A nanocomposite consisting of MnO2 nanoflowers and the conducting polymer PEDOT for highly sensitive amperometric detection of paracetamol

Improved MnO2 based electrode performance arising from step by step heat treatment during electrodeposition of MnO2 for determination of paracetamol, 4-aminophenol, and 4-nitrophenol

The design of electrochemical sensors is crucial considering important factors such as efficiency, low cost, biocompatibility, and availability. Manganese oxides are readily available, low-cost, and biocompatible materials, but their low conductivity limits their efficiency as sensors. Today, morphology engineering of manganese oxide has been one of the most common research topics, because manganese oxides' electrochemical properties are highly dependent on their morphologies. In this study, a method for reducing the charge transfer resistance (Rct) of MnO2-based electrodes was established by the cyclic voltammetry technique accompanied by step-by-step heat treatment to electrodeposition MnO2 nanofilm, which remarkably improved the Rct. Next, the sensing performance of MnO2/FTO for two separate measurements was examined, one for the simultaneous measurement of paracetamol (PAR) and 4-aminophenol (4-APh), and the other for the measurement of 4-nitrophenol (4-NP). Under the optimum conditions, the linear ranges of 4-APh, PAR, and 4-NP, were 0.8 to 22.0 µM, 2.0 to 55.0 µM, and 0.1-250 µM, with limits of detection (LOD) of 0.19 µM, 0.60 µM, and 0.01 µM, respectively. It also was unaffected by a 200-fold excess of interferences. In addition, the designed sensor was successfully applied to the analysis of real samples.

Ultrasensitive Electrochemical Biosensor Based on Efficient PDA-APDMAO Antifouling Interface and Dual-Signal Ratio Strategy for Trace Detection of Alpha-Fetoprotein in Human Serum

In electrochemical analysis, developing biosensors that can resist the nonspecific adsorption of interfering biomolecules in human serum remains a huge challenge, which depends on the design of efficient antifouling materials. Herein, 3-aminopropyldimethylamine oxide (APDMAO) biomimetic zwitterions were prepared as antifouling interfaces. Among them, the unique positive and negative charges (N+-O-) of APDMAO promoted its hydrogen bonding with water molecules, forming a firm hydration barrier that endowed it with strong and stable antifouling performance. Meanwhile, its inherent amino groups could copolymerize with the biomimetic adhesive dopamine to form a thin layer of quinone intermediates, providing conditions for the subsequent binding of aptamers and signal probes. Importantly, the biomimetic APDMAO with functional groups and one-step oxidation characteristics solved the challenges of zwitterionic synthesis and modification, as well as improved biocompatibility of the sensing interface, thereby expanding the application potential of zwitterions as antifouling materials in sensing analysis. Thiol-containing alpha-fetoprotein (AFP) aptamers modified with methylene blue (MB) were coupled under controllable potential, greatly reducing the incubation time, which promoted the productization application of biosensors. In addition, the ratio sensing strategy using MB as internal standard factors and concanavalin-silver nanoparticles (ConA-Ag NPs) as signal probes was introduced to reduce background and instrument interferences, thus improving detection accuracy. On this basis, the proposed antifouling electrochemical biosensor achieved sensitive and accurate AFP detection over a wide dynamic range (10 fg/mL-10 ng/mL), with a low detection limit of 3.41 fg/mL (3σ/m). This work provides positive insights into the development of zwitterionic antifouling materials and clinical detection of liver cancer markers in human serum.

A poly(3,4-ethylenedioxythiophene)/carbon nanotube hybrid film for electrocatalytic determination of tertiary butylhydroquinone

The preparation of ideal sensing materials is of great significance for the realization of high-performance electrochemical analysis. However, in previous methods, most electrode materials are firstly synthesized and dispersed, finally dropped on the electrode surface, which led to complicated operation and poor adhesion between the materials and electrode surface. In this study, a PEDOT-CNT hybrid film has been prepared by combining carboxylated carbon nanotubes as dopants with PEDOT through scalable and easy-to-operate electrochemical deposition. The PEDOT-CNT modified electrode shows excellent performance for the determination of tertiary butylhydroquinone, with a wide linear range of 0.5-820 μM, a low detection limit of 0.12 μM, high stability and reproducibility. In addition, the mechanism of electrodeposition of CNTs and tertiary butylhydroquinone has also been discussed briefly. The PEDOT-CNT hybrid film possesses the preeminent sensing capacity in monitoring tertiary butylhydroquinone, providing research clues for the design and development of new electrode materials in the future.

