A simple magnetic solid-phase extraction method based on magnetite/graphene oxide nanocomposite for pre-concentration and determination of melamine by high-performance liquid chromatography

An air-assisted dispersive liquid phase microextraction method based on a hydrophobic magnetic deep eutectic solvent for the extraction and preconcentration of melamine from milk and milk-based products

In the current research, a fast and sustainable air-assisted hydrophobic magnetic deep eutectic solvent-based dispersive liquid phase microextraction followed by UV-Vis spectrophotometry measurements was optimized for the extraction and determination of melamine in milk and milk-based products. The central composite design was applied for the optimization of factors affecting the recovery of melamine. Quantitative extraction of melamine was achieved using hydrophobic magnetic deep eutectic solvents prepared from a mixture of octanoic acid, aliquat-336, and cobalt(II) chloride. The optimum conditions for extraction were found as follows: 6 extraction cycles, pH 8.2, extraction solvent volume 260 µL, and acetone volume 125 µL.Interestingly, a centrifugation step was not required to achieve phase separation. Under the optimum conditions, melamine was determined in the linear range of 3-600 ng mL^-1, the limit of detection (3S_blank/m) of 0.9 ng mL^-1, and the enrichment factor of 144. The validation of the method was investigated by the analysis of reference materials. Consequently, the method was successfully applied for the analysis of melamine residues in milk and milk-based products.

Melamine in Iranian foodstuffs: A systematic review, meta-analysis, and health risk assessment of infant formula

The presence of melamine in food is one of the most significant threats to consumer health and food safety now confronting the communities. The goal of this systematic review and meta-analysis was to determine the melamine content of different food products available on the Iranian market. The pooled melamine concentration (95% confidence interval) on 484 samples of animal-based foodstuffs was as follows: 0.22 (0.08, 0.36 mg kg^-1) for milk, 0.39 (0.25, 0.53 mg kg^-1) for coffee mate, 1.45 (1.36, 1.54 mg kg^-1) for dairy cream, 0.90 (0.50, 1.29 mg kg^-1) for yoghurt, 1.25 (1.20, 1.29 mg kg^-1) for cheese, 0.81 (-0.16, 1.78 mg kg^-1) for hen eggs, 1.28 (1.25, 1.31 mg kg^-1) for poultry meat, 0.58 (0.35, 0.80 mg kg^-1) for chocolates, and 0.98 (0.18, 1.78 mg kg^-1) for infant formula. Based on the results of health risk assessment study on toddlers under 2 years old who ingested infant formula (as a melamine-sensitive group), all groups of toddlers are at an acceptable level of non-carcinogenic risk (THQ ≤ 1). Toddlers were classified according to their ILCR (carcinogenic risk) levels due to infant formula consumption as follows: under 6 months (0.0000056), 6-12 months (0.0000077), 12-18 months (0.0000102), and 18-24 months (0.0000117). The melamine carcinogenicity in infant formula for children had an ILCR value of 0.000001-0.0001 in the investigation, which was considerable risk. According to the findings, Iranian food products (notably infant formula) should be analyzed for melamine contamination on a regular basis.

Magnetic solid-phase extraction based on GO/Fe3O4 coupled with UPLC-MS/MS for determining nitroimidazoles and their metabolites in honey

A magnetic graphene oxide (GO/Fe₃O₄) nanocomposite was synthesized in one step by a chemical coprecipitation method, which was further used for magnetic solid-phase extraction (MSPE). This study aimed to combine GO/Fe₃O₄ with ultra-high-performance liquid chromatography-tandem mass spectrometry (UPLC-MS/MS) to detect the nitroimidazoles (NDZs) and their three major metabolites in honey samples. GO/Fe₃O₄ was characterized by transmission electron microscopy (TEM), Fourier transform-infrared (FT-IR) spectroscopy, and magnetic property measurement system (MPMS), and the influencing parameters such as adsorbent amount, pH of the dissolved sample solution, sample volume, type and volume of the eluent, shaking speed, and adsorption and desorption time were optimized. Under the optimized conditions, the limits of detection (LOD) and quantitation (LOQ) of the method were 0.003-0.08 μg kg^-1 and 0.009-0.3 μg kg^-1, respectively, with good linearity reported in the range of 0.5-20 μg kg^-1 (R² ≥ 0.9991). The average recoveries of 10 analytes were in the range of 66.0%-90.8% with relative standard deviations (RSD) lower than 6.9% (n = 6). The preparation of GO/Fe₃O₄ and the extraction process were convenient and rapid, and consumed small amounts of organic solvents. The optimized method was successfully applied for extracting NDZs and their three major metabolites from honey samples with good accuracy.

