Efficient fluoride removal using Al-Cu oxide nanoparticles supported on steel slag industrial waste solid

Electrochemical sensors modified with iron oxide nanoparticles/nanocomposites for voltammetric detection of Pb (II) in water: A review

Permissible limits of Pb2+ in drinking water are being reduced from 10 μgL-1 to 5 μgL-1, which calls for rapid, and highly reliable detection techniques. Electrochemical sensors have garnered attention in detection of heavy metal ions in environmental samples due to their ease of operation, low cost, and rapid detection responses. Selectivity, sensitivity and detection capabilities of these sensors, can be enhanced by modifying their working electrodes (WEs) with iron oxide nanoparticles (IONPs) and/or their composites. Therefore, this review is an in-depth analysis of the deployment of IONPs/nanocomposites in modification of electrochemical sensors for detection of Pb2+ in drinking water over the past decade. From the analyzed studies (n = 23), the optimal solution pH, deposition potential, and deposition time ranged between 3 and 5.6, -0.7 to -1.4 V vs Ag/AgCl, and 100-400 s, respectively. Majority of the studies employed square wave anodic stripping voltammetry (n = 16), in 0.1 M acetate buffer solution (n = 19) for detection of Pb2+. Limits of detection obtained (2.5 x 10-9 - 4.5 μg/L) were below the permissible levels which indicated good sensitivities of the modified electrodes. Despite the great performance of these modified electrodes, the primary source of IONPs has always been commercial iron-based salts in addition to the use of so many materials as modifying agents of these IONPs. This may limit reproducibility and sustainability of the WEs due to lengthy and costly preparation protocols. Steel and/or iron industrial wastes can be alternatively employed in generation of IONPs for modification of electrochemical sensors. Additionally, biomass-based activated carbons enriched with surface functional groups are also used in modification of bare IONPs, and subsequently bare electrodes. However, these two areas still need to be fully explored.

Utilization of ferrous slags as coagulants, filters, adsorbents, neutralizers/stabilizers, catalysts, additives, and bed materials for water and wastewater treatment: A review

Solid waste is currently produced in substantial amounts by industrial activities. While some are recycled, the majority of them are dumped in landfills. Iron and steel production leaves behind ferrous slag, which must be created organically, managed wisely and scientifically if the sector is to remain more sustainably maintained. Ferrous slag is the term for the solid waste that is produced when raw iron is smelted in ironworks and during the production of steel. Both its specific surface area and porosity are relatively high. Since these industrial waste materials are so easily accessible and offer such serious disposal challenges, the idea of their reuse in water and wastewater treatment systems is an appealing alternative. There are many components such as Fe, Na, Ca, Mg, and silicon found in ferrous slags, which make it an ideal substance for wastewater treatment. This research investigates the potential of ferrous slag as coagulants, filters, adsorbents, neutralizers/stabilizers, supplementary filler material in soil aquifers, and engineered wetland bed media to remove contaminants from water and wastewater. Ferrous slag may provide a substantial environmental risk before or after reuse, so leaching and eco-toxicological investigations are necessary. Some study revealed that the amount of heavy metal ions leached from ferrous slag conforms to industrial norms and is exceedingly safe, hence it may be employed as a new type of inexpensive material to remove contaminants from wastewater. The practical relevance and significance of these aspects are attempted to be analyzed, taking into account all recent advancements in the fields, in order to help in the development of informed decisions about future directions for research and development related to the utilization of ferrous slags for wastewater treatment.

Iron oxide nanoparticles/nanocomposites derived from steel and iron wastes for water treatment: A review

Iron oxide nanoparticles (IONPs) are characterized by superior magnetic properties, high surface area to volume ratio, and active surface functional groups. These properties aid in removal of pollutants from water, through adsorption and/or photocatalysis, justifying the choice of IONPs in water treatment systems. IONPs are usually developed from commercial chemicals of ferric and ferrous salts alongside other reagents, a procedure that is costly, environmentally unfriendly and limits their mass production. On the other hand, steel and iron industries produce both solid and liquid wastes which in most cases are piled, discharged into water streams or landfilled as strategies to dispose them off. Such practices are detrimental to environmental ecosystems. Given the high content of iron present in these wastes, they can be used to generate IONPs. This work reviewed published literature through selected key words on the deployment of steel and/or iron-based wastes as IONPs precursors for water treatment. The findings reveal that steel waste-derived IONPs have properties such as specific surface area, particle sizes, saturation magnetization, and surface functional groups that are comparable or sometimes better than those synthesized from commercial salts. Furthermore, the steel waste-derived IONPs have high removal efficacy for heavy metals and dyes from water with possibilities of being regenerated. The performance of steel waste-derived IONPs can be enhanced by functionalization with different reagents such as chitosan, graphene, and biomass based activated carbons. Nonetheless, there is need to explore the potential of steel waste-based IONPs in removing contaminants of emerging concern, modifying pollutant detection sensors, their techno-economic feasibility in large treatment plants, toxicity of these nanoparticles when ingested into the human body, among other areas.

