study, a novel composite material prepared by using deep eutectic solvent (tetrabutylammonium chloride-dodecanol, DES₅) functionalized magnetic MWCNTs-ZIF-8 (MM/ZIF-8@DES₅) was employed as an adsorbent for the magnetic solid-phase extraction of six pyrethroids from tea drinks. The characterization results show that MM/ZIF-8@DES₅ possessed sufficient specific surface area and superparamagnetism, which could facilitate the rapid enrichment of pyrethroids from tea drink samples. The results of the optimization experiment indicated that DES₅, which comprised tetrabutylammonium chloride and 1-dodecanol, was selected for the next experiment and that the adsorption properties of MM/ZIF-8@DES₅ were higher than those of MM/ZIF-8 and M-MWCNTs. The validation results show that the method has a wide linear range (0.5-400 μg L^-1, R² ≥ 0.9905), low LOD (0.08-0.33 μg L^-1), and good precision (intra-day RSD ≤ 5.6%, inter-day RSD ≤ 8.6%). The method was successfully applied to the determination of pyrethroids in three tea drink samples.

Magnetic porous carbons derived from iron-based metal-organic framework loaded with glucose for effective extraction of synthetic organic dyes in drinks

The conversion of metal-organic frameworks (MOFs) to porous carbon has attracted extensive attention for developing multifunctional adsorbent materials. Herein, we demonstrated a facile method to prepare magnetic porous carbon via calcinating MIL-101(Fe) precursor loaded with glucose at 700 °C in an N₂ atmosphere. The obtained magnetic porous carbon (MPCG) contained plenty of oxygen-containing functional groups and exhibited an enlarged specific surface area (177.7 m²/g) compared with its precursor (41.2 m²/g). In addition, MPCG can be easily separated from the matrix by a magnet. Benefitting from these advantages, the magnetic porous carbon exhibited high affinity toward four synthetic organic dyes (amaranth, ponceau 4R, sunset yellow, and lemon yellow) in an aqueous solution. Moreover, the adsorbent can be applied to quantitatively detect synthetic organic dyes in drinks coupled with chromatography. A new magnetic solid-phase extraction method for dye analysis yielded reasonable linearity (r □ 0.99), low limits of detection (0.047-0.076 μg/L), and good precision within the analyte concentration range of 0.25-50 μg/L.

Use of 1-octyl-3-methylimidazole hexafluorophosphate modified magnetic hyperbranched polyamideamine as sorbent for the extraction of pyrethroid insecticides from tea infusion

Magnetic hyperbranched polyamideamine was carboxylated using succinic anhydride and modified further with 1-octyl-3-methylimidazole hexafluorophosphate successively. The morphology and chemical composition of the prepared material was characterized by transmission electron microscopy, scanning electron microscopy, Fourier transform infrared spectroscopy, Brunauer-Emmett-Teller measurement, X-ray photoelectron spectroscopy, etc. 1-Octyl-3-methylimidazole hexafluorophosphate modified magnetic hyperbranched polyamideamine was used as sorbent in the magnetic solid-phase extraction for the separation and enrichment of five pyrethroid insecticides from tea infusion. The magnetic solid-phase extraction method proposed in this article has low method detection limits (0.53-0.71 ng/mL), acceptable coefficient of determination (0.9992-0.9998), wide linear ranges (2.5-500.0 ng/mL), and good repeatability (intraday: 1.2-6.3%; interday: 1.6-5.4%). In the detection of five pyrethroid insecticides in tea infusion, relative recoveries were in the range from 87.7 to 114.7% with satisfactory relative standard deviations (0.2-7.4%). With the aid of quantum chemistry calculations, the interaction energy between the sorbent and five pyrethroid insecticides was calculated, which proved the necessity of the modification of 1-octyl-3-methylimidazole hexafluorophosphate.

