Simulated and clinical aerosol spread in common periodontal aerosol-generating procedures

Aerosol dynamics in dental clinics: Effects of ventilation mode on the mitigation of airborne diseases transmission

Dental operations inherently involve a high risk of airborne cross-infection among medical staff and patients due to the exposure of respiratory secretions, which contain pathogenic microorganisms and typically spread in the form of aerosols. In order to contribute to the understanding of aerosol dynamics during dental operation and efficiently mitigate their dispersion and deposition through appropriate ventilation, 3D numerical simulations and full-scale experimental measurements were performed in this study. The indoor airflow distribution and dynamic aerosol behaviors observed under three optimized ventilation schemes (Scenario I-III) were compared with those observed under the current ventilation system. Qualitative analysis was performed together with quantitative examination using the air age, air change efficiency, contaminant removal effectiveness, and deposition ratio. It is demonstrated that the ventilation currently in use is unable to effectively discharge aerosols, resulting in most of them depositing on surfaces routinely accessed by dental workers. The pronounced air mixing effect induced by the design of Scenario I facilitates the rapid dispersion of aerosols throughout the clinic, impeding the efficient removal via the outlet. Moreover, the effective elimination of indoor aerosols is only attainable by implementing high ventilation rates in Scenario II. The Scenario III exhibits better overall performance, as evidenced by the successful discharge of approximately 69.8% of injected aerosols with limited deposition on indoor surfaces under ACH = 6h-1, and further enhanced performance is observed at higher ACHs for contaminant removal. The prevailing ventilation design in dental clinics, which primarily focuses on maintaining a desirable temperature and relative humidity, often overlooks the necessity of proper ventilation for reducing the exposure risk of occupants. This study provides solid evidence for the upgrading or reconstruction of ventilation systems in dental clinics, aiming to promote a safe and healthy treatment environment.

Visualisation of Droplet Flow Induced by Ultrasonic Dental Cleaning

INTRODUCTION

During dental treatment procedures ultrasonic scalers generate droplets containing microorganisms such as bacteria and viruses. Hence, it is necessary to study the dynamic properties of generated droplets in order to investigate the risks associated with the spread of infection. The aim of this study was to visualise the flow state of droplets and to evaluate the impact of droplets generated during the use of an ultrasonic scaler during an oral surgical procedure.

METHODS

We studied the spatial flow of liquid droplets through a combination of imaging and numeric simulation of a simulated dental treatment processes. First, we photographed the real time images of the ultrasonic scaler and evaluated the images using image-processing software Image J to visualise the flow of liquid droplets. Finally we simulated the flow process of liquid droplets by using the initial velocity of droplet splashing and the angle of the obtained information using computerised fluid dynamics technology.

RESULTS

Under different working conditions, the droplet particle splashing velocity, maximum height, and spray angle varied, but the particle trajectory was generally parabolic. The maximum droplet velocity varied between 3.56 and 8.56 m/s, and the splashing height was between 40 and 110 mm.

CONCLUSIONS

During risk assessment of an ultrasonic scaler usage, difficulties arise due to the insufficient research on droplet velocity and distribution. This study aims to address this gap by visualising the flow trajectories of droplets generated by ultrasonic scalers. The obtained data will assist in developing more effective interventions based on spatial and temporal distribution of droplets. This provides a new approach for droplet particle research and offers new strategies for public health prevention and control.

Study of aerosol dispersion and control in dental practice

OBJECTIVES

In this study, we investigated the dispersion patterns of aerosols and droplets in dental clinics and developed a suction device to evaluate its effectiveness in reducing aerosols during dental procedures.

MATERIALS AND METHODS

Firstly, the continuous images of oral aerosols and droplets were photographed with a high-speed camera, and the trajectories of these particles were recognized and processed by Image J to determine key parameters affecting particle dispersion: diffusion velocity, distance, and angle. Secondly, based on the parameter data, the flow field of aerosol particles around the oral cavity was simulated using computational fluid dynamics (CFD), and the flow field under adsorption conditions was simulated to demonstrate the aerodynamic characteristics and capture efficiencies of the single-channel and three-channel adsorption ports at different pressures. Finally, according to the simulated data, a three-channel suction device was developed, and the capture efficiency of the device was tested by the fluorescein tracer method.

