Thorium adsorption by oxidized biochar fibres derived from Luffa cylindrica sponges

Thorium Removal, Recovery and Recycling: A Membrane Challenge for Urban Mining

Although only a slightly radioactive element, thorium is considered extremely toxic because its various species, which reach the environment, can constitute an important problem for the health of the population. The present paper aims to expand the possibilities of using membrane processes in the removal, recovery and recycling of thorium from industrial residues reaching municipal waste-processing platforms. The paper includes a short introduction on the interest shown in this element, a weak radioactive metal, followed by highlighting some common (domestic) uses. In a distinct but concise section, the bio-medical impact of thorium is presented. The classic technologies for obtaining thorium are concentrated in a single schema, and the speciation of thorium is presented with an emphasis on the formation of hydroxo-complexes and complexes with common organic reagents. The determination of thorium is highlighted on the basis of its radioactivity, but especially through methods that call for extraction followed by an established electrochemical, spectral or chromatographic method. Membrane processes are presented based on the electrochemical potential difference, including barro-membrane processes, electrodialysis, liquid membranes and hybrid processes. A separate sub-chapter is devoted to proposals and recommendations for the use of membranes in order to achieve some progress in urban mining for the valorization of thorium.

Addition of Phosphogypsum to Fire-Resistant Plaster Panels: A Physic–Mechanical Investigation

Gypsum (GPS) has great potential for structural fire protection and is increasingly used in construction due to its high-water retention and purity. However, many researchers aim to improve its physical and mechanical properties by adding other organic or inorganic materials such as fibers, recycled GPS, and waste residues. This study used a novel method to add non-natural GPS from factory waste (phosphogypsum (PG)) as a secondary material for GPS. This paper proposes to mix these two materials to properly study the effect of PG on the physico-mechanical properties and fire performance of two Tunisian GPSs (GPS1 and GPS2). PG initially replaced GPS at 10, 20, 30, 40, and 50% weight percentage (mixing plan A). The PGs were then washed with distilled water several times. Two more mixing plans were run when the pH of the PG was equal to 2.4 (mixing plan B), and the pH was equal to 5 (mixing plan C). Finally, a comparative study was conducted on the compressive strength, flexural strength, density, water retention, and mass loss levels after 90 days of drying, before/after incineration of samples at 15, 30, 45, and 60 min. The results show that the mixture of GPS1 and 30% PG (mixing plan B) obtained the highest compressive strength (41.31%) and flexural strength (35.03%) compared to the reference sample. The addition of 10% PG to GPS1 (mixing plan A) improved fire resistance (33.33%) and the mass loss (17.10%) of the samples exposed to flame for 60 min compared to GPS2. Therefore, PG can be considered an excellent insulating material, which can increase physico-mechanical properties and fire resistance time of plaster under certain conditions.

Efficient Removal of Polyvalent Metal Ions (Eu(III) and Th(IV)) from Aqueous Solutions by Polyurea-Crosslinked Alginate Aerogels

The removal of polyvalent metal ions Eu(III) and Th(IV) from aqueous solutions using polyurea-crosslinked calcium alginate (X-alginate) aerogels has been investigated by batch-type experiments under ambient conditions and pH 3. The material presents relatively high sorption capacity for Eu(III) (550 g kg⁻¹) and Th(IV) (211 g kg⁻¹). The lower sorption capacity for Th(IV) compared to Eu(III) is attributed to the net charge of the dominant species in solution under the given experimental conditions, which is Eu³⁺ for Eu(III), and Th(OH)₂²⁺ and Th(OH)₃⁺ for Th(IV). Generally, the sorption is an endothermic and entropy-driven process, and it follows the Langmuir isotherm model. According to the FTIR spectra, sorption occurs via formation of inner-sphere complexes between the surface functional groups and the f-metal cationic species. The presence of europium and thorium in the adsorbent material was confirmed and quantified with EDS analysis. To the best of our knowledge, this is the first report of an aerogel material used as an adsorbent for Eu(III). Compared to other materials used for the sorption of the specific ions, which are mostly carbon-based, X-alginate aerogels show by far the highest sorption capacity. Regarding Th(IV) uptake, X-alginate aerogels show the highest capacity per volume (27.9 g L⁻¹) among the aerogels reported in the literature. Both Eu(III) and Th(IV) could be recovered from the beads by 65% and 70%, respectively. Furthermore, Th(VI) could also be quantitatively removed from wastewater, while Eu(III) could be removed by 20%. The above, along with their stability in aqueous environments, make X-alginate aerogels attractive candidates for water treatment and metal recovery applications.