From first generation biofuels to advanced solar biofuels

Methanol as a co-substrate with CO2 enhances butyrate production in microbial electrosynthesis

Methanol is a promising feedstock for the bio-based economy as it can be derived from organic waste streams or produced electrochemically from CO2. Acetate production from CO2 in microbial electrosynthesis (MES) has been widely studied, while more valuable compounds such as butyrate are currently attracting attention. In this study, methanol was used as a co-substrate with CO2 to enhance butyrate production in MES. Feeding with CO2 and methanol resulted in the highest butyrate production rates and titres of 0.36 ± 0.01 g L-1 d-1 and 8.6 ± 0.2 g L-1, respectively, outperforming reactors with only CO2 feeding (0.20 ± 0.03 g L-1 d-1 and 5.2 ± 0.1 g L-1, respectively). Methanol acted as electron donor and as carbon source, both of which contributed ca. 50% of the carbon in the products. Eubacterium was the dominant genus with 52.6 ± 2.5% relative abundance. Thus, we demonstrate attractive route for the use of the C1 substrates, CO2 and methanol, to produce mainly butyrate. KEY POINTS: • Butyrate was the main product from methanol and CO2 in MES • Methanol acted as both carbon and electron source in MES • Eubacterium dominating microbial culture was enriched in MES.

Renewable Energy Potential: Second-Generation Biomass as Feedstock for Bioethanol Production

Biofuels are clean and renewable energy resources gaining increased attention as a potential replacement for non-renewable petroleum-based fuels. They are derived from biomass that could either be animal-based or belong to any of the three generations of plant biomass (agricultural crops, lignocellulosic materials, or algae). Over 130 studies including experimental research, case studies, literature reviews, and website publications related to bioethanol production were evaluated; different methods and techniques have been tested by scientists and researchers in this field, and the most optimal conditions have been adopted for the generation of biofuels from biomass. This has ultimately led to a subsequent scale-up of procedures and the establishment of pilot, demo, and large-scale plants/biorefineries in some regions of the world. Nevertheless, there are still challenges associated with the production of bioethanol from lignocellulosic biomass, such as recalcitrance of the cell wall, multiple pretreatment steps, prolonged hydrolysis time, degradation product formation, cost, etc., which have impeded the implementation of its large-scale production, which needs to be addressed. This review gives an overview of biomass and bioenergy, the structure and composition of lignocellulosic biomass, biofuel classification, bioethanol as an energy source, bioethanol production processes, different pretreatment and hydrolysis techniques, inhibitory product formation, fermentation strategies/process, the microorganisms used for fermentation, distillation, legislation in support of advanced biofuel, and industrial projects on advanced bioethanol. The ultimate objective is still to find the best conditions and technology possible to sustainably and inexpensively produce a high bioethanol yield.

High potential for biomass-degrading CAZymes revealed by pine forest soil metagenomics

The undisturbed environment in Netarhat, with its high levels of accumulated lignocellulosic biomass, presents an opportunity to identify microbes for biomass digestion. This study focuses on the bioprospecting of native soil microbes from the Netarhat forest in Jharkhand, India, with the potential for lignocellulosic substrate digestion. These biocatalysts could help overcome the bottleneck of biomass saccharification and reduce the overall cost of biofuel production, replacing harmful fossil fuels. The study used metagenomic analysis of pine forest soil via whole genome shotgun sequencing, revealing that most of the reads matched with the bacterial species, very low percentage of reads (0.1%) belongs to fungal species, with 13% of unclassified reads. Actinobacteria were found to be predominant among the bacterial species. MetaErg annotation identified 11,830 protein family genes and 2 metabolic marker genes in the soil samples. Based on the Carbohydrate Active EnZyme (CAZy) database, 3,996 carbohydrate enzyme families were identified, with family Glycosyl hydrolase (GH) dominating with 1,704 genes. Most observed GH families in the study were GH0, 3, 5, 6. 9, 12. 13, 15, 16, 39, 43, 57, and 97. Modelling analysis of a representative GH 43 gene suggested a strong affinity for cellulose than xylan. This study highlights the lignocellulosic digestion potential of the native microfauna of the lesser-known pine forest of Netarhat.Communicated by Ramaswamy H. Sarma.

Comparison of the effects of nitrogen-, sulfur- and combined nitrogen- and sulfur-deprivations on cell growth, lipid bodies and gene expressions in Chlamydomonas reinhardtii cc5373-sta6

BACKGROUND

Biofuel research that aims to optimize growth conditions in microalgae is critically important. Chlamydomonas reinhardtii is a green microalga that offers advantages for biofuel production research. This study compares the effects of nitrogen-, sulfur-, and nitrogen and sulfur- deprivations on the C. reinhardtii starchless mutant cc5373-sta6. Specifically, it compares growth, lipid body accumulation, and expression levels of acetyl-CoA carboxylase (ACC) and phosphoenolpyruvate carboxylase (PEPC).

RESULTS

Among nutrient-deprived cells, TAP-S cells showed significantly higher total chlorophyll, cell density, and protein content at day 6 (p < 0.05). Confocal analysis showed a significantly higher number of lipid bodies in cells subjected to nutrient deprivation than in the control over the course of six days; N deprivation for six days significantly increased the size of lipid bodies (p < 0.01). In comparison with the control, significantly higher ACC expression was observed after 8 and 24 h of NS deprivation and only after 24 h with N deprivation. On the other hand, ACC and PEPC expression at 8 and 24 h of S deprivation was not significantly different from that in the control. A significantly lower PEPC expression was observed after 8 h of N and NS deprivation (p < 0.01), but a significantly higher PEPC expression was observed after 24 h (p < 0.01).