Applications of surface functionalized Fe3O4 NPs-based detection methods in food safety

Food safety has always been an issue of great concern to people. The development of rapid, sensitive and specific detection technology of food pollutants is one of the hot issues in food science field. The rapid development of functionalized Fe₃O₄ nanoparticles (NPs) provides unprecedented opportunities and technical support for the innovation of food safety detection. The surface functionalized Fe₃O₄ NPs, which combine superparamagnetic with nanoscale feature, have become an excellent tool for food quality and safety detection. This review highlights the mechanism, principles, and applications of surface functionalized Fe₃O₄ NPs-based detection technique in the agrifood industry. Then the relevant characteristics, functional roles and general mechanisms of nanomaterial-based detection of various endogenous components and exogenous pollutants in foods are discussed in detail. Ultimately, this review is expected to promote the optimization of functionalized Fe₃O₄ NPs and provide direction for the diversity of signal recognition and the sustainability of detection methods.

Use of a magnetic covalent organic framework material with a large specific surface area as an effective adsorbent for the extraction and determination of six fluoroquinolone antibiotics by HPLC in milk sample

A magnetic covalent organic framework material was synthesized with a core-shell structure using a simple solvothermal method. It was prepared with Fe₃ O₄ as the magnetic core, covalent organic framework as the shell, which synthesized from 1,3,5-triformylphloroglucinol and p-phenylenediamine by Schiff base reaction. Transmission electron microscopy, Fourier transform infrared spectroscopy, powder X-ray diffraction, vibrating sample magnetometry, and nitrogen adsorption-desorption were used to characterize magnetic adsorbent. It has showed a large specific surface area (505.6 m² /g), which can provide many adsorption sites. Moreover, the saturation magnetization value was 48.4 emu/g enough to be separated by external magnet. Six kinds of fluoroquinolones (enoxacin, fleroxacin, ofloxacin, norfloxacin, pefloxacin, and lomefloxacin) were extracted by magnetic solid phase extraction with the magnetic adsorbent. High-performance liquid chromatography detects the entire adsorption and desorption process to further evaluate the optimal extraction and desorption conditions. Under the optimal chromatographic conditions, this method showed a low detection limit (0.05 to 0.20 μg/L), good linearity in the range of 0.5 to 200 μg/L, and the enrichment factor reaches 115.5-127.3. The spiked recovery of the fluoroquinolones in milk sample ranged from 90.4 to 101.2%.

Dispersive micro-solid phase extraction based on a graphene/polydopamine composite for the detection of pyrethroids in water samples

In this study, a simple, rapid, precise, and environmentally friendly microextraction named dispersive micro-solid phase extraction based on a graphene/polydopamine composite as a sorbent was investigated for the analysis of four pyrethroids (fenpropathrin, cyhalothrin, etofenprox and bifenthrin) in water samples. The graphene/polydopamine composite was successfully synthesized using a one-step method, and was characterized by scanning electron microscopy, transmission electron microscopy, energy-dispersive spectroscopy and X-ray photoelectron spectroscopy. The simplicity and rapidity of dispersive micro-solid phase extraction and the high surface area and adsorptivity of the graphene/polydopamine composite were combined in the proposed method. Several main parameters, including the amount of the sorbent, extraction time, ionic strength and desorption conditions, were independently optimized and the results were compared to find the best extraction setup for dispersive micro-solid phase extraction. Under the optimal conditions, good linearity was observed for all the target analytes, with the coefficient of determination ranging from 0.9997 to 0.9999. The extraction recoveries obtained using the proposed method ranged from 76.81% to 85.29%, and the limits of detection varied from 1.5 to 3 μg L-1. In addition, the relative standard deviation values for the intra-day precision were between 0.41% and 3.00%, while the inter-day precision showed relative standard deviation values ranging from 1.61% to 5.59%. Overall, the figures of merit of the entire procedure showed that this technique could produce satisfactory results in the detection of pyrethroids in water samples or other organic pollutants in the future.

