Deterioration of anterior resin composite restorations in moderate to severe tooth wear patients: 3-year results

5.5-year-survival of CAD/CAM resin-based composite restorations in severe tooth wear patients

OBJECTIVES

Aim of this prospective study was to assess full mouth rehabilitation of severe tooth wear patients using minimally invasive CAD/CAM resin-based composite (RBC) restorations and direct veneers by evaluating restoration survival up to 5.5-years.

METHODS

Twenty-two patients with generalized severe tooth wear with functional and/or esthetic problems were included. Following minimally invasive preparation, CAD/CAM RBC restorations (LAVA Ultimate,3M) were adhesively luted, direct RBC veneers (Filtek Supreme XTE, 3M) were applied in the aesthetic region. Patients were recalled after 1m,1y,3y,5y and seen in between recalls by their general dentists or at the clinical study center if complaints occurred. Failures were categorized as F1 (severe deficiencies requiring replacement/extraction), F2 (localized deficiencies requiring re-cementation/repair) and F3 (small chippings requiring refurbishment/monitoring). Survival of indirect restorations was evaluated using lifetables and Kaplan-Meier-graphs, distinguishing between failure categories and tooth type (front teeth=FT, premolars=PM, molars=M). F1 + F2 and F1 + F2 + F3 failures were analyzed using Cox regression on the variables tooth type/ location, age, gender and VDO increase (p < 0.05).

RESULTS

568 indirect restorations and 200 direct veneers in 21 patients evaluated for up to 5.5-years. For indirect restorations, 96 failures were recorded (F1:6;F2:41;F3:49) and annual failure rates were 0.29%(FT), 1.56%(PM), 2.93%(M) for F1 +F2 and 0.53%(FT), 2.42%(PM), 6.11%(M) for F1 + F2 + F3. Reasons for failure were chipping fracture (48), adhesive fracture (32), complete debonding (7), caries (4), endodontic treatment (1) and reasons unknown (documentation general dentists, 4). Molar tooth type had a statistically significantly increased probability of failure compared with front teeth and premolars for F1 + F2 + F3 (p < 0.006). Direct veneer restorations showed 18 failures (F1:2;F2:9;F3:7).

SIGNIFICANCE

Minimally invasive CAD/CAM RBC restorations combined with direct RBC veneers showed an acceptable clinical mid-term survival for restorative rehabilitation of severely worn dentitions.

Long-term occlusal tooth wear at the onset of permanent dentition

OBJECTIVES

This study quantified the long-term occlusal wear in the natural posterior teeth and the associations per tooth type within the dentition.

METHODS

The sample included 70 orthodontically treated subjects (52 females and 18 males; median age, 14.3 years), followed for a 12.7-year period. They were consecutively selected with no tooth wear-related criteria. Post-treatment (T1) and follow-up dental casts (T2) were scanned and superimposed through three-dimensional methods. Occlusal wear volume of posterior teeth and tooth wear patterns were investigated through non-parametric statistics and analysis of covariance.

RESULTS

There were no significant differences between contralateral teeth. The average occlusal wear per posterior tooth was 2.3 mm3, with 65.2% of teeth showing values greater than 1 mm3. Males, mandibular teeth, and first molars exhibited slightly greater wear levels than females (median, 2.57 and 2.21 mm3, respectively; p = 0.005), maxillary teeth, and first or second premolars, respectively. In all first premolars and in the mandibular second premolars, the buccal cusps were primarily affected with no other distinct patterns. There were weak to moderate correlations between tooth types, apart from certain strong correlations detected in males.

CONCLUSIONS

Posterior tooth wear was highly prevalent after a 13-year period starting at the onset of permanent dentition. The detected patterns are in accordance with the concept of canine guidance occlusion that is transforming into group synergy through function.

CLINICAL RELEVANCE

The widespread tooth wear occurrence and the high intra- and inter-individual variability underline the need for individual patient monitoring to identify high-risk patients at early stages.

Study on the Restoration of Class II Carious Cavities by Virtual Methods: Simulation of Mechanical Behavior

The restoration of class II cavities is predominantly carried out with composite materials. Due to the high failure rate in restoring this type of cavity, composite materials with much-improved properties and new application techniques have been promoted. The study aimed to analyze the mechanical behavior of several topical composite materials (nanocomposites, nanohybrids and ormocer) using different application techniques. In a lower second molar, a class II occlusal cavity was prepared. As filling materials, we used the following combinations: Admira Fusion and Admira Fusion Flow, Grandio and Grandio Flow, Filtek Supreme XT and Filtek Supreme Flow. These were applied using a snow plow, injection molded and Bichacho techniques. Three-dimensional scanning of the molar with the prepared cavity was performed, and then scanning of each layer of added composite material was performed, obtaining three-dimensional models. The virtual molar models were analyzed with software specific to the finite element analysis method, where their physical-mechanical properties were entered and assigned to the components of the virtual molar. Simulations at high forces specific to bruxism were then carried out and analyzed, and compared. The values of displacements and strain, for all six analyzed situations, are relatively small (range from 5.25 × 10^-6-3.21 × 10^-5 for displacement, 6.22 × 10^-3-4.34 × 10^-3 for strain), which validates all three methods and the materials used. As far as the stress values are concerned, they are similar for all methods (250-300 MPa), except for the snow plow and injection-molded techniques using Grandio and Grandio Flow composites, where the maximum von Mises stress value was more than double (approximately 700 MPa). When using the combination of Grandio and Grandio Flow materials, the 1 mm thickness of the fluid composite layer was found to have a major influence on occlusal forces damping as opposed to 0.5 mm. Therefore, the Bichacho technique is indicated at the expense of the snow plow and injection-molded techniques. The composite materials used by us in this study are state-of-the-art, with clear indications for restoring cavities resulting from the treatment of carious lesions. However, their association and application technique in the case of Class II cavities is of clinical importance for resistance to masticatory forces.

Resin Composites in Posterior Teeth: Clinical Performance and Direct Restorative Techniques

Resin composites are the most versatile restorative materials used in dentistry and the first choice for restoring posterior teeth. This article reviews aspects that influence the clinical performance of composite restorations and addresses clinically relevant issues regarding different direct techniques for restoring posterior teeth that could be performed in varied clinical situations. The article discusses the results of long-term clinical trials with resin composites and the materials available in the market for posterior restorations. The importance of photoactivation is presented, including aspects concerning the improvement of the efficiency of light-curing procedures. With regard to the restorative techniques, the article addresses key elements and occlusion levels for restoring Class I and Class II cavities, in addition to restorative strategies using different shades/opacities of resin composites in incremental techniques, restorations using bulk-fill composites, and shade-matching composites.