RP-HPLC Method for Simultaneous Determination of Sofosbuvir and Ledipasvir in Tablet Dosage Form and Its Application to In Vitro Dissolution Studies

UPLC Estimate of Sofosbuvir and Ledipasvir Utilizing Greenness Tool in Conjunction With an Analytical Quality by Design

Ledipasvir in combination with sofosbuvir approved by regulatory bodies used to treat chronic hepatitis C. The present work investigates the design and development of a new, quick, green, and selective UPLC (ultra-performance liquid chromatography) approach to concurrently quantify sofosbuvir and ledipasvir. Optimization with Box-Behnken design paired the green analytical method and quality by design-based risk assessment. A mobile phase of 65%:35% ethanol by volume and phosphate buffer (15 mM; pH 3.0) was used, with a flow rate of 0.28 mL per minute, to achieve the best chromatographic separation. With linearities ranging from 20 to 100, 4.5-22.5 μg/mL, and R2 values of 0.9999 and 0.9997, respectively, the established UPLC-PDA technique proved sensitive and specific for sofosbuvir and ledipasvir. The stability-indicating test findings demonstrate the degradation under the relevant stress conditions. The most environmentally friendly results were found when the level of environmental sustainability was evaluated using four advanced metrics: GAPI, AES, AMGS, and AGREE. Based on the findings, we came to the conclusion that the UPLC technique that was developed would be effective for the concurrent analysis of sofosbuvir and ledipasvir in tablet medication.

A new fluorescence probe for sofosbuvir analysis in dosage form and spiked human plasma

A simple, rapid, and low-cost technique was developed to allow reliable analysis of the anti-hepatitis C drug sofosbuvir in bulk, tablet form, and spiked human plasma. This method depends on the ability of sofosbuvir to quench the fluorescence of the newly synthesized 2-amino-3-cyano-4,6-dimethylpyridine (reagent 3). Elemental analysis and spectral data were used to validate the structure of the synthesized reagent. The newly synthesized reagent exhibited a satisfactory level of fluorescence emission at 365 nm after excitation at 247 nm. All experimental variables that might affect the quenching process were analyzed and optimized. Linearity, range, accuracy, precision, limit of detection (LOD), and limit of quantitation (LOQ) were all validated in accordance with the International Council for Harmonization of Technical Requirements for Pharmaceuticals for Human Use (ICH) guidelines. The concentration range was shown to be linear between 0.1 and 1.5 μg/mL. The technique was effectively utilized for sofosbuvir analysis in both its tablet dosage form and spiked human plasma, with mean percentage recoveries of 100.13 ± 0.35 and 94.26 ± 1.69, respectively.

Development of stability indicating reversed phase HPLC method for determination of elobixibat in pure form and Laboratory prepared tablets: Application to dissolution study

A simple stability indicating reversed phase HPLC method has been developed for determination of elobixibat in presence of its potential impurities and degradation products. The chromatographic separation was carried on a Thermo scientific Base Deactivated Silica BDS Hypersil-C18 (150 × 4.6 mm; 5 μm) column using a mobile phase of acetonitrile and phosphate buffer (25 mM, pH 2.5) in a ratio of (70:30, volume/volume percentage). The experimental conditions were accurately investigated, and the method was validated according to International Conference on Harmonization ICH guidelines Q2 (R1). The drug was subjected to various stress conditions including acidic, basic, oxidative, and photolytic conditions. The method successfully separates the drug from the three reported impurities and different degradants. The method was also successfully applied for the determination of elobixibat in laboratory prepared tablets (5.0 mg). Analysis shows no interference from excipients and degradation products. The method was also applied for performing in vitro dissolution testing of elobixibat laboratory prepared tablets. Since elobixibat is recently introduced into the market, there are no previous stability studies and no reported analytical methods for its determination. Thus, this study presents a validated and selective method that can be effectively employed in routine quality control studies. This article is protected by copyright. All rights reserved.

Computational design for eco-friendly visible spectrophotometric platform used for the assay of the antiviral agent in pharmaceutical dosage form

Nowadays, the analytical community is focusing on developing new analytical methods that incorporate principles of green analytical chemistry to reduce adverse impacts on the environment and humans. In this study, we focused specifically on establishing a correlated connection between theoretical and experimental applications via developing green, and eco-friendly visible spectrophotometric methods. These methods were relied on charge-transfer complexation (CTC) between ledipasvir and 2,3-dichloro-5,6-dicyano-1,4-benzoquinone (DDQ), or chloranilic acid (CA) for sensitive colorimetric analysis of ledipasvir in the presence of sofosbuvir (Sofolanork plus®). The results were evaluated as modern computational chemistry using molecular modeling technology. At ambient temperature, the reactions for DDQ and CA took 15 and 10 min, respectively, to produce a purple red-colored solution with DDQ absorbing maximally at 588 nm and a purple-colored solution with CA absorbing maximally at 522 nm. Linearity was achieved for ledipasvir utilizing DDQ and CA in the concentration ranges of 8-80 µg.mL^-1 and 40-400 µg.mL^-1, respectively. The precision and accuracy of the methods mentioned were determined. Finally, the results were statistically compared to a previously published spectrophotometric technique, and no significant differences were found.

