A nanoporous anodized alumina wire with a nanosized hydroxyapatite coating for headspace solid-phase microextraction of phenol and chlorophenols

A novel top-down strategy for in situ construction of vertically oriented hexagonal NiCr LDHs nanosheet arrays with intercalated sulfate ions on Nichrome fiber for selective solid-phase microextraction of phenolic compounds in water samples

BACKGROUND

Phenolic compounds (PCs) are a class of polar aromatic pollutants with high toxicity in environmental water. Generally the efficient sample preparation is essential for the quantification of ultra-trace target PCs in real water sample before appropriative instrumental analysis. SPME is a convenient, solvent-free and time-saving miniaturized technique and has been recognized as a green alternative to conventional extraction techniques. In SPME, however, commercial fused-silica fibers are limited to the fragility, operation temperature, extraction capacity and selectivity as well as lifetime. Therefore, the development of new SPME fibers is always needed to overcome such limitations.

RESULTS

We presented a novel top-down strategy for in situ construction of vertically oriented hexagonal sulfate intercalated NiCr layered double hydroxide nanosheet arrays (NiCr LDHs-SO4 NSAs) on the Nichrome (NiCr) substrate by hydrothermal treatment in NaOH solution containing (NH4)2S2O8. The results showed that much shorter hydrothermal time was needed for the construction of NiCr@NiCr LDHs-SO4 NSAs fiber in the presence of (NH4)2S2O8. Moreover, the unique NiCr LDHs-SO4 NSAs coating offered open access structure, and thereby more available surface area for adsorption. The resulting fiber exhibited better extraction efficiency for phenolic compounds (PCs), faster mass transfer rate, higher mechanical stability, and longer service life than original NiCr@NiCr LDHs NSs fiber and typical commercially fused-silica fibers. After optimizing conditions, the SPME-HPLC-UV method demonstrated a linear range from 0.05 μg L-1 to 200 μg L-1 with LODs of 0.015-0.156 μg L-1 (S/N = 3) and LOQs of 0.048-0.498 μg L-1 (S/N = 10), as well as good repeatability (3.06%-5.22%) and fiber-to-fiber reproducibility (4.32%-6.49%).

SIGNIFICANCE

The developed SPME-HPLC-UV method with the constructed fiber was applied to the preconcentration and detection of different types of PCs in real water samples, showing satisfactory recoveries ranging from 86.20% to 107.8% with RSDs of 3.18%-6.69%. This study provides a new strategy for in situ construction of bimetallic hydroxides and their derived nanocomposite coatings on the NiCr fiber substrate in practical SPME application.

Application of boehmite as a fiber coating for headspace solid-phase microextraction of chlorophenols from aqueous samples

In this paper, the extraction of chlorophenols from water samples was carried out using high surface area boehmite nanoparticles as a sorbent. The surfactant-free process employed to make the nano-boehmite used in this work was simple, green, and efficient. The proposed approach was based on headspace solid-phase microextraction, followed by GC-ECD for the determination of analytes. In situ derivatization of analytes was performed with acetic anhydride in a basic medium. Various effective parameters, including the amount of derivatization reagent, ionic strength, desorption temperature and time, extraction temperature, equilibrium time, and extraction time were studied. Under optimal conditions, the linear dynamic range was 0.05-5.0 μg L-1 for 2,4-dichlorophenol and 2,6-dichlorophenol and 0.003-0.1 μg L-1 for 2,4,6-trichlorophenol. A low limit of detection (0.75 × 10-3-15 × 10-3 μg L-1), and relative standard deviations for real samples (RSDs) <10% were obtained. The precision (as intra- and inter-day RSDs) was between 1.2 and 9.8%. In comparison to commercial fibers (CAR-PDMS, 85 μm), this fiber showed a greater extraction efficiency. Various water samples were subjected to extraction by the proposed method. The recoveries ranged from 90 to 110%.