RESULTS

The dispersion experimental data showed that aerosol particles' maximum diffusion velocity, distance, and angle were 6.2 m/s, 0.55 m, and 130°, respectively. The simulated aerosol flow-field distribution was consistent with the aerosol dispersion patterns. The adsorption simulation results showed that the outlet flow rate of single-channel adsorption was 184.5 L/s at - 350 Pa, and the aerosol capture efficiency could reach 79.4%. At - 350 Pa and - 150 Pa, the outlet flow rate of three-channel adsorption was 228.9 L/s, and the capture efficiency was 99.23%. The adsorption experimental data showed that the capture efficiency of three-channel suction device was 97.71%.

CONCLUSIONS

A three-channel suction device was designed by simulations and experiments, which can capture most aerosols in the dental clinic and prevent them from spreading.

CLINICAL RELEVANCE

Using three-channel suction devices during oral treatment effectively reduces the spread of oral aerosols, which is essential to prevent the spread of epidemics and ensure the health and safety of patients and dental staff.

Particle generation and dispersion from high-speed dental drilling

OBJECTIVE

To investigate the characteristics of particle generation and dispersion during dental procedure using digital inline holography (DIH) METHODS: Particles at two locations, near-field and far-field, which represent the field closer to the procedure location and within 0.5 m from the procedure location respectively, are studied using two different DIH systems. The effect of three parameters namely rotational speed, coolant flow rate, and bur angle on particle generation and dispersion are evaluated by using 10 different operating conditions. The particle characteristics at different operating conditions are estimated from the holograms using machine learning-based analysis.

RESULTS

The particle concentration decreased by at least two orders of magnitude between the near-field and far-field locations across the 10 different operating conditions, indicating significant dispersion of the particles. High rotational speed is found to produce a larger number of smaller particles, while lower rotational speeds generate larger particles. Coolant flow rate is found to have a greater impact on particle transport to the far-field location. Irregular shape dental particles account for 29% of total particles at far-field location, with the majority of these irregular shape particles having diameters ranging from 12 to 18 μm.

CONCLUSIONS

All three parameters have significant effects on particle generation and dispersion, with rotational speed having a more significant influence on particle generation at near-field and coolant flow rate playing a more important role on particle transport to the far-field.

CLINICAL RELEVANCE

This study provides valuable insights on particle characteristics during high-speed drilling. It can help dental professionals minimize exposure risks for themselves and patients by optimizing clinical operating conditions.

Reduction of aerosol dissemination in a dental area generated by high-speed and scaler ultrasonic devices employing the "Prime Protector"

The use of an external dome aerosol containment device (Prime Protector) is proposed to reduce the spread of particles within the dental office. Hence, the aim of our study was to compare the spread of bioaerosols generated by a High-speed Handpiece (HH) and an Ultrasonic Prophylaxis Device (UPD), with and without the Prime Protector dome (PP) by counting Colony Forming Units (CFU) of Lactobacillus casei Shirota, at different distances on the x and y axis. The PP was located considering the parallelism between the base of the dome and the frontal plane of the simulator, aligning the center of the mouth with the center of the dome. The PP dome measurements are 560.0mm x 255.0mm x 5mm. Petri dishes were placed at 0.5 m, 1 m and 1.5 m respectively. Aerosol generation in the laboratory environment was done three times with the following experimental groups 1) HH, 2) HH-PP, 3) UPD, 4) UPD-PP. Each dental device activation (HH and UPD) had a time frame of 2 minutes on the upper anterior teeth of the dental phantom with a liquid suspension containing Lactobacillus casei Shirota (YAKULT 0836A 0123; 1027F 0407). Air pressure and ventilation were parameterized. No separate high-volume evacuation used, nor was there any air removal attached to the dome. Results showed no significant difference between distance and axis in the CFU count. When means for devices and distances were compared between each of them all showed significant differences except for UPD and UPD-PP (p <0,004). In conclusion, external devices like Prime Protector could help decrease aerosol diffusion during high-speed handpiece activation. However, this dome does not replace the use of PPE inside dental clinics.