Simultaneous removal of Cu (II) and Cr (VI) ions from petroleum refinery wastewater using ZnO/Fe3O4 nanocomposite

The presence and removal of heavy metals such as Cu(II) as well as Cr(VI) in petroleum refinery wastewater calls for concerted efforts due to their mobility, toxicity, bioaccumulation, and non-biodegradability in the environment. In this present work, zinc oxide (ZnO), iron oxide (Fe₃O₄) nanoparticles and ZnO/Fe₃O₄ nanocomposites were synthesized via simple sol-gel and chemical reduction methods; characterized using different analytical tools and then applied as nanoadsorbent to sequester Cu(II) and Cr(VI) ions from Petroleum Refinery wastewater via batch adsorption process. Cu(II) and Cr(VI) adsorption processes were examined with respect to contact time (kinetic effect), nanoadsorbent dosage, isotherm equilibrium, and thermodynamic parameters. ZnO/Fe₃O₄ nanocomposites with higher surface area (39.450 m²/g) have a mixture of rod-like and spherical shapes as compared to ZnO and Fe₃O₄ nanoparticles with spherical shape only and surface areas of 8.62 m²/g and 7.86 m²/g) according to the high-resolution scanning electron microscopy (HRSEM) and Brunauer-Emmett-Teller (BET) analysis. The X-ray diffractometer (XRD) results revealed the formation of hexagonal wurtzite structure of ZnO and the face-centered cubic structure phase of Fe₃O₄ nanoparticles, after the formation of the ZnO/Fe₃O₄ nanocomposites the phases of the nanoparticles were not affected but the diffraction peaks shifted to higher 2θ degree. The average crystallite size of ZnO and Fe₃O₄ nanoparticles and ZnO/Fe₃O₄ nanocomposites were 20.12, 26.36 and 14.50 nm respectively. The maximum removal efficiency of Cu (II) (92.99%) and Cr (VI) (77.60%) by ZnO/Fe₃O₄ nanocomposites was higher than 85.83%; 65.19% for Cu (II) and 80.57%; 62.53 for Cr (VI) using ZnO and Fe₃O₄ nanoadsorbents individually under the following conditions: contact time (15), dosage (0.08 g) and temperature (30 °C). The experimental data for Cu (II) and Cr (VI) ion removal fitted well to the pseudo-second-order kinetic and Langmuir isotherm models. The thermodynamic study suggested that the removal of the two metal ions from petroleum wastewater was endothermic. The reusability study after the fourth adsorption-desorption cycle indicated the stability of ZnO/Fe₃O₄ nanocomposites with 85.51% and 69.42% removal efficiency of Cu (II) and Cr (VI). The results showed that ZnO/Fe₃O₄ nanocomposite achieves higher performance than ZnO and Fe₃O₄ alone in the removal of Cu (II) and Cr (VI) ions from the petroleum refinery wastewater.

[Research progress in the application of magnetic solid phase extraction based on carbon based magnetic materials in food analysis]

Trace toxic substances in food pose a serious threat to human health, and need to be detected and analyzed to ensure food safety. However, there are many kinds of toxic substances in food, with small amounts and complex matrices, making it necessary to select an appropriate sample pretreatment technology for extraction and purification. There are some disadvantages to sample pretreatment methods such as solid phase extraction and liquid-liquid extraction, in terms of poor selectivity, significant influence of matrix interference, large sample requirement, long extraction time, use of a large amount of harmful organic solvents, and cumbersome and time-consuming operation. Magnetic solid phase extraction (MSPE) combines the advantages of magnetic separation and traditional SPE technology, avoids time-consuming column loading, and can extract the target analyte efficiently. Because of its advantages, in that it has simple operation, is time-saving and fast, requires no centrifugal filtration, and is environmentally friendly, it is considered an efficient sample pretreatment technology and applied in food analysis. The adsorption capacity and selectivity of the magnetic adsorbent used in MSPE are the key factors affecting the extraction efficiency and selectivity of MSPE, and play a key role in the accuracy of the established method. Carbon-based magnetic materials are a type of new functional magnetic materials prepared by the co-precipitation of carbon-based materials (carbon nanotubes, graphene, metal-organic framework-derived carbon, or activated carbon) and magnetic materials. In order to endow carbon-based magnetic materials with the advantages of both, carbon materials and magnetic materials, while also reflecting the advantages of high specific surface area, good stability, low cost, environmental friendliness, excellent physical and chemical properties, high porosity, and high adsorption capacity, proper functional modification is needed. Carbon-based magnetic materials modified by functionalization can efficiently enrich organic and inorganic analytes with different properties, and have seen significant progress in environmental analysis, biological detection, pollution control, and other fields. In recent years, MSPE technology based on carbon-based magnetic materials has been gradually applied in food analysis and pretreatment, but its use is still in infancy and holds immense application potential. Reference to more than 50 papers published in SCI and Chinese core journals over the past four years reveals that carbon-based materials include carbon nanotubes modified by functional groups, reagents, or materials; graphene, graphene oxide, and reduced graphene oxide; carbon derived from a gold organic framework; activated carbon biochar; and nanodiamond. The harmful substances in food samples include esters, mycotoxins, polycyclic aromatic hydrocarbons, antibiotics, alkaloids, phenols, vitamins, and antibiotics. Based on the classification of carbon-based materials, this review reveals that carbon-based magnetic materials have good preconcentration ability for harmful substances in food samples. MSPE can be combined with GC-MS, liquid chromatography-high resolution mass spectrometry (LC-HRMS), ultra-fast liquid chromatography-tandem mass spectrometry (UFLC-MS/MS), ultra high performance liquid chromatography-Q-Exactive high resolution mass spectrometry (UHPLC-Q-Exactive HRMS), high performance liquid chromatography-diode array detection (HPLC-DAD), gas chromatography micro-electron capture detection (GC-μECD), high performance liquid chromatography fluorescence with post-column photochemical derivatization (HPLC-PCD-FLD), and HPLC-UV to analyze food samples. These combined technologies have high accuracy and recovery. However, the synthesis methods of carbon-based magnetic materials such as carbon nanotubes and graphene, incur high energy consumption and high cost, and involve complex processes, which limit their application. Therefore, a carbon-based magnetic adsorbent with low cost, high selectivity, and high extraction efficiency was developed by further exploring functional modification with biochar as a carbon base. This is a very promising direction to develop MSPE technology utilizing biochar-based magnetic materials for food sample pretreatment. This review provides a theoretical basis and technical support for the wide application of carbon-based magnetic materials in MSPE technology for food analysis.