A critical review on adsorption and recovery of fluoride from wastewater by metal-based adsorbents

Rapid industrialization is deteriorating water quality, and fluoride pollution in water is one of the most serious environmental pollution problems. Adsorption technology is an efficient and selective process for removing fluoride from aqueous solutions using adsorbents. Metal-based adsorbents synergize the advantages of fast adsorption, high adsorption capacity, and excellent selectivity to effectively remove fluoride from water bodies, promising to satisfy environmental sustainability requirements. This paper reviews the metal-based adsorbents: iron-based, aluminum-based, lanthanum-based, cerium-based, titanium-based, zirconium-based, and multi-metal composite adsorbents, primarily focusing on the adsorption conditions and fluoride removal capacities and discusses prospects and challenges in the synthesis and application of metal-based adsorbents. This paper aims to stimulate new thinking and innovation in developing the next generation of sustainable adsorbents.

Removal of fluoride ions from aqueous solution by metaettringite

Fluoride contamination is a major problem in wastewater treatment. Metaettringite (which has previously shown enhanced anion adsorption) was investigated as a possible adsorbent to remove fluoride from low-concentration solution (25 mg-F/L). The fluoride removal properties of ettringite and metaettringite were first compared at pH 10, and metaettringite was found to be more effective. The dominant reaction mechanism for fluoride adsorption in metaettringite was found to be recrystallization of metaettringite by rehydration; this was accompanied by precipitation of calcium fluoride. The adsorption kinetics followed the pseudo-second order model. Metaettringite was also able to remove fluoride effectively in low pH environment (i.e., at pH 3.5). The influence of coexistence of sulfate ions in solution on the fluoride removal performance was investigated, and a small decrease in performance was noted. The residual fluoride concentrations obtained with higher doses of metaettringite were lower than those specified by the Japanese effluent standard (non-coastal areas: 8 mg-F/L; coastal areas: 15 mg-F/L). The fluoride removal capacity of metaettringite was compared with those of other solid materials. The observed maximum capacity was 174.7 mg-F/g-metaettringite. In the case of high fluoride concentration solution, the main removal mechanism will be changed to calcium fluoride precipitation. In general, metaettringite is regarded as promising material for fluoride removal in wastewater treatment.

Fluoride ions sorption using functionalized magnetic metal oxides nanocomposites: a review

Fluoride is an anionic pollutant found superfluous in surface or groundwater as a result of anthropogenic actions from improper disposal of industrial effluents. In drinking water, superfluous fluoride has been revealed to trigger severe health problems in humans. Hence, developing a comprehensive wastewater decontamination process for the effective management and preservation of water contaminated with fluoride is desirable, as clean water demand is anticipated to intensify considerably over the upcoming years. In this regard, there have been increased efforts by researchers to create novel magnetic metal oxide nanocomposites which are functionalized for the remediation of wastewater owing to their biocompatibility, cost-effectiveness, relative ease to recover and reuse, non-noxiousness, and ease to separate from solutions using a magnetic field. This review makes an all-inclusive effort to assess the effects of experimental factors on the sorption of fluoride employing magnetic metal oxide nanosorbents. The removal efficiency of fluoride ions onto magnetic metal oxides nanocomposites were largely influenced by the solution pH and ions co-existing with fluoride. Overall, it was noticed from the reviewed researches that the maximum sorption capacity using various metal oxides for fluoride sorption was in the order of aluminium oxides >cerium oxides > iron oxides > magnesium oxides> titanium oxides, and most sorption of fluoride ions was inhibited by the existence of phosphate trailed by sulphate. The mechanism of fluoride sorption onto various sorbents was due to ion exchange, electrostatic attraction, and complexation mechanism.

Iron reduction and diopside-based glass ceramic preparation based on mineral carbonation of steel slag

In this article, a new process for treating steel slag and CO₂ simultaneously and preparing calcium carbonate, metallic iron, and glass ceramics without wastewater or gas production is proposed. The reduction of iron and preparation of diopside glass ceramics are studied in this paper, and the results show that the carbon thermal reduction product of the original slag does not reach its melting point, and the slag and iron are well separated in the samples containing the leached steel slag and added silica. Part of the parent glass is converted into a glass ceramic after heat treatment, and the crystalline phases of samples are melilite, diopside, and partial melilite, and diopside and anorthite, respectively. The crystallization activation energy of the best sample in this article is E = 660.664 kJ/mol. The Avrami indices calculated at different heating rates are all less than 3, which indicates that the crystallization mode of the glass involves surface crystallization. This finding is consistent with the results for the prepared glass ceramics.

Heavy metal removal from water by adsorption using a low-cost geopolymer

In the present study, a geopolymer from dolochar ash was synthesized and used for the removal of heavy metal ions such as Co(II), Ni(II), Cd(II), and Pb(II) from the aqueous solution through the adsorption process. The geopolymer was characterized by a series of analytical techniques. The XRD pattern revealed the loss of dolochar ash crystallinity on geoploymerization. The peak at 982 cm^-1 observed in the FTIR spectrum due to Si-O-Si and Si-O-Al bonds confirmed the formation of geopolymer. BET surface area analyses indicated the mesoporous nature of the sample. The adsorption experiments revealed the higher removal efficiency of the geopolymer in comparison with the feed dolochar ash. The effects of different experimental factors such as pH, temperature, reaction time, and initial concentration of metal ions on metal uptake efficiency were evaluated to optimize the removal efficiency. The maximum removal of 98-99% was achieved when the pH, temperature, and initial metal ion concentration were 7.8, 343 K, and 10 ppm, respectively. The adsorption process followed the pseudo-second-order rate equation and validated the Langmuir adsorption model. Thermodynamic parameters such as ΔH, ΔS, and ΔG confirmed that the process to be spontaneous and endothermic. This geopolymer was found to compete efficiently with many adsorbents reported in the literature for water treatment.