CONCLUSIONS

Based on our findings, it would be optimum to cultivate cc5373-sta6 cells in nutrient deprived conditions (-N, -S or -NS) for four days; whereby there is cell growth, and both a high number of lipid bodies and a larger size of lipid bodies produced.

Effects of Saccharomyces cerevisiae quorum sensing signal molecules on ethanol production in bioethanol fermentation process

In this study, the concentrations of Saccharomyces cerevisiae quorum sensing signal molecules (QSMs) were determined, not to mention the exploration of the effects of exogenous S. cerevisiae QSMs on the sole fermentation of S. cerevisiae and co-fermentation of S. cerevisiae and Lactobacillus plantarum. The results showed that the concentrations of three signal molecules (2-phenylethanol (2-PE), tyrosol and tryptophan) produced by S. cerevisiae increased with a higher bacteria density, which tends to become stable up to 118.02, 32.05 and 1.93 mg/L respectively when cultivating for 144 h. Among the three signaling molecules, only 2-PE promoted the ethanol production capacity of S. cerevisiae. The ethanol concentration of the sole fermentation of S. cerevisiae loaded with 120 mg/L 2-PE reached 3.2 g/L in 9 h, which was 58.7% higher than that of the group without 2-PE addition. Moreover, 2-PE reduced the negative impact of L. plantarum on S. cerevisiae. Within 12 h of the co-fermentation of L. plantarum and S. cerevisiae, the ethanol concentration in the co-fermentation group loaded with 2-PE reached 5.6 g/L, similar to that in the group fermenting with sole S. cerevisiae, and the yeast budding rate was also restored to 28.51%. qRT-PCR results of S. cerevisiae which was in sole fermentation with 2-PE addition for 9 h showed that the relative expression levels of ethanol dehydrogenase gene ADH1 in S. cerevisiae decreased by 25% and the relative expression levels of MLS1, CIT2, IDH1,CIT1 decreased by 26%, 30%, 22%,18%, respectively, meant that the glyoxylic and tricarboxylic acid cycles were greatly inhibited, which promotes the accumulation of ethanol. The results of this study provide basic data for using QSMs more than antibiotics in the the prevention of contamination during the industrialized bioethanol production.

The potential of biofuels from first to fourth generation

The steady increase in human population and a rising standard of living heighten global demand for energy. Fossil fuels account for more than three-quarters of energy production, releasing enormous amounts of carbon dioxide (CO2) that drive climate change effects as well as contributing to severe air pollution in many countries. Hence, drastic reduction of CO2 emissions, especially from fossil fuels, is essential to tackle anthropogenic climate change. To reduce CO2 emissions and to cope with the ever-growing demand for energy, it is essential to develop renewable energy sources, of which biofuels will form an important contribution. In this Essay, liquid biofuels from first to fourth generation are discussed in detail alongside their industrial development and policy implications, with a focus on the transport sector as a complementary solution to other environmentally friendly technologies, such as electric cars.

Increasing Sugar Content in Source for Biofuel Production Using Agrochemical and Genetic Approaches at the Stages of BioMass Preharvesting and Harvesting

In order to optimize biofuel (including bioethanol) production processes, various problems need to be solved, such as increasing the sugar content of raw materials/biomass to gain a higher yield of the product. This task can be solved in several ways, with their own advantages and disadvantages, and an integrated approach, such as using a combination of ripening agents and phytohormones or application of a superabsorbent polymer with at least one sugar-enhancing agent, can be applied as well. Here, we reviewed several methods, including pre- and postharvest factors (light, temperature, partial replacement of potassium with magnesium, etc.), genetic modifications (traditional breeding, phytohormones, etc.), chemical ripening methods (Ethephon, Moddus, etc.), and some alternative methods (DMSO treatment, ionic liquids, etc.). The aim of this review was to provide a comprehensive, up-to-date summary of methods of increasing the carbohydrate level in plants/biomass for bioethanol production.

Patterning of the Autotrophic, Mixotrophic, and Heterotrophic Proteomes of Oxygen-Evolving Cyanobacterium Synechocystis sp. PCC 6803

Proteomes of an oxygenic photosynthetic cyanobacterium, Synechocystis sp. PCC 6803, were analyzed under photoautotrophic (low and high CO₂, assigned as ATLC and ATHC), photomixotrophic (MT), and light-activated heterotrophic (LAH) conditions. Allocation of proteome mass fraction to seven sub-proteomes and differential expression of individual proteins were analyzed, paying particular attention to photosynthesis and carbon metabolism–centered sub-proteomes affected by the quality and quantity of the carbon source and light regime upon growth. A distinct common feature of the ATHC, MT, and LAH cultures was low abundance of inducible carbon-concentrating mechanisms and photorespiration-related enzymes, independent of the inorganic or organic carbon source. On the other hand, these cells accumulated a respiratory NAD(P)H dehydrogenase I (NDH-1₁) complex in the thylakoid membrane (TM). Additionally, in glucose-supplemented cultures, a distinct NDH-2 protein, NdbA, accumulated in the TM, while the plasma membrane-localized NdbC and terminal oxidase decreased in abundance in comparison to both AT conditions. Photosynthetic complexes were uniquely depleted under the LAH condition but accumulated under the ATHC condition. The MT proteome displayed several heterotrophic features typical of the LAH proteome, particularly including the high abundance of ribosome as well as amino acid and protein biosynthesis machinery-related components. It is also noteworthy that the two equally light-exposed ATHC and MT cultures allocated similar mass fractions of the total proteome to the seven distinct sub-proteomes. Unique trophic condition-specific expression patterns were likewise observed among individual proteins, including the accumulation of phosphate transporters and polyphosphate polymers storing energy surplus in highly energetic bonds under the MT condition and accumulation under the LAH condition of an enzyme catalyzing cyanophycin biosynthesis. It is concluded that the rigor of cell growth in the MT condition results, to a great extent, by combining photosynthetic activity with high intracellular inorganic carbon conditions created upon glucose breakdown and release of CO₂, besides the direct utilization of glucose-derived carbon skeletons for growth. This combination provides the MT cultures with excellent conditions for growth that often exceeds that of mere ATHC.

