Corrosion, mechanical and bioactivity properties of HA-CNT nanocomposite coating on anodized Ti6Al4V alloy

Application of Hydroxyapatite Composites in Bone Tissue Engineering: A Review

The treatment of bone defects is complicated by clinical conditions, such as trauma, tumor resection, and infection, which result in defects and impair the bone's regenerative capacity. Hydroxyapatite (HAp), the primary inorganic component of bone, possesses good biocompatibility and osteoconductivity. However, it has poor mechanical properties, a slow degradation rate, and limited functionality, necessitating combination with other materials to broaden its application scope. This paper summarizes the importance and properties of HAp composites and provides a categorized review of current research on HAp composites in bone tissue engineering. These composite scaffolds not only offer excellent mechanical support for cell growth and tissue regeneration but also facilitate new bone formation and vascularization. Additionally, the challenges faced by HAp composites, such as material property optimization and improvement of preparation techniques, are discussed. The paper also summarizes the applications of HAp composites in bone defect repair, dental implants, spinal fusion, and other fields.

The effect of silver nanoparticles on biological and corrosion behavior of electrophoretically deposited hydroxyapatite film on Ti6Al4V

Surface modification of titanium and its alloys has been seriously considered by researchers to improve their biological behaviors, in the past few decades. In present research, hydroxyapatite (HA) based composite coatings with different concentrations of 0, 2, 4, and 6 wt% of silver (Ag) nanoparticles were electrophoretically deposited (EPD) on anodized and non-anodized Ti6Al4V, using a direct current at a voltage of 30 V for 10 min at room temperature. The specimens were then characterized by means of X-ray diffraction (XRD) analysis, Fourier transform infrared spectroscopy (FT-IR), scanning electron microscopy (SEM) equipped with energy dispersive spectroscopy (EDS). The cell adhesion images and cell viability results showed that HA-Ag composite coatings significantly promoted the biocompatibility of samples compared with the non-anodized and anodized Ti6Al4V. The viabilities of Mg-63 cells on HA-4%Ag coating and bi-layer coating (HA-4%Ag on anodized specimen) were approximately 91% and they were considered as the best coatings in term of biocompatibility. On the other hand, the antibacterial assessments demonstrated that HA-6%Ag coating had the best antibacterial performance compared with other samples. Furthermore, Tafel polarization curves indicated that corrosion resistance of the bi-layer coating was higher than those of the other specimens. The polarization resistance of this coating was about 7 times more than that of theTi6Al4V alloy.

Evaluation of Time-Dependent Corrosion Inhibition Rate for f-MWCNT-BCP Composite Coatings on 316L Stainless Steel in Simulated Body Fluid for Orthopedic Implantation

A well-developed-multiwall carbon nanotube (f-MWCNT)/biphasic calcium phosphate (BCP) composites were synthesized using ultrasonication method for orthopedic implantation applications. The formation of composites and its phase was confirmed by using X-ray diffraction. The presence of various functional groups was identified by using Fourier transform infra-red (FT-IR) spectroscopy. The presence of f-MWCNT was confirmed by Raman spectroscopy. High-resolution transmission electron microscopy (HR-TEM) analysis revealed that BCP units were bound by the surface of f-MWCNTs. The synthesized composites were coated on medical grade 316L stainless steel substrates using electro deposition technique. To determine its corrosion resistance characteristics, the developed substrates were exposed to a simulated bodily fluid (SBF) solution for 0, 4, and 7 days. These results strongly suggest that the coated composites can be utilized for bone tissue repair.

Physical, mechanical, and biological performance of chitosan-based nanocomposite coating deposited on the polycaprolactone-based 3D printed scaffold: Potential application in bone tissue engineering

Recently, coating on composite scaffolds has attracted many researchers' attention to improve scaffolds' properties. In this research, a 3D printed scaffold was fabricated from polycaprolactone (PCL)/magnetic mesoporous bioactive glass (MMBG)/alumina nanowire (Al2O3, Optimal percentage 5 %) (PMA) and then coated with chitosan (Cs)/multi-walled carbon nanotubes (MWCNTs) by an immersion coating method. Structural analyses such as XRD and ATR-FTIR confirmed the presence of Cs and MWCNTs in the coated scaffolds. The SEM results of the coated scaffolds showed homogeneous three-dimensional structures with interconnected pores compared to the uncoated scaffolds. The coated scaffolds exhibited an increase in compression strength (up to 16.1 MPa) and compressive modulus (up to 40.83 MPa), improved surface hydrophilicity (up to 32.69°), and decrease in degradation rate (68 % remaining weight) compared to the uncoated scaffolds. The increase in apatite formation in the scaffold coated with Cs/MWCNTs was confirmed by SEM, EDAX, and XRD tests. Coating the PMA scaffold with Cs/MWCNTs leads to the viability and proliferation of MG-63 cells and more secretion of alkaline phosphatase and Ca activity, which can be introduced as a suitable candidate for use in bone tissue engineering.