Innovative derivative/zero ratio spectrophotometric method for simultaneous determination of sofosbuvir and ledipasvir: Application to average content and uniformity of dosage units

An innovative simple, rapid and sensitive spectrophotometric method was developed for the simultaneous analysis of sofosbuvir (SOF) and ledipasvir (LED) in their combined dosage forms. Sofosbuvir with ledipasvir (SOF/LED) as a combined dosage form was tried at the pandemic COVID 19 crisis. This technique has the advantages of both zero order and first order spectrophotometry. The zero and first derivative amplitudes were measured at 274.2 nm for SOF (zero crossing point of LED in first derivative spectrum) and 314 nm for LED (zero crossing point of SOF in first derivative spectrum) over the concentration range of 2.0-50.0 μg mL^-1 with coefficients of determination (R²) > 0.9999 for both drugs and mean percentage recoveries of 100.25 ± 1.61 and 99.85 ± 0.99 for SOF and LED; respectively. This original method was validated according to ICH requirements and statistically compared to published comparison methods. This method was applied to estimate the average content and the uniformity of dosage units of SOF/LED combined dosage form according to British Pharmacopeia requirements.

An intelligent method based on feed-forward artificial neural network and least square support vector machine for the simultaneous spectrophotometric estimation of anti hepatitis C virus drugs in pharmaceutical formulation and biological fluid

This study proposed simple and reliable spectrophotometry method for simultaneous analysis of hepatitis C antiviral binary mixture containing sofosbuvir (SOF) and daclatasvir (DAC). This technique is based on the use of feed-forward artificial neural network (FF-ANN) and least square support vector machine (LS-SVM). FF-NN with Levenberg-Marquardt (LM) and Cartesian genetic programming (CGP) algorithms was trained to determine the best number of hidden layers and the number of neurons. This comparison demonstrated that the LM algorithm had the minimum mean square error (MSE) for SOF (1.59 × 10^-28) and DAC (4.71 × 10^-28). In LS-SVM model, the optimum regularization parameter (γ) and width of the function (σ) were achieved with root mean square error (RMSE) of 0.9355 and 0.2641 for SOF and DAC, respectively. The coefficient of determination (R²) value of mixtures containing SOF and DAC was 0.996 and 0.997, respectively. The percentage recovery values were in the range of 94.03-104.58 and 94.04-106.41 for SOF and DAC, respectively. Statistical test (ANOVA) was implemented to compare high-performance liquid chromatography (HPLC) and spectrophotometry, which showed no significant difference. These results indicate that the proposed method possesses great potential ability for prediction of concentration of components in pharmaceutical formulations.

Multivariate optimization and evaluation of quaternary mixture in bulk and co-formulated dosage forms by central composite design

Background

The current study describes the use of central composite design for multivariate optimization of resolution and retention time, taking into account different critical method parameters like organic phase, pH, flow rate, and wavelength for risk assessment. The chromatographic method for the assay of the most effective anti-viral regimen (EPCLUSA, DARVONI, and HARVONI) was developed. An experimental design was presented by sequential investigation of four independent parameters. The method was developed using XTERRA C18 (250 mm × 4.6 mm, 5 μm particle size) column in isocratic mode using potassium dihydrogen phosphate buffer (pH adjusted to 5) and acetonitrile (50:50 % v/v) as mobile phase at a flow rate of 1.0 ml/min and UV detection wavelength of 260 nm.

Results

The separation of four drugs with fine resolution and preferable retention times was achieved. Retention times of four drugs were found to be 2.96, 3.91, 7.15, and 11.94 min for daclatasvir, sofosbuvir, velpatasvir, and ledipasvir, respectively. The percentage accuracy of labelled claim was in the range of 99–102%, and the pooled %RSD for repeatability, precision, and accuracy was less than 2%.

Conclusion

The suggested method was applied for quantification and identification of studied drugs in tablets; the results agreed with the label claim and were validated according to the ICH guidelines. The optimized method can be used for pharmacokinetic and quality control studies.

Liver Targeting of Daclatasvir via Tailoring Sterically Stabilized Bilosomes: Fabrication, Comparative In Vitro/In Vivo Appraisal and Biodistribution Studies

INTRODUCTION

Hepatitis C virus (HCV) is a significant public health concern that threatens millions of individuals worldwide. Daclatasvir (DAC) is a promising direct-acting antiviral approved for treating HCV infection around the world. The goal of this study was to encapsulate DAC into novel polyethylene glycol (PEG) decorated bilosomes (PEG-BILS) to achieve enhanced drug delivery to the liver.