Heterologous Lactate Synthesis in Synechocystis sp. Strain PCC 6803 Causes a Growth Condition-Dependent Carbon Sink Effect

Cyanobacteria are considered promising hosts for product synthesis directly from CO₂ via photosynthetic carbon assimilation. The introduction of heterologous carbon sinks in terms of product synthesis has been reported to induce the so-called “carbon sink effect,” described as the release of unused photosynthetic capacity by the introduction of additional carbon. This effect is thought to arise from a limitation of carbon metabolism that represents a bottleneck in carbon and electron flow, thus enforcing a downregulation of photosynthetic efficiency. It is not known so far how the cellular source/sink balance under different growth conditions influences the extent of the carbon sink effect and in turn product formation from CO₂, constituting a heterologous carbon sink. We compared the Synechocystis sp. strain PCC 6803 wild type (WT) with an engineered lactate-producing strain (SAA023) in defined metabolic states. Unexpectedly, high-light conditions combined with carbon limitation enabled additional carbon assimilation for lactate production without affecting biomass formation. Thus, a strong carbon sink effect only was observed under carbon and thus sink limitation, but not under high-sink conditions. We show that the carbon sink effect was accompanied by an increased rate of alternative electron flow (AEF). Thus, AEF plays a crucial role in the equilibration of source/sink imbalances, presumably via ATP/NADPH balancing. This study emphasizes that the evaluation of the biotechnological potential of cyanobacteria profits from cultivation approaches enabling the establishment of defined metabolic states and respective quantitative analytics. Factors stimulating photosynthesis and carbon fixation are discussed.

IMPORTANCE Previous studies reported various and differing effects of the heterologous production of carbon-based molecules on photosynthetic and growth efficiency of cyanobacteria. The typically applied cultivation in batch mode, with continuously changing growth conditions, however, precludes a clear differentiation between the impact of cultivation conditions on cell physiology and effects related to the specific nature of the product and its synthesis pathway. In this study, we employed a continuous cultivation system to maintain defined source/sink conditions and thus metabolic states. This allowed a systematic and quantitative analysis of the effect of NADPH-consuming lactate production on photosynthetic and growth efficiency. This approach enables a realistic evaluation of the biotechnological potential of engineered cyanobacterial strains. For example, the quantum requirement for carbon production was found to constitute an excellent indicator of the source/sink balance and thus a key parameter for photobioprocess optimization. Such knowledge is fundamental for rational and efficient strain and process development.

Recent Developments in Lignocellulosic Biofuels, a Renewable Source of Bioenergy

Biofuel consists of non-fossil fuel derived from the organic biomass of renewable resources, including plants, animals, microorganisms, and waste. Energy derived from biofuel is known as bioenergy. The reserve of fossil fuels is now limited and continuing to decrease, while at the same time demand for energy is increasing. In order to overcome this scarcity, it is vital for human beings to transfer their dependency on fossil fuels to alternative types of fuel, including biofuels, which are effective methods of fulfilling present and future demands. The current review therefore focusses on second-generation lignocellulosic biofuels obtained from non-edible plant biomass (i.e., cellulose, lignin, hemi-celluloses, non-food material) in a more sustainable manner. The conversion of lignocellulosic feedstock is an important step during biofuel production. It is, however, important to note that, as a result of various technical restrictions, biofuel production is not presently cost efficient, thus leading to the need for improvement in the methods employed. There remain a number of challenges for the process of biofuel production, including cost effectiveness and the limitations of various technologies employed. This leads to a vital need for ongoing and enhanced research and development, to ensure market level availability of lignocellulosic biofuel.

Diatoms as a biotechnological resource for the sustainable biofuel production: a state-of-the-art review

The greenhouse gas emission from fossil fuel and higher economic cost in its transportation are stimulating scientists to explore biomass energy production at the local level. In the present review, the authors have explored the prospects of commercial-scale biofuels production from the microalgal group, diatoms. Insights on suitability of mass cultivation systems for large-scale production of diatoms have been deliberated based on published literature. Diatoms can proliferate extracting nutrients from the wastewater and the same biomass can be harvested for biofuel production. Residues can be further utilized for the formation of other bioproducts and biofertilizers. The residual applications of diatoms from mass culture are estimated to compensate for the additional costs incurred in the removal of impurities. Well-planned research is required to optimize the commercial-scale production of biofuels from diatoms. The aim of this review is therefore, to demonstrate the economically feasible, hygienically safe cultivation of diatoms on nutrients from wastewater, limitations in using diatoms for biofuel production, and how these limitations can be shorted out for optimum utilization of diatom for biofuel production.