Novel nano-engineered environmental sensor based on polymelamine/graphitic-carbon nitride nanohybrid material for sensitive and simultaneous monitoring of toxic heavy metals

Heavy metal ions (HMIs) pollution is always a serious issue worldwide. Therefore, monitoring HMIs in environmental water is an important and challenging step to ensure environmental health and human safety. In this study, we spotlight an effortless, single-step in-situ electrochemical polymerization deposition technique to fabricate a novel, low-cost, efficient, nano-engineered poly(melamine)/graphitic-carbon nitride nanonetwork (PM/g-C₃N₄) modified screen-printed carbon electrode (SPE) for sensitive, selective, and simultaneous electrochemical monitoring of toxic HMIs in environmental waters. g-C₃N₄ nanomaterial was prepared using melamine as a precursor via pyrolysis technique. As-prepared g-C₃N₄ and melamine monomer were electrochemically in-situ polymerized/deposited over pre-anodized SPE (ASPE) using cyclic voltammetry technique. XRD, XPS, and SEM were engaged to characterize the developed electrode. The fabricated PM/g-C₃N₄/ASPE was applied as an environmental sensor to selective and simultaneous electrochemical detection of Pb²⁺ and Cd²⁺ ions using differential pulse voltammetry technique. The developed sensor displayed excellent selectivity and sensitivity towards Pb²⁺ and Cd²⁺ with limit of detections of 0.008 µM and 0.02 µM, respectively. The fabricated PM/g-C₃N₄/ASPE sensor exhibits superior stability, repeatability, good anti-interference, and applicability for recognition of Pb²⁺ and Cd²⁺ ions in real water samples. These results proved that developed environmental sensor is low-cost, efficient, practical platform for rapid, selective, simultaneous monitoring of HMIs in the environment.

Free-standing electrochemical biosensor for carcinoembryonic antigen detection based on highly stable and flexible conducting polypyrrole nanocomposite

A flexible free-standing electrochemical biosensor to detect carcinoembryonic antigen (CEA) is described based on a conducting polypyrrole (PPy) nanocomposite film electrode. The conducting PPy composite was constructed by the sandwiched structure formed by PPy doped with pentaerythritol ethoxylate (PEE) and 2-naphthalene sulfonate (2-NS-PPy) separately via electropolymerization. Gold nanoparticles (AuNPs) were fixed on the PPy composite film by electrodeposition and then connected to CEA aptamer through self-assembly to construct a free-standing electrochemical biosensor breaking away from additional soft substrates and current collector. This PPy composite film-based electrochemical biosensor exhibits satisfying sensing performance for CEA detection, with a linear range from 10^-10 g/mL to 10^-6 g/mL and a detection limit of 0.033 ng/mL, good specificity and long-term sensing stability (96.8% of the original signal after 15 days). The biosensor also presents acceptable reproducibility with 1.7% relative standard deviation. Moreover, this electrochemical biosensor owns the deformation stability that could bear various deformations (twisting, folding, and knotting) without affecting device's sensing performance. It can even maintain 99.4% of the original signal under 25% strain deformation. Due to the superior sensing performance, high stability (mechanical deformation and long-term storage), and flexibility, this free-standing electrochemical biosensor proves huge potential in application of flexible and wearable electronics.

Conductive Metal-Organic Frameworks for Amperometric Sensing of Paracetamol

An electrochemical sensor for paracetamol is executed by using conductive MOF (NiCu-CAT), which is synthesized by 2, 3, 6, 7, 10, 11-hexahydroxytriphenylene (HHTP) ligand. The utility of this 2D NiCu-CAT is measured by the detection of paracetamol, p-stacking within the MOF layers is essential to achieve high electrical conductivity, redox activity, and catalytic activity. In particular, NiCu-CAT demonstrated detection Limit of determination near 5μM for paracetamol through a wide concentration range (5-190 μM). The NiCu-CAT/GCE exhibits excellent reproducibility, stability, and interference for paracetamol.

An impedance biosensor based on magnetic nanobead net and MnO2 nanoflowers for rapid and sensitive detection of foodborne bacteria

Screening of pathogenic bacteria in foods is an effective way to prevent foodborne diseases. In this study, an impedance biosensor was developed for rapid and sensitive detection of Salmonella typhimurium using multiple magnetic nanobead (MNB) nets in a ring channel for continuous-flow separation of target bacteria from 10 mL of sample, manganese dioxide nanoflowers (MnO2 NFs) for efficient amplification of biological signal, and an interdigitated microelectrode for sensitive measurement of impedance change. First, the MNBs modified with capture antibodies were vortically injected from outer periphery of this ring channel to form multiple ring MNB nets at specific locations with high gradient magnetic fields. Then, the bacterial sample was continuous-flow injected, resulting in specific capture of target bacteria onto the nets, and the MnO2 NFs modified with detection antibodies were injected to form MNB-bacteria-MnO2 NF complexes. After the complexes were washed with deionized water to remove excessive nanoflowers and residual ions, H2O2 with poor conductivity was injected to reduce MnO2 NFs to conductive Mn2+ at neutral medium, leading to impedance decrease. Finally, impedance change was measured using the microelectrode for quantitative determination of Salmonella. This biosensor was able to separate ~60% of Salmonella from 10 mL of bacterial sample and detect Salmonella with a linear range of 3.0 × 101 to 3.0 × 106 CFU/mL in 1.5 h with lower detection limit of 19 CFU/mL. This biosensor might be further improved with higher sensitivity using a larger volume (100 mL or more) for routine screening of foodborne bacteria without bacterial pre-culture.