METHODS

DAC-loaded BILS were primed by a thin film hydrating technique. The study of the impact of various formulation variables on the properties of BILS and selection of the optimal formulation was generated using Design-Expert® software. The optimum preparation was then pegylated via the incorporation of PEG-6-stearate (5% w/w, with respect to the lipid phase).

RESULTS

The optimum PEG-BILS formulation, containing PL:SDC ratio (5:1), 5 mg cholesterol, and 30 min sonication, yielded spherical vesicles in the nanoscale (200±15.2 nm), elevated percent of entrapment efficiency (95.5±7.77%), and a sustained release profile of DAC with 35.11±2.3% release. In vivo and drug distribution studies revealed an enhanced hepatocellular delivery of DAC-loaded PEG-BILS compared to DAC-unPEG-BILS and DAC suspension, where DAC-PEG-BILS achieved 1.19- and 1.54 times the AUC0-24 of DAC-unPEG-BILS and DAC suspension, respectively. Compared with DAC-unPEG-BILS and DAC suspension, DAC-PEG-BILS delivered about 2 and 3 times higher DAC into the liver, respectively.

CONCLUSION

The innovative encapsulation of DAC-PEG-BILS has a great potential for liver targeting.

Recent advances in the chromatographic determination of the most commonly used anti-hepatitis C drug sofosbuvir and its co-administered drugs in human plasma

Sofosbuvir is a direct-acting antiviral drug that inhibits hepatitis C virus (HCV) NS5B polymerase, which in turn affects the virus replication inside biological systems. The clinical importance of sofosbuvir is based not only on its effect on HCV but also on other lethal viruses such as Zika and severe acute respiratory syndrome coronavirus disease 2019 (SARS-COVID-19). Accordingly, there is a continuous shedding of light on the development and validation of accurate and fast analytical methods for the determination of sofosbuvir in different environments. This work critically reviews the recent advances in chromatographic methods for the analysis of sofosbuvir and/or its metabolites in pure samples, pharmaceutical dosage forms, and in the presence of other co-administered drugs to highlight the current status and future perspectives to enhance its determination in different matrixes.

Development and validation of RP HPLC method for the estimation of Sofosbuvir and related impurity in bulk and pharmaceutical dosage form

Background

The present work is aimed at development and validation of RP HPLC method which is simple, specific, precise, and accurate for estimation of Sofosbuvir and its process-related impurity in bulk and pharmaceutical dosage forms. Extensive literature survey revealed no method for estimation of the above said. The chromatographic separation was achieved on Agilent Eclipse XDB-C18, 4.6 × 250 mm, 5 μm with mobile phase composed of 0.1% trifluoroacetic acid in 1000 ml of water:acetonitrile (50:50) using an isocratic mode of elution. Detection was made using UV detector at 260.0 nm and LC solution software for analysis of data. The developed method was validated according to ICH guidelines.

Results

The linearity of calibration curve for Sofosbuvir in concentration range of 160-480 μg/ml was good. The curve was linear for its process related impurity (Phosphoryl) in concentration range of 10-30 μg/ml. There exists a good correlation between peak area and analyte concentration. Retention time for Sofosbuvir was found to be 3.674 min and its impurity was 5.704 min. Relative standard deviation values for Sofosbuvir is 1.741 and its process related impurity is 0.043. LOD for Sofosbuvir and its impurity was found to be 0.01% (0.04 μg) and 0.03% (0.12 μg) respectively. LOQ for Sofosbuvir and its impurity was found to be 0.50% (0.125 μg) and 1.50% (0.375 μg) respectively.

Conclusion

All the results reveal that the proposed method was found to be highly sensitive, simple, precise, accurate, robust, and fast. Large number of samples can be analyzed in shorter time due to shorter retention times, so it can be successfully applied for routine analysis of Sofosbuvir and related phosphoryl impurity in bulk and pharmaceutical dosage forms.

Feasible TLC-Spectro-Densitometry Technique for Simultaneous Determination of Two Hepatitis C Antiviral Drugs, Sofosbuvir and Simeprevir: Application to Combined Pharmaceutical Dosage Forms and Human Plasma

A high-performance thin-layer chromatographic method was developed and validated for the concurrent determination of simeprevir (SMV) and sofosbuvir (SOF). The chromatographic separation was attained on silica gel 60 F254 as stationary phase and ethyl acetate-hexane-methanol (5.0:4.0:1.0, v/v/v) as developing solvent with UV detection at 273 nm. The RF values were 0.67±0.02 and 0.43±0.02 for SMV and SOF, respectively. The method has been validated in respect to the guidelines of the International Conference on Harmonization. Linearity was maintained between 60-1,000 and 70-1,200 ng/band for SMV and SOF, respectively, with good correlation coefficients (0.9993-0.9997) for both drugs. The suggested method was highly sensitive as the calculated detection limits were 15 and 22 ng/band, while the quantitation limits were 44 and 66 ng/ band for SMV and SOF, respectively. The suggested methodology has been effectively employed for the determination of the mentioned drugs in their pure forms and their pharmaceutical dosage forms as well as human plasma without significant interference of the pharmaceutical excipients or plasma components.