Magnetic solid-phase extraction of pyrethroid insecticides from tea infusions using ionic liquid-modified magnetic zeolitic imidazolate framework-8 as an adsorbent

A simple, sensitive, and reliable magnetic solid-phase extraction (SPE) method coupled with GC-MS/MS for the effective analysis of four pyrethroids from tea infusions was developed. A magnetic adsorbent, named ionic liquid-modified magnetic zeolitic imidazolate framework-8 (Fe3O4/ZIF-8/IL), was prepared by immobilizing an ionic liquid (IL) on the surface of Fe3O4/ZIF-8. The textures of Fe3O4/ZIF-8/IL were confirmed by material characterization, and the results suggested that the adsorbent possessed high magnetism (59.0 emu g-1), an adequate Brunauer-Emmett-Teller (BET) surface area (104 m2 g-1), and a large pore volume (0.68 cm3 g-1). To confirm the extraction performance of the prepared Fe3O4/ZIF-8/IL, several experimental conditions affecting the extraction efficiency were investigated. Under the optimum conditions, the limits of determination (LODs) for the four pyrethroids were in the range of 0.0065-0.1017 μg L-1 (S/N = 3 : 1) with an intra-day relative standard deviation (RSD) of ≤9.70% and inter-day RSD of ≤11.95%. The linear ranges were 0.5-50 μg L-1 for bifenthrin and 0.5-500 μg L-1 for permethrin, cypermethrin, and flucythrinate, with determination coefficients higher than 0.999. Finally, the proposed technique was successfully applied for the determination of pyrethroids in real tea infusions. This work could be extended to other IL-modified metal-organic frameworks (MOFs) and to the development of different sample pretreatment techniques.

Determination of Pyrethroids in Paris polyphylla Sample by High-Performance Liquid Chromatography Using Ultrasound-Assisted Magnetic Solid-Phase Extraction

A novel ultrasound-assisted magnetic solid-phase extraction (UA-MSPE) was developed for the separation/preconcentration of trace amounts of pyrethroids (fenpropathrin, fenvalerate, deltamethrin, and bifenthrin) in Paris polyphylla sample using carbon nanotubes based on Fe₃O₄ magnetic nanoparticles (Fe₃O₄@CNT MNPs), and high-performance liquid chromatography-UV is described. High recoveries of pyrethroids were obtained at a low MNPs concentration because sonication enhances the contact chances between magnetic nanoparticles and extractable analytes and promotes the extractability of the MSPE process. After the extraction, the adsorbent can be conveniently separated from the sample solution by an external magnet, and the adsorbed analytes were eluted from magnetic Fe₃O₄@CNT. The main factors influencing the extraction efficiency including the amount of the MNPs, the extraction time, the pH of sample solution, the sonicating time, and the desorption conditions were studied and optimized. Under the optimized experimental conditions, a good linearity was observed in the range of 1-100.0 ng mL^-1 for all the analytes, with the correlation coefficients (r) ranging from 0.9962 to 0.9991. The limits of detection of the four pyrethroids are 0.53, 0.26, 0.47, and 0.67 ng mL^-1, respectively. The recoveries of the method were in the range between 85.5% and 93.2%. This method is much faster and more effective than traditional SPE methods, and it is promising for the analysis of pyrethroids residues.

The determination of pesticides in tea samples followed by magnetic multiwalled carbon nanotube-based magnetic solid-phase extraction and ultra-high performance liquid chromatography-tandem mass spectrometry

A simple and efficient method regarding ultrasound-assisted extraction combined with magnetic solid-phase extraction (UA-MSPE) by UHPLC-MS/MS was set up for the determination of three pesticides in tea leaf samples.

Simultaneous enantioselective determination of 22 chiral pesticides in fruits and vegetables using chiral liquid chromatography coupled with tandem mass spectrometry

This paper presents a novel multi-residue method for the enantioselective analysis of 22 chiral pesticides in cucumber, tomato, cabbage, grape, mulberry, apple and pear at enantiomeric levels. Pesticides were efficiently extracted by magnetic solid-phase extraction based on graphene as sorbent. Response surface methodology was used to assist the multivariable optimization. The perfect chiral separation of the enantiomers was achieved on a Chiralpak IG column within 47 min by reversed-phase liquid chromatography coupled with tandem mass spectrometry, which is a significant improvement to resolve a large group of chiral compounds under one set of conditions. The method was validated in terms of selectivity, linearity, sensitivity, trueness and precision, which all satisfy the requirement for pesticides residue analysis. The proposed method was successfully applied for monitoring the occurrence and enantiomeric composition of pesticides in different fruits and vegetables, demonstrating its applicability for the routine analysis of chiral pesticide residues in food samples.