Engineered adult stem cells: Current clinical trials status of disease treatment

Regenerative medicine is an interdisciplinary field involving the process of replacing and regenerating cells/tissues or organs by integrating medicine, science, and engineering principles to enhance the intrinsic regenerative capacity of the host. Recently, engineered adult stem cells have gained attention for their potential use in regenerative medicine by reducing inflammation and modulating the immune system. This chapter introduces adult stem cell engineering and chimeric antigen receptor T cells (CAR T) gene therapy and summarises current engineered stem cell- and extracellular vesicles (EVs)-focused clinical trial studies that provide the basis for the proposal of a personalised medicine approach to diseases diagnosis and treatment.

Bioprinting extracellular vesicles as a "cell-free" regenerative medicine approach

Regenerative medicine involves the restoration of tissue or organ function via the regeneration of these structures. As promising regenerative medicine approaches, either extracellular vesicles (EVs) or bioprinting are emerging stars to regenerate various tissues and organs (i.e., bone and cardiac tissues). Emerging as highly attractive cell-free, off-the-shelf nanotherapeutic agents for tissue regeneration, EVs are bilayered lipid membrane particles that are secreted by all living cells and play a critical role as cell-to-cell communicators through an exchange of EV cargos of protein, genetic materials, and other biological components. 3D bioprinting, combining 3D printing and biology, is a state-of-the-art additive manufacturing technology that uses computer-aided processes to enable simultaneous patterning of 3D cells and tissue constructs in bioinks. Although developing an effective system for targeted EVs delivery remains challenging, 3D bioprinting may offer a promising means to improve EVs delivery efficiency with controlled loading and release. The potential application of 3D bioprinted EVs to regenerate tissues has attracted attention over the past few years. As such, it is timely to explore the potential and associated challenges of utilizing 3D bioprinted EVs as a novel "cell-free" alternative regenerative medicine approach. In this review, we describe the biogenesis and composition of EVs, and the challenge of isolating and characterizing small EVs - sEVs (< 200 nm). Common 3D bioprinting techniques are outlined and the issue of bioink printability is explored. After applying the following search strategy in PubMed: "bioprinted exosomes" or "3D bioprinted extracellular vesicles", eight studies utilizing bioprinted EVs were found that have been included in this scoping review. Current studies utilizing bioprinted sEVs for various in vitro and in vivo tissue regeneration applications, including angiogenesis, osteogenesis, immunomodulation, chondrogenesis and myogenesis, are discussed. Finally, we explore the current challenges and provide an outlook on possible refinements for bioprinted sEVs applications.

Emerging Technologies of Three-Dimensional Printing and Mobile Health in COVID-19 Immunity and Regenerative Dentistry

The ongoing coronavirus disease 2019 (COVID-19) pandemic highlights the importance of developing point-of-care (POC) antibody tests for monitoring the COVID-19 immune response upon viral infection or following vaccination, which requires three key aspects to achieve optimal monitoring, including three-dimensional (3D)-printed POC devices, mobile health (mHealth), and noninvasive sampling. As a critical tissue engineering concept, additive manufacturing (AM, also known as 3D printing) enables accurate control over the dimensional and architectural features of the devices. mHealth refers to the use of portable digital devices, such as smartphones, tablet computers, and fitness and medical wearables, to support health, which facilitates contact tracing, and telehealth consultations during the pandemic. Compared with invasive biosample (blood), saliva is of great importance in the spread and surveillance of COVID-19 as a noninvasive diagnostic method for virus detection and immune status monitoring. However, investigations into 3D-printed POC antibody test and mHealth using noninvasive saliva are relatively limited. Further exploration of 3D-printed antibody POC tests and mHealth applications to monitor antibody production for either disease onset or immune response following vaccination is warranted. This review briefly describes the severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) virus and immune response after infection and vaccination, then discusses current widely used binding antibody tests using blood samples and enzyme-linked immunosorbent assays on two-dimensional microplates before focusing upon emerging POC technological platforms, such as field-effect transistor biosensors, lateral flow assay, microfluidics, and AM for fabricating immunoassays, and the possibility of their combination with mHealth. This review proposes that noninvasive biofluid sampling combined with 3D POC antibody tests and mHealth technologies is a promising and novel approach for POC detection and surveillance of SARS-CoV-2 immune response. Furthermore, as key concepts in dentistry, the application of 3D printing and mHealth was also included to facilitate the appreciation of cutting edge techniques in regenerative dentistry. This review highlights the potential of 3D printing and mHealth in both COVID-19 immunity monitoring and regenerative dentistry.