Analytical Methods for Determination of Antiviral Drugs in Different Matrices: Recent Advances and Trends

Viruses are the main pathogenic substances that cause severe diseases in humans and other living things. They are among the most common microorganisms, and consequently, antiviral drugs have emerged to prevent and treat viral infections. Antiviral drugs are an essential drug group considering their prescription and consumption rates for different diseases and indications. Therefore, it is crucial to develop accurate and precise analytical methods to detect antiviral drugs in various matrices. Chromatographic techniques are used frequently for the quantification purpose since they allow simultaneous determination of antivirals. Electrochemical methods have also gained importance since the analysis can be performed quickly without the need for pretreatment. Spectrophotometric and spectrofluorimetric methods are used because they are simple, inexpensive, and less time-consuming methods. The purpose of this review is to present an overview of the analysis of currently used antiviral drugs from 2010 to 2021. Since studies on antiviral drugs are numerous, selected publications were reviewed in this article. The analysis of antiviral drugs was divided into three main groups: chromatographic, spectrometric, and electrochemical methods which were applied to different matrices, including pharmaceutical, biological, and environmental samples.

Rapid and sensitive UHPLC-DAD method for simultaneous determination of sofosbuvir and ledipasvir in human serum

Today, the direct-acting antiviral agents (DAAs) such as sofosbuvir (SOF) and ledipasvir (LED) are widely used to treat the hepatitis virus infection. The aim of this study was to develop a rapid, simple and valid method for simultaneous determination of SOF and LED in human plasma for bioavailability and pharmacokinetic studies. Chromatographic analysis was performed on the C₁₈ column (Blue Orchid, 1.8 μm, 50 × 2 mm) using 0.1 % formic acid in water (pH 2.6) and acetonitrile (60:40; v/v) as mobile phase at a flow rate of 0.5 mL/min. The UV detector was set at 328 nm and 260 nm for analysis of SOF and LED, respectively. To 400 μL of plasma, 100 μL of clonazepam as the internal standard (I.S, 7 μg/mL) was added and the mixture subjected to liquid-liquid extraction using 1000 μL diethyl ether. The calibration curves were linear with coefficients of variation less than 8% for all analyses. The limit of quantification (LOQ) was 20 and 5 ng/mL for SOF and LED, respectively. The results of inter-day and intra-day precision showed good reproducibility and the total analysis time was 1.2 min. This method successfully applied for determination SOF and LED in four healthy volunteers.

Validated Reversed-Phase Liquid Chromatographic Method with Gradient Elution for Simultaneous Determination of the Antiviral Agents: Sofosbuvir, Ledipasvir, Daclatasvir, and Simeprevir in Their Dosage Forms

A simple, rapid, sensitive, and precise reversed-phase liquid chromatographic method was developed and validated for the simultaneous determination of four direct-acting antivirals, sofosbuvir (SF), ledipasvir (LD), declatasvir (DC), and simeprevir (SM), in their respective pharmaceutical formulations. Effective chromatographic separation was achieved on an Agilent Eclipse plus C8 column (250 mm × 4.6 mm, 5 µm) at 40 °C with gradient elution using a mobile phase composed of acetonitrile:phosphate buffer (pH 6.5). The quantification of SF and DC was based on peak area measurements at 260 nm, while the quantification of LD and SM was achieved at 330 nm. The linearity was acceptable from 1.0 to 20.0 μg/mL for the studied drugs, with correlation coefficients >0.999. The analytical performance of the newly proposed HPLC procedure was thoroughly validated according to ICH guidelines in terms of linearity, precision (RSD%, 0.39-1.57), accuracy (98.05-101.90%), specificity, limit of detection (LOD) (0.022-0.039 μg/mL), limit of quantification (LOQ) (0.067-0.118 μg/mL), and robustness. The validated HPLC method was successfully used to analyze the abovementioned drugs in their pure and dosage forms without interference from common excipients present in commercial formulations.