Computational Modeling Approaches of Hydrothermal Carbonization: A Critical Review

Hydrothermal carbonization (HTC) continues to gain recognition over other valorization techniques for organic and biomass residue in recent research. The hydrochar product of HTC can be effectively produced from various sustainable resources and has been shown to have impressive potential for a wide range of applications. As industries work to adapt the implementation of HTC over large processes, the need for reliable models that can be referred to for predictions and optimization studies are becoming imperative. Although much of the available research relating to HTC has worked on the modeling area, a large gap remains in developing advanced computational models that can better describe the complex mechanisms, heat transfer, and fluid dynamics that take place in the reactor of the process. This review aims to highlight the importance of expanding the research relating to computational modeling for HTC conversion of biomass. It identifies six research areas that are recommended to be further examined for contributing to necessary advancements that need to be made for large-scale and continuous HTC operations. The six areas that are identified for further investigation are variable feedstock compositions, heat of exothermic reactions, type of reactor and scale-up, consideration of pre-pressurization, consideration of the heat-up period, and porosity of feedstock. Addressing these areas in future HTC modeling efforts will greatly help with commercialization of this promising technology.

Changes in the Structure of Crop Production in Slovakia after 2004 Using an Example of Selected Crops

Spatial changes in the structure of crop production have the potential to impact economics and food security in Slovakia. The objective of this study was to analyze the modification of harvested areas, the production and yields of selected crops—cereals, oilseeds, and perennial forages—and their food and non-food use from 2004 to 2020. The results indicated that an increase in the cultivation of large-scale crops (cereals and oilseeds) has occurred at the expense of crops produced for food. Changes in the structure of plant production indicate negative risk factor that reduce the competitiveness of the agricultural sector and threaten Slovakia’s food security. Moran’s global and Moran’s local autocorrelation index were used in the synthesis of the findings. A spatial autocorrelation analysis of the harvest areas of selected crops was used as a practical approach to locate statistically significant areas with high or low crop harvest. This manifested itself as positive spatial autocorrelation.

n-Butanol production by Rhodopseudomonas palustris TIE-1

Anthropogenic carbon dioxide (CO₂) release in the atmosphere from fossil fuel combustion has inspired scientists to study CO₂ to biofuel conversion. Oxygenic phototrophs such as cyanobacteria have been used to produce biofuels using CO₂. However, oxygen generation during oxygenic photosynthesis adversely affects biofuel production efficiency. To produce n-butanol (biofuel) from CO₂, here we introduce an n-butanol biosynthesis pathway into an anoxygenic (non-oxygen evolving) photoautotroph, Rhodopseudomonas palustris TIE-1 (TIE-1). Using different carbon, nitrogen, and electron sources, we achieve n-butanol production in wild-type TIE-1 and mutants lacking electron-consuming (nitrogen-fixing) or acetyl-CoA-consuming (polyhydroxybutyrate and glycogen synthesis) pathways. The mutant lacking the nitrogen-fixing pathway produce the highest n-butanol. Coupled with novel hybrid bioelectrochemical platforms, this mutant produces n-butanol using CO₂, solar panel-generated electricity, and light with high electrical energy conversion efficiency. Overall, this approach showcases TIE-1 as an attractive microbial chassis for carbon-neutral n-butanol bioproduction using sustainable, renewable, and abundant resources.

Net Energy Analysis and Techno-Economic Assessment of Co-Production of Bioethanol and Biogas from Cellulosic Biomass

Co-production is a process based on the biorefinery concept that maximizes the benefit of biomass by reusing residue from the production of one product to produce others. In this regard, biogas is one of the most researched second products for the production of ethanol from cellulosic biomass. However, operating this scheme requires additional investment in biogas processing equipment. This review compiles data from research studies on the co-production of bioethanol and biogas from lignocellulosic biomass to determine which is more worthwhile: leaving the residue or investing more to benefit from the second product. According to previous research, ethanol stillage can be converted to biogas via anaerobic digestion, increasing energy output by 2–3 fold. Techno-economic studies demonstrated that the co-production process reduces the minimum ethanol selling price to a level close to the market price of ethanol, implying the possibility of industrializing cellulosic ethanol production through this scheme.

Investigation of Biofuel as a Potential Renewable Energy Source

An accelerating global energy demand, paired with the harmful environmental effects of fossil fuels, has triggered the search for alternative, renewable energy sources. Biofuels are arguably a potential renewable energy source in the transportation industry as they can be used within current infrastructures and require less technological advances than other renewable alternatives, such as electric vehicles and nuclear power. The literature suggests biofuels can negatively impact food security and production; however, this is dependent on the type of feedstock used in biofuel production. Advanced biofuels, derived from inedible biomass, are heavily favoured but require further research and development to reach their full commercial potential. Replacing fossil fuels by biofuels can substantially reduce particulate matter (PM), carbon monoxide (CO) emissions, but simultaneously increase emissions of nitrogen oxides (NOx), acetaldehyde (CH3CHO) and peroxyacetyl nitrate (PAN), resulting in debates concerning the way biofuels should be implemented. The potential biofuel blends (FT-SPK, HEFA-SPK, ATJ-SPK and HFS-SIP) and their use as an alternative to kerosene-type fuels in the aviation industry have also been assessed. Although these fuels are currently more costly than conventional aviation fuels, possible reduction in production costs has been reported as a potential solution. A preliminary study shows that i-butanol emissions (1.8 Tg/year) as a biofuel can increase ozone levels by up to 6% in the upper troposphere, highlighting a potential climate impact. However, a larger number of studies will be needed to assess the practicalities and associated cost of using the biofuel in existing vehicles, particularly in terms of identifying any modifications to existing engine infrastructure, the impact of biofuel emissions, and their chemistry on the climate and human health, to fully determine their suitability as a potential renewable energy source.