Application of magnetic nanomaterials in bioanalysis

The importance of magnetic nanomaterials and magnetic hybrid materials, which are classified as new generation materials, in analytical applications is increasingly understood, and research on the adaptation of these materials to analytical methods has gained momentum. Development of sample preparation techniques and sensor systems using magnetic nanomaterials for the analysis of inorganic, organic and biomolecules in biological samples, which are among the samples that analytical chemists work on most, are among the priority issues. Therefore in this review, we focused on the use of magnetic nanomaterials for the bioanalytical applications including inorganic and organic species and biomolecules in different biological samples such as primarily blood, serum, plasma, tissue extracts, urine and milk. We summarized recent progresses, prevailing techniques, applied formats, and future trends in sample preparation-analysis methods and sensors based on magnetic nanomaterials (Mag-NMs). First, we provided a brief introduction of magnetic nanomaterials, especially their magnetic properties that can be utilized for bioanalytical applications. Second, we discussed the synthesis of these Mag-NMs. Third, we reviewed recent advances in bioanalytical applications of the Mag-NMs in different formats. Finally, recently literature studies on the relevance of Mag-NMs for bioanalysis applications were presented.

Sonodecoration of magnetic phosphonated-functionalized sporopollenin as a novel green nanocomposite for stir bar sorptive dispersive microextraction of melamine in milk and milk-based food products

The novel green magnetic phosphonated-functionalized sporopollenin nanocomposite (MPSP-nanocomposite) was synthetized and used for stir bar sorptive dispersive microextraction (SBSDME) of melamine in milk and milk-based food products. TEM, SEM-EDX, FT-IR, VSM techniques were applied for characterization of MPSP-nanocomposite. The influential parameters including pH, extraction time, stirring rate, elution solvent type and volume, sample volume, desorption time, and ionic strength were studied and at optimum conditions, the linear range of 1-500 (µg L^-1), the LOD (S/N = 3) of 0.30 (µg L^-1), and the LOQ (S/N = 10) of 0.95 (µg L^-1) were achieved. The intra-day precision values (RSD (%), n = 7) of 3.5% for the melamine concentration of 25 (µg L^-1). The relative recoveries of 95.8% to 99.6% were acquired for the real samples which confirmed that the proposed method could be successfully utilized in complex matrixes with high matrix effects.

The Current Role of Graphene-Based Nanomaterials in the Sample Preparation Arena

Since its discovery in 2004 by Novoselov et al., graphene has attracted increasing attention in the scientific community due to its excellent physical and chemical properties, such as thermal/mechanical resistance, electronic stability, high Young's modulus, and fast mobility of charged atoms. In addition, other remarkable characteristics support its use in analytical chemistry, especially as sorbent. For these reasons, graphene-based materials (GBMs) have been used as a promising material in sample preparation. Graphene and graphene oxide, owing to their excellent physical and chemical properties as a large surface area, good mechanical strength, thermal stability, and delocalized π-electrons, are ideal sorbents, especially for molecules containing aromatic rings. They have been used in several sample preparation techniques such as solid-phase extraction (SPE), stir bar sorptive extraction (SBSE), magnetic solid-phase extraction (MSPE), as well as in miniaturized modes as solid-phase microextraction (SPME) in their different configurations. However, the reduced size and weight of graphene sheets can limit their use since they commonly aggregate to each other, causing clogging in high-pressure extractive devices. One way to overcome it and other drawbacks consists of covalently attaching the graphene sheets to support materials (e.g., silica, polymers, and magnetically modified supports). Also, graphene-based materials can be further chemically modified to favor some interactions with specific analytes, resulting in more efficient hybrid sorbents with higher selectivity for specific chemical classes. As a result of this wide variety of graphene-based sorbents, several studies have shown the current potential of applying GBMs in different fields such as food, biological, pharmaceutical, and environmental applications. Within such a context, this review will focus on the last five years of achievements in graphene-based materials for sample preparation techniques highlighting their synthesis, chemical structure, and potential application for the extraction of target analytes in different complex matrices.