Micelle sensitized synchronous spectrofluorimetric approaches for the simultaneous determination of simeprevir and ledipasvir: Application to pharmaceutical formulations and human plasma

Simeprevir (SMV) is commonly co-administered with ledipasvir (LDS) and sofosbuvir (SOF) as an effective combination regimen for treatment naive hepatitis C virus infected patients. In the present study, two spectrofluorimetric approaches were combined together for the development of highly sensitive, rapid, simple and accurate method for simultaneous quantification of SMV and LDS. The native fluorescence intensity values of SMV and LDS were enhanced by the addition of Tween-80 micellar system, while second derivative of the synchronous fluorescence intensity of the drugs at Δλ = 120 nm enabled the determination of both drug concomitantly. Different experimental parameters affecting the synchronous fluorescence of the cited drugs were carefully evaluated for their optimization. The peak amplitudes of the second derivative synchronous fluorimetry were measured at 429 nm for SMV and at 417 nm for LDS. The fluorescence-concentration plots were rectilinear over the range of 60-1500 and 36-540 ng mL^-1 with lower detection limits of 9.0 and 6.0 ng mL^-1 and quantification limits of 27.0 and 17.0 ng mL^-1 for SMV and LDS respectively. The method was successfully applied for the determination of both drugs in their pure forms as well as their pharmaceutical products and human plasma without any significant interference. Statistical comparison with the reported method revealed excellent accuracy and precision of the proposed method.

Modification of N,S co-doped graphene quantum dots with p-aminothiophenol-functionalized gold nanoparticles for molecular imprint-based voltammetric determination of the antiviral drug sofosbuvir

A molecularly imprinted polymer (MIP) was developed for the electrochemical determination of the antiviral drug sofosbuvir (SOF). The MIP was obtained by polymerization of p-aminothiophenol (p-ATP) on N,S co-doped graphene quantum dots (N,S@GQDs) in the presence of gold nanoparticles to form gold-sulfur covalent network. The presence of quantum dots improves the electron transfer rate, enhances surface activity and amplifies the signal. The nanocomposites were characterized by FTIR, TEM, EDX, and SEM. The electrochemical performance of the electrode was investigated by differential pulse voltammetry and cyclic voltammetry. The sensor uses hexacyanoferrate as the redox probe and is best operated at a potential of around 0.36 V vs. Ag/AgCl. It has a linear response over the concentration range of 1-400 nM SOF, with a detection limit of 0.36 nM. Other features include high selectivity, good reproducibility and temporal stability. The sensor was applied to the determination of SOF in spiked human plasma. Graphical abstract Novel sofosbuvir imprinted p-ATP polymer was synthesized by the aid of gold nanoparticles on N,S co-doped graphene quantum dots as a good conductive support. The imprinted polymer was used for detection of sofosbuvir in real samples by using the ferri/ferrocyanide redox probe.

Determination of sofosbuvir with two co-administered drugs; paracetamol and DL-methionine by two chromatographic methods. Application to a pharmacokinetic study

AIM

Two rapid and sensitive chromatographic methods have been developed and validated for simultaneous analysis of sofosbuvir (SOF) in rat plasma with two co-administered drugs, paracetamol (PAR) and DL-methionine (MET).

MATERIALS & METHODS

The first method relied on using TLC-densitometry with a developing system consisted of chloroform: methanol: glacial acetic acid: formic acid in the ratio of 9.5: 1: 1.5: 0.5, by volume. The studied analytes and the internal standard naphazoline hydrochloride were scanned at 210 nm. The second method was HPLC method, whereas the analytes and the internal standard cinnarizine were separated on XTerra^® HPLC RP C18 column using gradient elution mode and a mobile phase consisted of methanol: 0.1% aqueous TEA at pH 3 adjusted with orthophosphoric acid at 210 nm.

RESULTS

The TLC-densitometry method showed linearity over concentration ranges of 160-3000 ng/band for SOF and PAR, 300-3000 ng/band for MET, but HPLC method was linear and validated over concentration ranges of 150-5000 ng/ml for SOF, 300-5000 ng/ml for both PAR and MET.

CONCLUSION

All validation parameters met the acceptance criteria according to US FDA guidelines. Pharmacokinetic study was successfully applied and proved the possibility of co-administration of SOF with PAR and MET.

Earth-friendly spectrophotometric methods for simultaneous determination of ledipasvir and sofosbuvir: Application to average content and uniformity of dosage unit testing