A Comprehensive Review on Biofuels from Oil Palm Empty Bunch (EFB): Current Status, Potential, Barriers and Way Forward

Biomass is an important renewable energy resource which primarily contributes to heating and cooling end use sectors. It is also a promising alternative source of biofuels to replace the depleting supply of fossil fuels. Surprisingly, few writers have been able to draw on the feedstock significance for oil palm empty fruit bunch (EFB) as the biomass resource for biofuels compared to the other types of biomass waste. Therefore, this paper presents a comprehensive review of EFB as a biomass resource presented in four major parts. First, the introduction covers the demand for bio-oil and describes the different kinds of feedstock, the relevance and potential of EFB biomass. Second, the characteristics of biomass are explained before it is upgraded as biofuel, drawing similarities and contrasts between EFB and other sources of biomass. Pyrolysis processes and reactors used for EFB conversion are described, and the factors affecting the bio-oil yield and quality are discussed. Major reactor parameters are summarized and reactor optimization is discussed. Third, comparison on the properties of the bio-oil vs. petroleum in transportation, power generation, and heating are compared followed by prioritizing the bio-oil properties from the most to least critical, revealing the most promising methods for upgrading. Fourth, the environmental impact, including CO2 emission, of the use of EFB as a promising renewable energy resource and a cleaner alternative fuel is recommended. This paper has comprehensively reviewed the conversion of oil palm empty fruit bunches into biofuels, including the similarities and differences between biomasses, the best reactors, its comparison with fossil fuels, and bio-oil upgrading methods. The upgrading mapping matrix is created to present the best upgrading strategies for the optimum quality of biofuels. This paper serves as a one-stop center for EFB conversion into biofuels.

Exotic Hydrogel Matrix as an Efficient Platform for Sustainable Production of Biomass and Lipid from Chlorella sorokiniana

Concerning the climate crisis, energy disaster, and greenhouse effects, microalgae have paved the way for consideration as a biofuel feed material. The advent of polymeric materials with unique architecture at nanoscale, in combination with microalgae, has given direction for the bioeconomic yield of highly valued compounds, essentially lipid. Herein, we discuss the paramount significance of exotic hydrogel matrix (HM) with efficient violet light absorption, far-red emission, CO₂-adsorbing capability and catalyst-free condition that could increase the photosynthesis activity, alleviating the microalgal growth for the effective augmentation of lipid, protein, and chlorophyll. The intrinsic morphological and structural features of HM were revealed by a suite of characterizations that confirm its hollow tubular architecture. Fluorescence intensity measurement confirmed the electron transfer from HM to Chlorella sorokiniana, accelerating the photosynthetic rate for the improved production of lipids (98%), proteins (60%), and chlorophyll a (121%), compared to untreated C. sorokiniana control cells. Moreover, by visualizing the Nile red (NR) fluorescence response from C. sorokiniana/HM cells, a high lipid content was observed with a larger cell size (14.6 μm) compared to control cells (8.7 μm). Fatty acid methyl esters (FAMEs), obtained from C. sorokiniana/HM, were noted with a large-scale volume of C16:C18 fatty acids (>80%). We, therefore, envisage that HM plays a significant role in enhancing the generation of lipids and proteins from C. sorokiniana. These outcomes assure a qualitative transit in the bioenergy domain.

Marine Polysaccharides: Occurrence, Enzymatic Degradation and Utilization

Macroalgae species are fast growing and their polysaccharides are already used as food ingredient due to their properties as hydrocolloids or they have potential high value bioactivity. The degradation of these valuable polysaccharides to access the sugar components has remained mostly unexplored so far. One reason is the high structural complexity of algal polysaccharides, but also the need for suitable enzyme cocktails to obtain oligo- and monosaccharides. Among them, there are several rare sugars with high value. Recently, considerable progress was made in the discovery of highly specific carbohydrate-active enzymes able to decompose complex marine carbohydrates such as carrageenan, laminarin, agar, porphyran and ulvan. This minireview summarizes these achievements and highlights potential applications of the now accessible abundant renewable resource of marine polysaccharides.

Environmentally benign solid catalysts for sustainable biodiesel production: A critical review

Versatile bio-derived catalysts have been under dynamic investigation as potential substitutes to conventional chemical catalysts for sustainable biodiesel production. This is because of their unique, low-cost benefits and production processes that are environmentally and economically acceptable. This critical review aspires to present a viable approach to the synthesis of environmentally benign and cost-effective heterogeneous solid-base catalysts from a wide range of biological and industrial waste materials for sustainable biodiesel production. Most of these waste materials include an abundance of metallic minerals like potassium and calcium. The different approaches proposed by researchers to derive highly active catalysts from large-scale waste materials of a re-usable nature are described briefly. Finally, this report extends to present an overview of techno-economic feasibility of biodiesel production, its environmental impacts, commercial aspects of community-based biodiesel production and potential for large-scale expansion.