N-rich hypercrosslinked porous polymers for highly efficient preconcentration and sensitive detection of chlorophenols

Three novel N-rich hypercrosslinked porous polymers (NHCP1, NHCP2, and NHCP3) were facilely developed using Friedel-Crafts alkylation. NHCP1 with a remarkably large surface area (2066 m² g^-1) showed the best adsorption performance for chlorophenol pollutants. A sensitive and simple method was developed by using NHCP1 as a sorbent for solid-phase extraction to preconcentrate several chlorophenols in honey, water, and peach beverage samples followed by determination using a high-performance liquid chromatography-ultraviolet detector. The detection wavelength was 280 nm. Under the optimized conditions, the linear ranges were 1.67-1000 ng g^-1 for honey, 0.170-100 ng mL^-1 for water, and 0.330-100 ng mL^-1 for peach beverage samples. The detection limits (S/N = 3) were 0.500-2.00 ng g^-1, 0.0500-0.100 ng mL^-1, and 0.100-0.200 ng mL^-1, respectively. Recovery values were 89.3-111% with relative standard deviations <9.4%. The proposed extraction/preconcentration and quantitative analysis method provides an affordable and effective alternative for the preconcentration and determination of low levels of chlorophenols in real samples.

Advancements in Clay Materials for Trace Level Determination and Remediation of Phenols from Wastewater: A Review

The wide spread of phenols and their toxicity in the environment pose a severe threat to the existence and sustainability of living organisms. Rapid detection of these pollutants in wastewaters has attracted the attention of researchers from various fields of environmental science and engineering. Discoveries regarding materials and method developments are deemed necessary for the effective detection and remediation of wastewater. Although various advanced materials such as organic and inorganic materials have been developed, secondary pollution due to material leaching has become a major concern. Therefore, a natural-based material is preferable. Clay is one of the potential natural-based sorbents for the detection and remediation of phenols. It has a high porosity and polarity, good mechanical strength, moisture resistance, chemical and thermal stability, and cation exchange capacity, which will benefit the detection and adsorptive removal of phenols. Several attempts have been made to improve the capabilities of natural clay as sorbent. This manuscript will discuss the potential of clays as sorbents for the remediation of phenols. The activation, modification, and application of clays have been discussed. The achievements, challenges, and concluding remarks were provided.

Facile fabrication of hydroxyl-functionalized hypercrosslinked polymer for sensitive determination of chlorophenols

Three hydroxyl-functionalized hypercrosslinked polymers (HCP-POL, HCP-HQ and HCP-PG) were synthesized by Friedel-Crafts reaction. The HCP-HQ displayed the largest surface area and highest adsorption capacity for chlorophenols (CPs). Thus, the HCP-HQ was further modified with magnetism to obtain M-HCP-HQ. An efficient magnetic solid-phase extraction method with M-HCP-HQ as adsorbent was developed for the first time to simultaneously extract four CPs from water and honey samples before analysis by high performance liquid chromatography-diode array detection. Under optimized conditions, the low detection limits (S/N = 3) were obtained to be 0.06-0.10 ng mL^-1 for water and 0.80-1.75 ng g^-1 for honey. The method recovery was 80.7%-119%, with relative standard deviations below 9.5%. The enrichment factors of the CPs were in the range of 57-220. The extraction mechanism could be attributed to the strong polar interaction, hydrogen bonding and π-π interactions between the M-HCP-HQ and CPs. The M-HCP-HQ based method can be served as a reliable and sensitive tool for detection CPs in water and honey samples.