Simple, rapid, sensitive, accurate, precise and earth-friendly spectrophotometric methods were developed for the simultaneous analysis of ledipasvir (LED) and sofosbuvir (SOF) without interference of both sunset yellow dye and copovidone excipients (the most probable interferents) in their combined dosage form. These proposed methods were based on measurement of LED in synthetic mixtures and combined dosage form by first derivative (¹D) spectrophotometry at 314 nm over the concentration range of 2-50 μg mL^-1 with coefficient of determination (R²) > 0.9999, mean percentage recovery of 99.98 ± 0.62. On the other hand, SOF in synthetic mixtures and combined dosage form was determined by five methods. Method I is based on the use of ¹D spectrophotometry at 274.2 nm (zero crossing point of LED). Method II involves the application of conventional dual wavelength method (DW) at the absolute difference between SOF zero order amplitudes at 261 nm (λ_max of SOF) and 364.7 nm. At these wavelengths, the absolute difference between LED zero order amplitudes was observed to equal zero. Method III depends on isosbestic point method (ISP) in which the total concentration of both drugs was measured at isosbestic point at 262.7 nm. Concentration of SOF could be obtained by subtraction of LED concentration. While, method IV depends on absorbance correction method (absorption factor method), which is based on determination of SOF concentration at 262.7 nm (λ_ISP) and LED at 333 nm (λ_max of LED). Finally, method V depends on absorbance ratio method (Q-analysis) in which 262.7 nm (λ_ISP) and 261 nm (λ_max of SOF) were selected to determine SOF concentration. The linearity range for all methods for SOF determination was 2-50 μg mL^-1 with coefficient of determination (R²) > 0.9999. Methods I, II & III were also applied for determination of SOF concentration in single dosage form. Their mean percentage recoveries were 100.35 ± 1.85, 99.97 ± 0.54 and 100.03 ± 0.49, for the three methods respectively. The proposed methods were validated according to international conference of harmonization (ICH) requirements and statistically compared to published reference methods. The ANOVA test confirmed that there is no significant differences between the proposed methods, and can be used for routine analysis of LED and SOF in commercial tablets. These developed methods were applied to estimate the average content and uniformity of dosage unit for LED/SOF combined dosage form and SOF single dosage form according to British pharmacopeia (BP) requirements.

Specific stability indicating spectrofluorimetric method for determination of ledipasvir in the presence of its confirmed degradation products; application in human plasma

A rapid and specific spectrofluorimetric method with higher sensitivity was developed for determination of ledipasvir (LDS) in tablets and human plasma. The proposed method relies on hydrogen bonding formations between the hydroxyl groups of polyoxyethylene 50 stearate and LDS, causing significant enhancement of its native fluorescence. The fluorescence intensity was measured at 430 nm after excitation at 340 nm. The fluorescence-concentration plot was rectilinear over the range 1-400 ng mL^-1 with detection and quantification limits of 0.25 and 1.10 ng mL^-1, respectively. The high sensitivity of the proposed method permits its application for ledipasvir determinations in real human plasma even in the presence of co-administered drugs sofosbuvir and ribavirin. Moreover, the proposed method was further extended to stability studies of ledipasvir after exposure to different forced degradation conditions according to ICH guidelines, along with the structural elucidation of its degradation products utilizing IR and Mass spectra. A proposal for the degradation pathways was presented.

Development of a highly sensitive high-performance thin-layer chromatography method for the screening and simultaneous determination of sofosbuvir, daclatasvir, and ledipasvir in their pure forms and their different pharmaceutical formulations

The combination of sofosbuvir and daclatasvir or sofosbuvir and ledipasvir is now widely used as an ideal treatment for hepatitis C virus infection. For this purpose, a simple, sensitive, accurate, economic, and precise high-performance thin-layer chromatography was developed and validated for the determination of sofosbuvir, daclatasvir, and ledipasvir in their pure form as well as their different pharmaceutical products. The method used Merck high-performance thin-layer chromatography aluminum plates precoated with silica gel 60 F254 as a stationary phase and mobile phase consisting of methylene chloride/methanol/ethyl acetate/ammonia (25%) (6:1:4:1, v/v/v/v). This system was found to give compact symmetric peaks of sofosbuvir, daclatasvir, and ledipasvir with retardation factors of 0.27 ± 0.01, 0.50 ± 0.007, and 0.68 ± 0.008, respectively. The densitometric scanner was set at 275 nm using a deuterium lamp. The calibration curves were linear over the range of 100-3000 ng/spot for sofosbuvir, and daclatasvir, and range of 50-3000 ng/spot for ledipasvir. The detection limits were 22.5, 31.90, and 15.80 for sofosbuvir, daclatasvir, and ledipasvir. The quantitation limits were 67.50, 95.60, and 47.50 for sofosbuvir, daclatasvir, and ledipasvir. The proposed method was validated according to International Conference on Harmonization (ICH) guidelines and the results were acceptable.

New, simple and sensitive HPTLC method for simultaneous determination of anti-hepatitis C sofosbuvir and ledipasvir in rabbit plasma

Sofosbuvir (SOF) and ledipasvir (LDS) represent anti-hepatitis C binary mixture. Herein, a fast high-performance thin-layer chromatography (HPTLC) method was developed, validated and applied for simultaneous determination of SOF and LDS in biological matrix. An innovative strategy was designed which based on coupling dual wavelength detection with HPTLC. This strategy enabled sensitive, specific, high sample throughput and cost-effective determination of the SOF-LDS binary mixture. The developed HPTLC procedure is based on a simple liquid-liquid extraction, enrichment of the analytes and subsequent separation with UV detection. Separations were performed on HPTLC silica gel 60 F₂₅₄ aluminum plates with a mobile phase consisting of ethyl acetate-glacial acetic acid (100:5, v/v). The R_f values for SOF and LDS were 0.62 and 0.30, respectively. Dual wavelength scanning was carried out in the absorbance mode at 265 and 327 nm for SOF and LDS, respectively. The linear ranges were 40-640 and 9-144 ng/band for SOF and LDS, respectively with correlation coefficients of 0.9998. The detection limits were 10.61 and 2.54 ng/band and the quantitation limits were 32.14 and 7.70 ng/band for SOF and LDS, respectively indicating high sensitivity of the proposed method. Consequently, this permits in vitro and in vivo application of the proposed method in rabbit plasma with good percentage recovery (95.68-103.26%). Validation parameters were assessed according to ICH guidelines. The proposed method represents a simple, high sample throughput and economic alternative to the already existing more complicated reported LC-MS/MS techniques. The method would afford an efficient tool for therapeutic drug monitoring and bioavailability studies of SOF and LDS.