Nitrogen, phosphorus and high CO2 modulate photosynthesis, biomass and lipid production in the green alga Chlorella vulgaris

Climate change could impact nutrient bioavailability in aquatic environment. To understand the interaction of nutrient bioavailability and elevated CO₂, Chlorella vulgaris cells were grown in ambient air or 5% CO₂ in different concentrations of nitrogen and phosphorus in a photobioreactor. The chlorophyll content, photosynthesis and respiration rates increased in 5% CO₂ to support higher biomass production. The nutrient limitation in the growth media resulted in reduced photosynthetic rates of the algal cells and their PSI, PSII, and whole chain electron transport rates and biomass production. Conversely, their lipid content increased partly due to upregulation of expression of several lipid biosynthesis genes. The order of downregulation of photosynthesis and upregulation in lipid production due to nutrient limitation was in the order of N > P. The N-50 and 5% CO₂ culture had only 10% reduction in biomass and 32% increase in lipids having 85% saturated fat required for efficient biofuel production. This growth condition is ideal for generation of biodiesel required to reduce the consumption of fossil fuel and combat global warming.

Simultaneous Fe3O4 Nanoparticle Formation and Catalyst-Driven Hydrothermal Cellulose Degradation

Breakdown and utilization of cellulose are critical for the bioenergy sector; however, current cellulose-to-energy conversion schemes often consume large quantities of unrecoverable chemicals, or are expensive, due to the need for enzymes or high temperatures. In this paper, we demonstrate a new method for converting cellulose into soluble compounds using a mixture of Fe²⁺ and Fe³⁺ as catalytic centers for the breakdown, yielding Fe₃O₄ nanoparticles during the hydrothermal process. Iron precursors transformed more than 61% of microcrystalline cellulose into solutes, with the composition of the solute changing with the initial Fe³⁺ concentration. The primary products of the breakdown of cellulose were a range of aldaric acids with different molecular weights. The nanoparticles have concentration-dependent tuneable sizes between 6.7 and 15.8 nm in diameter. The production of value-added nanomaterials at low temperatures improves upon the economics of traditional cellulose-to-energy conversion schemes with the precursor value increasing rather than deteriorating over time.

Bioethanol Production by Enzymatic Hydrolysis from Different Lignocellulosic Sources

As the need for non-renewable sources such as fossil fuels has increased during the last few decades, the search for sustainable and renewable alternative sources has gained growing interest. Enzymatic hydrolysis in bioethanol production presents an important step, where sugars that are fermented are obtained in the final fermentation process. In the process of enzymatic hydrolysis, more and more new effective enzymes are being researched to ensure a more cost-effective process. There are many different enzyme strategies implemented in hydrolysis protocols, where different lignocellulosic biomass, such as wood feedstocks, different agricultural wastes, and marine algae are being used as substrates for an efficient bioethanol production. This review investigates the very recent enzymatic hydrolysis pathways in bioethanol production from lignocellulosic biomass.

Bioprospecting of microbial strains for biofuel production: metabolic engineering, applications, and challenges

The issues of global warming, coupled with fossil fuel depletion, have undoubtedly led to renewed interest in other sources of commercial fuels. The search for renewable fuels has motivated research into the biological degradation of lignocellulosic biomass feedstock to produce biofuels such as bioethanol, biodiesel, and biohydrogen. The model strain for biofuel production needs the capability to utilize a high amount of substrate, transportation of sugar through fast and deregulated pathways, ability to tolerate inhibitory compounds and end products, and increased metabolic fluxes to produce an improved fermentation product. Engineering microbes might be a great approach to produce biofuel from lignocellulosic biomass by exploiting metabolic pathways economically. Metabolic engineering is an advanced technology for the construction of highly effective microbial cell factories and a key component for the next-generation bioeconomy. It has been extensively used to redirect the biosynthetic pathway to produce desired products in several native or engineered hosts. A wide range of novel compounds has been manufactured through engineering metabolic pathways or endogenous metabolism optimizations by metabolic engineers. This review is focused on the potential utilization of engineered strains to produce biofuel and gives prospects for improvement in metabolic engineering for new strain development using advanced technologies.

A Perspective on Biofuels Use and CCS for GHG Mitigation in the Marine Sector

The greenhouse gas (GHG) emissions of the marine sector were around 2.6% of world GHG emissions in 2015 and are expected to increase 50%–250% to 2050 under a “business as usual” scenario, making the decarbonization of this fossil fuel-intensive sector an urgent priority. Biofuels, which come in various forms, are one of the most promising options to replace existing marine fuels for accomplishing this in the short to medium term. Some unique challenges, however, impede biofuels penetration in the shipping sector, including the low cost of the existing fuels, the extensive present-day refueling infrastructure, and the exclusion of the sector from the Paris climate agreement. To address this, it is necessary to first identify those biofuels best suited for deployment as marine fuel. In this work, the long list of possible biofuel candidates has been narrowed down to four high-potential options—bio-methanol, bio-dimethyl ether, bio-liquefied natural gas, and bio-oil. These options are further evaluated based on six criteria—cost, potential availability, present technology status, GHG mitigation potential, infrastructure compatibility, and carbon capture and storage (CCS) compatibility—via both an extensive literature review and stakeholder discussions. These four candidates turn out to be relatively evenly matched overall, but each possesses certain strengths and shortcomings that could favor that fuel under specific circumstances, such as if compatibility with existing shipping infrastructure or with CCS deployment become pivotal requirements. Furthermore, we pay particular attention to the possibility of integrating deployment of these biofuels with CCS to further reduce marine sector emissions. It is shown that this aspect is presently not on the radar of the industry stakeholders but is likely to grow in importance as CCS acceptability increases in the broader green energy sector.