Electrochemical deposition of lithium coating on titanium implant with enhanced early stage osseointegration

Recently, a large number of studies have reported that lithium (Li) displayed a positive effect on osteogenesis. However, only a few studies have investigated the Li-incorporated surfaces through electrochemical deposition. In this study, electrochemical deposition was conducted on a CHI600E electrochemical workstation. The characterization of electrochemical deposition (ECD) and ECD-Li surfaces were detected by field-emission scanning electron microscopy with energy-dispersive spectrometer. rBMSCs were cultured on two surfaces for subsequent adhesion, proliferation and live/dead assay. To evaluate the effects of Li-incorporated implants by electrochemical deposition on osseointegration in vivo, teeth extraction of two premolars and one first molar in bilateral mandible were performed on six male beagle dogs. After 3 months, ZDI and ZDI-Li implants were inserted into the bilateral mandible of each beagle dog. Micro Computed Tomography (Micro-CT) and hard tissue sectioning analysis were carried out to evaluate the osseointegration at 4- and 8-weeks post-implantation. Results showed that ECD-Li surface promoted adhesion and proliferation of BMSCs in the early stage. More importantly, through micro-CT analysis, the values of bone volume/total volume (BV/TV) (0.374 ± 0.015), bone-implant contact (BIC) (0.831 ± 0.025), and Tb.Th (0.412 ± 0.007) in ZDI-Li group was significantly higher than those of ZDI group (0.302 ± 0.009, 0.700 ± 0.023, 0.353 ± 0.001, p < .01) at 4 weeks. Similarly, ZDI-Li group manifested more bone contact with the implant surfaces at 4 weeks based on hard tissue sectioning analysis, whereas no significant difference was detected between two groups at 8 weeks. Therefore, incorporating Li into implant surface through ECD could enhance early osseointegration in vivo.

Nano-hydroxyapatite/polyaniline composite as an efficient sorbent for sensitive determination of the polycyclic aromatic hydrocarbons in air by a needle trap device

Hydroxyapatite is a readily available, inexpensive, environmentally friendly adsorbent with high adsorption capacity. In this study, a polyaniline-doped nano-hydroxyapatite (PANI@HA) adsorbent was synthesized and employed in a needle trap device for the extraction of polycyclic aromatic hydrocarbons such as naphthalene, fluoranthene, benzo[a]anthracene, phenanthrene, and benzo[a]pyrene for the first time. The synthesized adsorbent was characterized by X-ray diffraction, field emission scanning electron microscopy, and Fourier-transform infrared spectroscopy analysis. Initially, effective variables such as the carryover effect, storage time, accuracy, and precision of the method were examined in the laboratory. The desorption conditions were optimized using the response surface methodology and central composite design methods. From the standpoint of quantitative parameters, the limit of detection and limit of quantitation were determined to be between 0.001 and 0.003 and 0.021 and 0.051 ng mL-1, respectively, which indicates the high sensitivity of the proposed method. Additionally, no significant changes were detected after storage of analytes inside the needle at 4 °C after 60 days. The results of this study also provide a high correlation between the results of sampling with needles containing PANI@HA and with XAD-2 adsorbent tubes (standard NIOSH 5115 method) (R 2 = 0.98). Finally, the proposed method was successfully employed in the extraction and determination of polycyclic aromatic hydrocarbons in field (real) samples. In general, it can be concluded that a needle packed with PANI@HA is a reliable and high-performance method for sampling polycyclic aromatic hydrocarbons compared to the NIOSH method.

Monitoring of priority pollutants chlorophenols in water and milk by headspace solid-phase microextraction based on electrospun polycaprolactam nanofibers decorated with cadmium oxide-carbon nanotubes

Priority pollutants chlorophenols are broadly used chemicals that are persistent in the environment and causing serious human health hazards. The current study introduces a novel adsorbent for the extraction of chlorophenols from river water, surface water, and milk by headspace solid-phase microextraction coupled with gas chromatography. The adsorbent composite was prepared by blending polycaprolactam (nylon-6) mat and newly synthesized carbon nanotubes decorated with cadmium oxide nanoparticles followed by electrospinning technique to produce based nanofiber. The proposed nanofiber was characterized by scanning electron microscopy, Fourier transform infrared spectroscopy, and X-ray diffraction techniques. The main parameters that affect extraction efficiency, including ionic strength, extraction time, desorption time, and extraction temperature, were investigated and optimized. The linear range was 0.05-5 ng/mL; the limits of detection (signal/noise=3) were 0.02-0.04 ng/mL. The relative recoveries for real samples (river water, surface water, and milk) were in the range of 84-114%.