Chemometric simultaneous determination of Sofosbuvir and Ledipasvir in pharmaceutical dosage form

Partial least squares (PLS), different families of continuous wavelet transform (CWT), and first derivative spectrophotometry (DS) techniques were studied for quantification of Sofosbuvir (SFB) and Ledipasvir (LDV) simultaneously without separation step. The components were dissolved in Acetonitrile and the spectral behaviors were evaluated in the range of 200 to 400nm. The ultraviolet (UV) absorbance of LDV exhibits no interferences between 300 and 400nm and it was decided to predict the LDV amount through the classic spectrophotometry (CS) method in this spectral region as well. Data matrix of concentrations and calibrated models were developed, and then by applying a validation set the accuracy and precision of each model were studied. Actual concentrations versus predicted concentrations plotted and good correlation coefficients by each method resulted. Pharmaceutical dosage form was quantified by developed methods and the results were compared with the High Performance Liquid Chromatography (HPLC) reference method. Analysis Of Variance (ANOVA) in 95% confidence level showed no significant differences among methods.

Comparison between core-shell and totally porous particle stationary phases for fast and green LC determination of five hepatitis-C antiviral drugs

The performances of core-shell 2.7 μm and fully porous sub-2 μm particles packed in narrow diameter columns were compared under the same chromatographic conditions. The stationary phases were compared for fast separation and determination of five new antiviral drugs; daclatasvir, sofosbuvir, velpatasvir, simeprevir, and ledipasvir. The gradient elution was done using ethanol as green organic modifier, which is more environmentally friendly. Although both columns provided very good resolution of the five drugs, core-shell particles had proven to be of better efficiency. Under gradient elution conditions, core-shell particles exhibited faster elution, better peak shape, and enhanced resolution adding to lower system backpressure. The column backpressure on sub-2 μm particles was more than twice that on core-shell particles. This gives a chance to use conventional high-performance liquid chromatography conditions without needing special instrumentation as that required for ultra-high performance liquid chromatography. The method was validated for determination of the five drugs by gradient elution using mobile phase composed of organic modifier ethanol and aqueous part containing 0.75 g sodium octane sufonate and 3.0 g sodium dihydrogen phosphate per liter at pH of 6.15. Detection was done using UV-detector set at 210 nm. The linearity, accuracy, and precision were found very good within the concentration range of 2-200 μg/mL.

A new innovative spectrophotometric method for the simultaneous determination of sofosbuvir and ledipasvir

A new innovative spectrophotometric method is developed to determine the concentration ratios in binary mixtures by determining the zero crossing point in the first derivative of the gross curve. This relationship can be applied if the part of the UV spectrum of substance Y, that intersects with the overlaid spectra of substance X is straight. By plotting the intersection wavelength against the concentration ratio (C_xC_y), a straight line was obtained with a co-efficient of determination equals 0.9999. As an application, simultaneous determination of sofosbuvir and ledipasvir in their binary mixtures was performed using two methods; a direct UV spectrophotometric method for determination of ledipasvir at 333nm, and the new "wavelength-intersection ratio" method for determination of sofosbuvir. In the wavelength-intersection ratio method, different mixtures of sofosbuvir and ledipasvir containing different concentration ratios were prepared; the zero crossing point of the first derivative curve in the range 285 to 295nm were determined for each mixture. An absorbance shift in the intersection was obtained with the change in the concentration ratio (sofosbuvir/ledipasvir). When the concentration ratio was plotted against the intersection wavelength, a straight line was obtained with a coefficient of determination of 0.9992. The direct method was linear in the range 3 to 18μg/mL while the wavelength-intersection ratio method was linear in the range 11-110μg/mL. The limits of detection were determined and found to be 0.5 and 3μg/mL for ledipasvir and sofosbuvir, respectively. The accuracy and repeatability of the two methods were tested. The mean %recovery was found to be 100.19% and 100.75% for ledipasvir and sofosbuvir, respectively. The relative standard deviation was 0.57 for ledipasvir and 1.79 for sofosbuvir. The intermediate precision was also checked, the coefficients of variation for sofosbuvir and ledipasvir measurements between days did not exceed 1.88%.

