Microactuator device for integrated measurement of epithelium mechanics

MEMS device for applying shear and tension to an epithelium combined with fluorescent live cell imaging

Mechanical forces play important roles in the biological function of cells and tissues. While numerous studies have probed the force response of cells and measured cell-generated forces, they have primarily focused on tensile, but not shear forces. Here, we describe the design, fabrication, and application of a silicon micromachined device that is capable of independently applying and sensing both tensile and shear forces in an epithelial cell monolayer. We integrated the device with an upright microscope to enable live cell brightfield and fluorescent imaging of cells over many hours following mechanical perturbation. Using devices of increasing stiffness and the same displacement input, we demonstrate that epithelia exhibit concomitant higher maximum resistive tensile forces and quicker force relaxation. In addition, we characterized the force response of the epithelium to cyclic shear loading. While the maximum resistive forces of epithelia under cyclic shear perturbation remained unchanged between cycles, cyclic loading led to faster relaxation of the resistive forces. The device presented here can be applied to studying the force response of other monolayer-forming cell types and is compatible with pharmacological perturbation of cell structures and functions.

Shear-induced damped oscillations in an epithelium depend on actomyosin contraction and E-cadherin cell adhesion

Shear forces between cells occur during global changes in multicellular organization during morphogenesis and tissue growth, yet how cells sense shear forces and propagate a response across a tissue is unknown. We found that applying exogenous shear at the midline of an epithelium induced a local, short-term deformation near the shear plane, and a long-term collective oscillatory movement across the epithelium that spread from the shear-plane and gradually dampened. Inhibiting actomyosin contraction or E-cadherin trans-cell adhesion blocked oscillations, whereas stabilizing actin filaments prolonged oscillations. Combining these data with a model of epithelium mechanics supports a mechanism involving the generation of a shear-induced mechanical event at the shear plane which is then relayed across the epithelium by actomyosin contraction linked through E-cadherin. This causes an imbalance of forces in the epithelium, which is gradually dissipated through oscillatory cell movements and actin filament turnover to restore the force balance across the epithelium.

MEMS measurements of single cell stiffness decay due to cyclic mechanical loading

The goal of this study was to measure the mechanical stiffness of individual cells and to observe changes due to the application of repeated cell mechanical loads. 28 single baker's yeast cells (Saccharomyces cerevisiae) were fatigue tested and had their stiffness measured during repetitive loading cycles performed by a MEMS squeezer in aqueous media. Electrothermal micro-actuators compressed individual cells against a reference back spring; cell and spring motions were measured using a FFT image analysis technique with ~10 nm resolution. Cell stiffness was calculated based on measurements of cell elongation vs. applied force which resulted in stiffness values in the 2-10 N/m range. The effect of increased force was studied for cells mechanically cycled 37 times. Cell stiffness decreased as the force and the cycle number increased. After 37 loading cycles (~4 min), forces of 0.24, 0.29, 0.31, and 0.33 μN caused stiffness drops of 5%, 13%, 31% and 41% respectively. Cells force was then set to 0.29 μN and cells were tested over longer runs of 118 and 268 cycles. After 118 cycles (~12 min) cells experienced an average stiffness drop of 68%. After 268 cycles (~25 min) cells had a stiffness drop of 77%, and appeared to reach a stiffness plateau of 20-25% of the initial stiffness after approximately 200 cycles.

A simple multi-well stretching device to induce inflammatory responses of vascular endothelial cells

We herein introduce a novel multi-well stretching device that is made of three polydimethylsiloxane layers, consisting of a top hole-punched layer, middle thin membrane, and bottom patterned layer. It is the first time that such a simple device has been used to supply axisymmetric and nonuniform strains to cells cultured on well bottoms that are stretchable. These mechanical stimuli can somewhat mimic the stretching at the bending sites of blood vessels, where the strains are complicated. In this device, nonuniform strain is given to cells through the deformation of a membrane from a flat surface to a spherical cap during the injection of a certain volume of water into the chamber between the middle membrane and bottom layer. EA.hy926 cells (a human umbilical vein endothelial cell line) were seeded on the well bottoms and exposed to axisymmetric strain under a 5, 10, 15, and 20% degree of deformation of the membrane. The cellular responses were characterized in terms of cell morphology, cell viability, and expression of inflammatory mRNAs and proteins. With increasing the degree of deformation, the cells exhibited an inclination toward detachment and apoptosis; meanwhile the expression of inflammatory mRNAs and proteins, such as MCP-1, IL-8, IL-6 and ICAM-1, showed a significant increment. The obtained results demonstrate that the inflammatory responses of EA.hy926 cells can be induced by increasing the magnitude of the strain. This simple device provides a useful tool for in vitro investigation of the inflammatory mechanisms related to vascular diseases.

Fabricated micro-nano devices for in vivo and in vitro biomedical applications

In recent years, the innovative use of microelectromechanical systems (MEMSs) and nanoelectromechanical systems (NEMSs) in biomedical applications has opened wide opportunities for precise and accurate human diagnostics and therapeutics. The introduction of nanotechnology in biomedical applications has facilitated the exact control and regulation of biological environments. This ability is derived from the small size of the devices and their multifunctional capabilities to operate at specific sites for selected durations of time. Researchers have developed wide varieties of unique and multifunctional MEMS/NEMS devices with micro and nano features for biomedical applications (BioMEMS/NEMS) using the state of the art microfabrication techniques and biocompatible materials. However, the integration of devices with the biological milieu is still a fundamental issue to be addressed. Devices often fail to operate due to loss of functionality, or generate adverse toxic effects inside the body. The in vitro and in vivo performance of implantable BioMEMS such as biosensors, smart stents, drug delivery systems, and actuation systems are researched extensively to understand the interaction of the BioMEMS devices with physiological environments. BioMEMS developed for drug delivery applications include microneedles, microreservoirs, and micropumps to achieve targeted drug delivery. The biocompatibility of BioMEMS is further enhanced through the application of tissue and smart surface engineering. This involves the application of nanotechnology, which includes the modification of surfaces with polymers or the self-assembly of monolayers of molecules. Thereby, the adverse effects of biofouling can be reduced and the performance of devices can be improved in in vivo and in vitro conditions.