CO2-cofed catalytic pyrolysis of tea waste over Ni/SiO2 for the enhanced formation of syngas

To valorize tea waste (TW), catalytic pyrolysis was done as a practical measure for recovering energy as a form of syngas. Considering CO₂ as a reactive gas medium in place of conventional pyrolysis gas, a sustainable pyrolysis platform was established. In addition, mechanistic effectiveness of CO₂ on TW pyrolysis was examined. In the presence of CO₂, homogeneous reaction with volatile organic compounds (VOCs) derived from TW pyrolysis contributed to CO formation. To enhance the formation of syngas at low pyrolysis temperature, catalytic pyrolysis over a Ni/SiO₂ was investigated. The synergistic effects of Ni/SiO₂ catalyst and CO₂ promoted thermal cracking of VOCs and further homogeneous reaction with CO₂, thereby resulting in the substantial enhancement (28 times more) of H₂ and CO production than non-catalytic pyrolysis. It was also confirmed that CO₂ could be considered a reactive gas medium to produce biochar (34-35 wt.% yield), having competitive porosity and surface area, in comparison to that from pyrolysis in N₂. Therefore, CO₂ can be employed to build a sustainable waste conversion platform for energy and biochar production through pyrolysis instead of using N₂.

Effects of harvesting Spirulina platensis biomass using coagulants and electrocoagulation-flotation on enzymatic hydrolysis

This study aimed to assess the harvesting of Spirulina platensis using coagulants and electrocoagulation-flotation (ECF) and to evaluate its influence on enzymatic hydrolysis. Using nine chemical coagulants, we obtained a biomass harvesting efficiency of up to 99.5%. Using ECF, the harvesting efficiency at the aluminum and carbon electrode was 98%-99% and 33.8%-86.9%, respectively. Hydrolysis efficiency (HE) with amylases varied from 17% to 42%, and the degree of hydrolysis (DH) with proteases varied from 1.26% to 4.07%, compared with an HE of 31% and a DH of 3.57% in the centrifuged biomass. Compared to an HE of 61.75% for the centrifuged biomass, and HE of 99% and 85.46% was obtained for the biomass harvested using the aluminum and carbon electrodes. The HEs with the electrodes were better than those with the alternative methods and centrifugation; hence, with some optimization, the biomass harvested could be used for enzymatic hydrolysis.

Production of Oligosaccharides from Agrofood Wastes

The development of biorefinery processes to platform chemicals for most lignocellulosic substrates, results in side processes to intermediates such as oligosaccharides. Agrofood wastes are most amenable to produce such intermediates, in particular, cellooligo-saccharides (COS), pectooligosaccharides (POS), xylooligosaccharides (XOS) and other less abundant oligomers containing mannose, arabinose, galactose and several sugar acids. These compounds show a remarkable bioactivity as prebiotics, elicitors in plants, food complements, healthy coadyuvants in certain therapies and more. They are medium to high added-value compounds with an increasing impact in the pharmaceutical, nutraceutical, cosmetic and food industries. This review is focused on the main production processes: autohydrolysis, acid and basic catalysis and enzymatic saccharification. Autohydrolysis of food residues at 160–190 °C leads to oligomer yields in the 0.06–0.3 g/g dry solid range, while acid hydrolysis of pectin (80–120 °C) or cellulose (45–180 °C) yields up to 0.7 g/g dry polymer. Enzymatic hydrolysis at 40–50 °C of pure polysaccharides results in 0.06–0.35 g/g dry solid (DS), with values in the range 0.08–0.2 g/g DS for original food residues.

Selective elimination of phenol from hydrocarbons by zeolites and silica-based adsorbents-Impact of the textural and acidic properties

This paper investigates the parameters that influence the selective adsorption of phenol, toxic molecule, from a semi-model biofuel mixture containing alkanes and different proportions of aromatic compounds. The adsorption capacity, selectivity and regeneration ability of different adsorbents, i.e. zeolites, silica-based solids, alumina and activated carbon, were related to their textural properties and the nature, strength or location of their acidic sites. This work demonstrates that phenol differently adsorbs in the micropores and mesopores. In the micropores of faujasites, phenol is condensed into the supercages. Otherwise, in the mesopores of the zeolite, phenol interacts with the silanol groups. On purely siliceous adsorbents, a ratio of one phenol adsorbed on one silanol group could be established. As for selectivity, the strong acidic sites of the faujasites are necessary to favor phenol adsorption compared to toluene. By contrast, the amount of strong Brønsted and Lewis acid sites limits regeneration. Hence, a compromise has to be found and the best performances were obtained using a slightly dealuminated zeolitic adsorbent presenting both micro and mesopores.

Sustainable Residential Energy Supply: A Literature Review-Based Morphological Analysis

The decarbonization of the energy system will bring substantial changes, from supranational regions to residential sites. This review investigates sustainable energy supply, applying a multi-sectoral approach from a residential site perspective, especially with focus on identifying crucial, plausible factors and their influence on the operation of the system. The traditionally separated mobility, heat, and electricity sectors are examined in more detail with regard to their decarbonization approaches. For every sector, available technologies, demand, and future perspectives are described. Furthermore, the benefits of cross-sectoral integration and technology coupling are examined, besides challenges to the electricity grid due to upcoming technologies, such as electric vehicles and heat pumps. Measures such as transport mode shift and improving building insulation can reduce the demand in their respective sector, although their impact remains uncertain. Moreover, flexibility measures such as Power to X or vehicle to grid couple the electricity sector to other sectors such as the mobility and heat sectors. Based on these findings, a morphological analysis is conducted. A morphological box is presented to summarize the major characteristics of the future residential energy system and investigate mutually incompatible pairs of factors. Lastly, the scenario space is further analyzed in terms of annual energy demand for a district.