Validated spectrophotometric and chromatographic methods for analysis of the recently approved hepatitis C antiviral combination ledipasvir and sofosbuvir

This work describes five simple and reliable spectrophotometric and chromatographic methods for analysis of hepatitis C antiviral binary mixture of ledipasvir (LPV) and sofosbuvir (SBV). Method I is based on the use of A_max and derivative spectrophotometry with the zero-crossing technique where LPV was determined using its A_max and ¹D amplitudes at 324 and 338nm respectively, while SBV was determined by measuring the ¹D amplitudes at 276nm. Method II involves the application of the ratio spectra derivative spectrophotometry. For LPV, 12μg/mL SBV was used as divisor and the ¹DD amplitudes at 239.8nm were plotted against LPV concentrations; while by using 10μg/mL LPV, the amplitudes at 279.2nm were found proportional to SBV concentrations. Method III depends on ratio-difference measurement where the peak to trough amplitudes between 229.2 and 268.4nm were measured and correlated to LPV concentration. Similarly, the amplitudes between 268.6 and 229.2nm in the SBV ratio spectra were recorded. For method IV, the two compounds were separated using HPTLC sheets of silica gel and a mobile phase composed of chloroform-methanol (94:6) followed by densitometric measurement of LPV and SBV spots at 331 and 267nm respectively. Method V depends on HPLC-DAD. Effective chromatographic separation was achieved using Thermohypersil C8 column (4.6×250mm, 5μm) with a mobile phase consisting of 0.01M sodium dihydrogen phosphate (pH 2.5) and methanol (20:80) at a flow rate 1.2mL/min and detection at 332 and 262nm for LPV and SBV respectively. Analytical performance of the developed methods was validated according to the ICH guidelines with respect to linearity, ranges, precision, accuracy, detection and quantification limits. The validated methods were successfully applied to the simultaneous analysis of LPV and SBV in mixtures of different proportions and their combined tablet dosage form.

Simultaneous determination of the brand new two-drug combination for the treatment of hepatitis C: Sofosbuvir/ledipasvir using smart spectrophotometric methods manipulating ratio spectra

In this work, various sensitive and selective spectrophotometric methods were first introduced for the simultaneous determination of sofosbuvir and ledipasvir in their binary mixture without preliminary separation. Ledipasvir was determined simply by zero-order spectrophotometric method at its λ_max=333.0nm in a linear range of 2.5-30.0μg/ml without any interference of sofosbuvir even in low or high concentrations and with mean percentage recovery of 100.05±0.632. Sofosbuvir can be quantitatively estimated by one of the following smart spectrophotometric methods based on ratio spectra developed for the resolution of the overlapped spectra of their binary mixture; ratio difference spectrophotometric method (RD) by computing the difference between the amplitudes of sofosbuvir ratio spectra at 228nm and 270nm, first derivative (DD¹) of ratio spectra by measuring the sum of amplitude of trough and peak at 265nm and 277nm, respectively, ratio subtraction (RS) spectrophotometric method in which sofosbuvir can be successfully determined at its λ_max=261.0nm and mean centering (MC) of ratio spectra by measuring the mean centering values at 270nm. All of the above mentioned spectrophotometric methods can estimate sofosbuvir in a linear range of 7.5-90.0μg/ml with mean percentage recoveries of 100.57±0.810, 99.92±0.759, 99.51±0.475 and 100.75±0.672, respectively. These methods were successfully applied to the analysis of their combined dosage form and bulk powder. The adopted methods were also validated as per ICH guidelines and statistically compared to an in-house HPLC method.

Potential of RP-UHPLC-DAD-MS for the qualitative and quantitative analysis of sofosbuvir in film coated tablets and profiling degradants

Sofosbuvir is one of the new direct-acting antiviral drugs against hepatitis C virus (HCV) infection. This drug has recently been launched into the market, and generic versions of the medication are expected to be produced by local drug producers in some countries. Therefore, new methods are required to control sofosbuvir in pharmaceuticals. In the present study, a new method based on reversed phase (RP)-ultra-high performance liquid chromatography (UHPLC) coupled to diode array detection (DAD) and mass spectrometry (MS) was developed to facilitate the qualitative and quantitative analysis of sofosbuvir in film coated tablets. A wavelength of 260 nm was selected to perform a cost-effective quantification and the method showed adequate linearity, with an R2 value of 0.9998, and acceptable values of accuracy (75%-102%) and precision (residual standard deviation <5%). The detection and quantification limits were 0.07 μg/mL and 0.36 μg/mL, respectively. Furthermore, the use of high-resolution MS enabled us to ensure the specificity, check impurities and better sensitivity. Therefore, this methodology promises to be suitable not only for the routine analysis of sofosbuvir in pharmaceutical dosage forms, but also for potential degradants.