In-situ fabrication of zeolite imidazole framework@hydroxyapatite composite for dispersive solid-phase extraction of benzodiazepines and their determination with high-performance liquid chromatography-VWD detection

A novel zeolite imidazole framework@hydroxyapatite composite (ZIF-8@HAP) was constructed via in-situ growth and developed for efficient dispersive solid-phase extraction (DSPE) of three benzodiazepines from urine samples. The prepared composite was characterized by scanning electron microscopy, energy-dispersive spectrometer, Fourier-transform infrared spectrometry, X-ray diffractometry, zeta potential analyzer, and nitrogen adsorption-desorption experiment. Characterization results showed typical dodecahedron ZIF-8 crystals that were uniformly located on the surface of rod-like HAP. The combination of ZIF-8 and HAP made the surface area significantly enhanced from 4.68 to 205.44 m² g^-1. Compared with a commercial C₁₈ adsorbent, ZIF-8@HAP exhibited superior removal performance for interfering components from urine and offered better extraction properties for the analytes. The prepared ZIF-8@HAP was applied as an adsorbent in DSPE, and the main experimental parameters, including pH and ionic strength of solution, adsorbent amount, adsorption time, elution solvent, and volume, were investigated. Under optimal conditions, the adsorption for 250 ng mL^-1 of each analyte in 4 mL of urine was accomplished within 2 min using 60 mg of adsorbent. The method of ZIF-8@HAP-based DSPE followed by high-performance liquid chromatography gave enhancement factors of 13.3-15.3, linear ranges of 2.5-500 ng mL^-1, and limits of detection (S/N = 3) of 0.7-1.4 ng mL^-1. The relative recoveries at three spiked levels ranged from 88.7 - 102% with intra-day and inter-day precisions from 3.0 - 10.3% and 2.3 - 12.3%, respectively. These results indicated that the proposed strategy had promising applicability for convenient, rapid, and efficient determination of benzodiazepines in urine samples.Graphical abstract In-situ fabrication of ZIF-8@HAP composite for dispersive solid-phase extraction of benzodiazepines in urine samples.

Electrochemically Fabricated Solid Phase Microextraction Fibers and Their Applications in Food, Environmental and Clinical Analysis

Background:

Designing an analytical methodology for complicated matrices, such as biological and environmental samples, is difficult since the sample preparation procedure is the most demanding step affecting the whole analytical process. Nowadays, this step has become more challenging by the legislations and environmental concerns since it is a prerequisite to eliminate or minimize the use of hazardous substances in traditional procedures by replacing with green techniques suitable for the sample matrix.

Methods:

In addition to the matrix, the nature of the analyte also influence the ease of creating green analytical techniques. Recent developments in the chemical analysis provide us new methodologies introducing microextraction techniques and among them, solid phase microextraction (SPME) has emerged as a simple, fast, low cost, reliable and portable sample preparation technique that minimizes solvent consumption.

Results:

The use of home-made fibers is popular in the last two decades since the selectivity can be tuned by changing the surface characteristics through chemical and electrochemical modifications. Latter technique is preferred since the electroactive polymers can be coated onto the fiber under controlled electrochemical conditions and the film thicknesses can be adjusted by simply changing the deposition parameters. Thermal resistance and mechanical strength can be readily increased by incorporating different dopant ions into the polymeric structure and selectivity can be tuned by inserting functional groups and nanostructures. A vast number of analytes with wide range of polarities extracted by this means can be determined with a suitable chromatographic detector coupled to the system. Therefore, the main task is to improve the physicochemical properties of the fiber along with the extraction efficiency and selectivity towards the various analytes by adjusting the electrochemical preparation conditions.

Conclusion:

This review covers the fine tuning conditions practiced in electrochemical preparation of SPME fibers and in-tube systems and their applications in environmental, food and clinical analysis.