Redirecting photosynthetic electron flux in the cyanobacterium Synechocystis sp. PCC 6803 by the deletion of flavodiiron protein Flv3

Background

Oxygen-evolving photoautotrophic organisms, like cyanobacteria, protect their photosynthetic machinery by a number of regulatory mechanisms, including alternative electron transfer pathways. Despite the importance in modulating the electron flux distribution between the photosystems, alternative electron transfer routes may compete with the solar-driven production of CO₂-derived target chemicals in biotechnological systems under development. This work focused on engineered cyanobacterial Synechocystis sp. PCC 6803 strains, to explore possibilities to rescue excited electrons that would normally be lost to molecular oxygen by an alternative acceptor flavodiiron protein Flv1/3—an enzyme that is natively associated with transfer of electrons from PSI to O₂, as part of an acclimation strategy towards varying environmental conditions.

Results

The effects of Flv1/3 inactivation by flv3 deletion were studied in respect to three alternative end-products, sucrose, polyhydroxybutyrate and glycogen, while the photosynthetic gas fluxes were monitored by Membrane Inlet Mass Spectrometry (MIMS) to acquire information on cellular carbon uptake, and the production and consumption of O₂. The results demonstrated that a significant proportion of the excited electrons derived from photosynthetic water cleavage was lost to molecular oxygen via Flv1/3 in cells grown under high CO₂, especially under high light intensities. In flv3 deletion strains these electrons could be re-routed to increase the relative metabolic flux towards the monitored target products, but the carbon distribution and the overall efficiency were determined by the light conditions and the genetic composition of the respective pathways. At the same time, the total photosynthetic capacity of the Δflv3 strains was systematically reduced, and accompanied by upregulation of oxidative glycolytic metabolism in respect to controls with the native Flv1/3 background.

Conclusions

The observed metabolic changes and respective production profiles were proposedly linked with the lack of Flv1/3-mediated electron transfer, and the associated decrease in the intracellular ATP/NADPH ratio, which is bound to affect the metabolic carbon partitioning in the flv3-deficient cells. While the deletion of flv3 could offer a strategy for enhancing the photosynthetic production of desired chemicals in cyanobacteria under specified conditions, the engineered target pathways have to be carefully selected to align with the intracellular redox balance of the cells.

Deciphering the biological processes underlying tomato biomass production and composition

The huge amounts of biomass residues, remaining in the field after tomato fruits harvesting, can be utilized to produce bioenergy. A multiple level approach aimed to characterize two Solanum pennellii introgression lines (ILs), with contrasting phenotypes for plant architecture and biomass was carried out. The study of gene expression dynamics, microscopy cell traits and qualitative and quantitative cell wall chemical compounds variation enabled the discovery of key genes and cell processes involved biomass accumulation and composition. Enhanced biomass production observed in IL2-6 line is due to a more effective coordination of chloroplasts and mitochondria energy fluxes. Microscopy analysis revealed a higher number of cells and chloroplasts in leaf epidermis in the high biomass line whilst chemical measurements on the two lines pointed out striking differences in the cell wall composition and organization. Taken together, our findings shed light on the mechanisms underlying the tomato biomass production and processability.

Bioethanol production from waste lignocelluloses: A review on microbial degradation potential

Tremendous explosion of population has led to about 200% increment of total energy consumptions in last twenty-five years. Apart from conventional fossil fuel as limited energy source, alternative non-conventional sources are being explored worldwide to cater the energy requirement. Lignocellulosic biomass conversion for biofuel production is an important alternative energy source due to its abundance in nature and creating less harmful impacts on the environment in comparison to the coal or petroleum-based sources. However, lignocellulose biopolymer, the building block of plants, is a recalcitrant substance and difficult to break into desirable products. Commonly used chemical and physical methods for pretreating the substrate are having several limitations. Whereas, utilizing microbial potential to hydrolyse the biomass is an interesting area of research. Because of the complexity of substrate, several enzymes are required that can act synergistically to hydrolyse the biopolymer producing components like bioethanol or other energy substances. Exploring a range of microorganisms, like bacteria, fungi, yeast etc. that utilizes lignocelluloses for their energy through enzymatic breaking down the biomass, is one of the options. Scientists are working upon designing organisms through genetic engineering tools to integrate desired enzymes into a single organism (like bacterial cell). Studies on designer cellulosomes and bacteria consortia development relating consolidated bioprocessing are exciting to overcome the issue of appropriate lignocellulose digestions. This review encompasses up to date information on recent developments for effective microbial degradation processes of lignocelluloses for improved utilization to produce biofuel (bioethanol in particular) from the most plentiful substances of our planet.

Cyanobacteria as an eco-friendly resource for biofuel production: A critical review

Cyanobacteria are photosynthetic microorganisms which can be found in various environmental habitats. These photosynthetic bacteria are considered as promising feedstock for the production of the third- and the fourth-generation biofuels. The main subject of this review is highlighting the significant aspects of the biofuel production from cyanobacteria. The most recent investigations about the extraction or separation of the bio-oil from cyanobacteria are also adduced in the present review. Moreover, the genetic engineering of cyanobacteria for improving biofuel production and the impact of bioinformatics studies on the designing better-engineered strains are mentioned. The large-scale biofuel production is challenging, so the economic considerations to provide inexpensive biofuels are also cited. It seems that the future of biofuels is strongly dependent to the following items; understanding the metabolic pathways of the cyanobacterial species, progression in the construction of the engineered cyanobacteria, and inexpensive large-scale cultivation of them.