Determination of type A trichothecenes in coix seed by magnetic solid-phase extraction based on magnetic multi-walled carbon nanotubes coupled with ultra-high performance liquid chromatography-tandem mass spectrometry

Magnetic solid-phase extraction (m-SPE) is a promising sample preparation approach due to its convenience, speed, and simplicity. For the first time, a rapid and reliable m-SPE approach using magnetic multi-walled carbon nanotubes (m-MWCNTs) as the adsorbent was proposed for purification of type A trichothecenes including T-2 toxins (T2), HT-2 toxins (HT-2), diacetoxyscirpenol (DAS), and neosolaniol (NEO) in coix seed. The m-MWCNTs were synthesized by assembling the magnetic nanoparticles (Fe3O4) with MWCNTs by sonication through an aggregation wrap mechanism, and characterized by transmission electron microscope. Several key parameters affecting the performance of the procedure were extensively investigated including extraction solutions, desorption solvents, and m-MWCNT amounts. Under the optimal sample preparation conditions followed by analysis with ultra-high performance liquid chromatography-tandem mass spectrometry (UHPLC-MS/MS), high sensitivity (limit of quantification in the range of 0.3-1.5 μg kg(-1)), good linearity (R (2) > 0.99), satisfactory recovery (73.6-90.6 %), and acceptable precision (≤2.5 %) were obtained. The analytical performance of the developed method has also been successfully evaluated in real coix seed samples. Graphical Abstract Flow chart of determination of type A trichothecenes in coix seed by magnetic solid-phase extraction coupled with ultra-high performance liquid chromatography-tandem mass spectrometry.

Magnetic iron oxide nanoparticles functionalized multi-walled carbon nanotubes for toluene, ethylbenzene and xylene removal from aqueous solution

An effectively and functionally magnetic multi-walled carbon nanotube (MWCNTs) nano-composite (APCNT-KOH) was synthesized by a one-pot and facile method. The residual Fe catalyst particles of the as-prepared MWCNTs were utilized as magnetic materials through KOH activation. The resulting APCNT-KOH exhibited very high adsorption capacities for toluene (T), ethylbenzene (E), and xylene (X) (TEX) pollutants than many other adsorbents, because of their large specific surface area and high degree of surface activity. The adsorption process was found to be pH, ionic strength, and temperature dependent, and the maximum adsorption capacity was observed at pH 6 for TEX pollutants. The adsorption isotherm data were analyzed by applying the Langmuir, Freundlich, and Dubinin-Radushkevich isothermal models. The Langmuir model showed the best fit to the experimental isotherm data with a maximum adsorption capacity(qm,toluene = 63.34 mg/g, qm, ethylbenzene = 249.44 mg/g, qm,m-xylene = 227.05 mg/g, qm,o-xylene = 138.04 mg/g, qm,p-xylene = 105.59 mg/g). Adsorption kinetics of TEX on APCNT-KOH was appropriately described by the pseudo-second-order rate model. The desorption experiments revealed the typical adsorption-desorption hysteresis, indicating that the adsorption and desorption processes of TEX undergo different pathways due to porous structure changes before and after adsorption and desorption. Collective results demonstrate that the functionalized magnetic APCNT-KOH composites are highly-effective adsorbents for TEX removal, which provides a promising and green route for MWCNTs in wastewater treatment.

Performance and characteristics of fluoride adsorption using nanomagnetite graphite–La adsorbent

Nanomagnetite graphite–La was a promising adsorbent for effective F⁻ removal with high adsorption capacity and stable reuse ability.

Application of functionalized magnetic nanoparticles in sample preparation

Functionalized magnetic nanoparticles have attracted much attention in sample preparation because of their excellent performance compared with traditional sample-preparation sorbents. In this review, we describe the application of magnetic nanoparticles functionalized with silica, octadecylsilane, carbon-based material, surfactants, and polymers as adsorbents for separation and preconcentration of analytes from a variety of matrices. Magnetic solid-phase extraction (MSPE) techniques, mainly reported in the last five years, are presented and discussed.