Covalent Organic Framework as Fiber Coating for Solid-Phase Microextraction of Chlorophenols Followed by Quantification with Gas Chromatography-Mass Spectrometry

Headspace solid-phase microextraction coupled with gas chromatography-mass spectrometry was adopted for the simultaneous determination of seven chlorophenols (CPs) from honey and canned-yellow-peach samples. A covalent organic framework made of 1,3,5-triformylphloroglucinol (Tp) and benzidine (BD) was used as the SPME fiber coating to preconcentrate the acetylation derivatives of the CPs. The main experimental parameters including derivatization conditions, extraction temperature and time, headspace volume, salt concentration, and desorption temperature were investigated. The fiber showed a high extraction capability for the CPs. The limits of detection (LODs) for the analytes were 0.3-0.7 μg kg^-1 for honey and 0.8-1.8 μg kg^-1 for canned-yellow-peach samples, suggesting good sensitivity for the method. The response linearity was 2.4-250 μg kg^-1 for 2-CP and 3,4-CP and 1.0-150 μg kg^-1 for the other remaining analytes in the honey samples. For the canned-yellow-peach samples, the response linearity was 6.0-300 μg kg^-1 for 2-CP and 3,4-CP and 3.0-200 μg kg^-1 for the others. The correlation coefficients were higher than 0.9919. Good repeatability (RSD < 11.9%) for the method and high recoveries (70.2-113%) of the analytes were observed under the optimal conditions. The established method was satisfactorily applied for the analysis of honey and canned-yellow-peach samples.

A chromium(III) oxide-coated steel wire prepared by arc ion plating for use in solid-phase microextraction of aromatic hydrocarbons

The authors introduce an arc ion plating method for the deposition of chromium oxide (Cr₂O₃) on a steel wire substrate, and its use as a coating for solid phase microextraction. The coating has a micro- and nano-scaled structure after annealing at 700 °C. It is found that Cr₂O₃ exhibits a good extraction capability for the aromatic hydrocarbons naphthalene, anthracene, fluorene, fluoranthene, and biphenyl. Following desorption by high temperature at 300 °C, the analytes were quantified by gas chromatography (GC). The limits of detection are in the range between 20 and 200 ng·L^-1, and calibration plots are linear within a wide range (0.2 to 400 μg·L^-1). The coating has excellent mechanical properties, with a hardness is as high as 31.7 GPa, and the adhesion strength between coating and substrate reaches 20.1 N (corresponding to the critical Hertzian contact stress of 10 GPa). This, along with the chemical and thermal stability of the Cr₂O₃ coating, endows the wire with a long operational life. It was used for at least 100 times without any obvious decline of extraction capability. Graphical abstract An arc ion plating method was introduced for the deposition of chromium oxide (Cr₂O₃) on a steel wire substrate, and its use as a coating for solid phase microextraction with high mechanical strength, stability, and long operational lifetime.

Fabrication of Metal-Organic Framework MOF-177 Coatings on Stainless Steel Fibers for Head-Space Solid-Phase Microextraction of Phenols

Direct head-space solid-phase microextraction (HS-SPME) of phenols in water is usually difficult due to its polarity and solubility in aqueous matrix. Herein we report the fabrication of metal-organic framework MOF-177 coated stainless steel fiber for the HS-SPME of phenols (2-methylolphenol, 4-methylolphenol, 2,4-dimethylolphenol, 2,4-dichlorphenol, and 3-methyl-4-chlorophenol) in environmental water samples prior to the gas chromatography-mass spectrometry detection. Several parameters affecting the extraction efficiency were optimized in the experiment, including extraction temperature and time, the pH value and salt addition. The results indicated that the coated fiber gave low detection limits (0.015-0.043 μg L^-1) and good repeatability with the RSD ranging from 2.8% to 5.5% for phenols. The recoveries are between 84.5%-98.6% with the spiked level of 10 μg L^-1 for the real water samples. The established method may afford a kind of potential enrichment material and a reference method for the analysis of methylphenols in water samples.