Photocatalytic degradation of cephalexin by UV activated persulfate and Fenton in synthetic wastewater: optimization, kinetic study, reaction pathway and intermediate products

Performance evaluation of PdO/ CuO TiO2 photocatalytic membrane on ceramic support for removing pharmaceutical compounds from water

This study investigated photocatalytic degradation of pharmaceutical compound using CuO or PdO-TiO2 membrane. The synthesized membranes were characterized by some techniques including X-ray powder diffraction (XRD), dynamic light scattering (DLS), scanning electron microscopy (SEM), and Fourier-transform infrared spectroscopy (FT-IR). The structural properties confirmed that the photocatalytic membranes were successfully prepared on ceramic supports. The PdO-TiO2 and CuO-TiO2 membranes were employed as photocatalytic membranes to degrade metronidazole (MNZ) and diphenhydramine (DPH) in aqueous solutions, respectively. Some parameters affecting the photocatalytic reaction such as pH, initial concentration, and light source were also investigated. The maximum degradation for both pharmaceutical compounds was obtained at basic pH (pH = 10), low initial concentration (C0 = 10 ppm) under UV irradiation. At high transmembrane pressure (ΔP = 3 bar), the flow rate across the membrane increased up 0.0078 and 0.0082 cc/s.cm2 for CuO-TiO2 and PdO-TiO2 photocatalytic membrane respectively while not affected on degradation efficiency (DE). At the same condition operation (C0 = 10 ppm, pH = 10, ΔP = 2 bar under UV irradiation), the MNZ and DPH degradation of the PdO-TiO2 membrane was 94 and 95% respectively that relatively higher than the CuO-TiO2 membrane. It is probably due to the lower energy band gap of PdO-TiO2 (2.5 eV) than CuO-TiO2 (2.7 eV). The membrane stability tests confirmed the high performance of the prepared membranes.

Application of Electrochemical Oxidation for Water and Wastewater Treatment: An Overview

In recent years, the discharge of various emerging pollutants, chemicals, and dyes in water and wastewater has represented one of the prominent human problems. Since water pollution is directly related to human health, highly resistant and emerging compounds in aquatic environments will pose many potential risks to the health of all living beings. Therefore, water pollution is a very acute problem that has constantly increased in recent years with the expansion of various industries. Consequently, choosing efficient and innovative wastewater treatment methods to remove contaminants is crucial. Among advanced oxidation processes, electrochemical oxidation (EO) is the most common and effective method for removing persistent pollutants from municipal and industrial wastewater. However, despite the great progress in using EO to treat real wastewater, there are still many gaps. This is due to the lack of comprehensive information on the operating parameters which affect the process and its operating costs. In this paper, among various scientific articles, the impact of operational parameters on the EO performances, a comparison between different electrochemical reactor configurations, and a report on general mechanisms of electrochemical oxidation of organic pollutants have been reported. Moreover, an evaluation of cost analysis and energy consumption requirements have also been discussed. Finally, the combination process between EO and photocatalysis (PC), called photoelectrocatalysis (PEC), has been discussed and reviewed briefly. This article shows that there is a direct relationship between important operating parameters with the amount of costs and the final removal efficiency of emerging pollutants. Optimal operating conditions can be achieved by paying special attention to reactor design, which can lead to higher efficiency and more efficient treatment. The rapid development of EO for removing emerging pollutants from impacted water and its combination with other green methods can result in more efficient approaches to face the pressing water pollution challenge. PEC proved to be a promising pollutants degradation technology, in which renewable energy sources can be adopted as a primer to perform an environmentally friendly water treatment.

The impact of material design on the photocatalytic removal efficiency and toxicity of two textile dyes

This study deals with the toxicity of the treated solutions of two types of dyes, namely, the anthraquinonic Reactive Bleu 19 dye (RB19) and the bi-azoic Direct Red 227 dye (DR227), which are treated in single and binary mixture systems. The target molecules were removed by the photocatalysis process using ZnO as a catalyst, which was calcined at two temperatures 250 and 420 °C (ZnO₂₅₀ and ZnO₄₂₀) prepared in the lab by the one-step calcination method. XRD, TEM, EDX, XPS, FT-IR, BET, RAMAN, and EPR analyses were carried out to characterize the catalyst material. While the phytotoxicity was being conducted using watercress seeds, the cytotoxicity took place using a cell line (raw) and an intestinal cell (caco-2). The XRD analysis showed the partial calcination of ZnO₂₅₀ and the presence of anhydrous zinc acetate along with the ZnO nanoparticles (NPs). This result was not observed for ZnO₄₂₀. Despite the complete discoloration (100%) of all the final solutions, ZnO₂₅₀ exhibited a high cytotoxicity and phytotoxicity against the RB19 dye after the photocatalytic treatment; however, it was not the case of ZnO₄₂₀ which was selected as an eco-friendly photocatalyst for the degradation of organic dyes based on the results of removal efficiency, cytotoxicity, and phytotoxicity.

A comprehensive review on persulfate activation treatment of wastewater

With increasingly serious environmental pollution and the production of various wastewater, water pollutants have posed a serious threat to human health and the ecological environment. The advanced oxidation process (AOP), represented by the persulfate (PS) oxidation process, has attracted increasing attention because of its economic, practical, safety and stability characteristics, opening up new ideas in the fields of wastewater treatment and environmental protection. However, PS does not easily react with organic pollutants and usually needs to be activated to produce oxidizing active substances such as sulfate radicals (SO₄^-) and hydroxyl radicals (OH) to degrade them. This paper summarizes the research progress of PS activation methods in the field of wastewater treatment, such as physical activation (e.g., thermal, ultrasonic, hydrodynamic cavitation, electromagnetic radiation activation and discharge plasma), chemical activation (e.g., alkaline, electrochemistry and catalyst) and the combination of the different methods, putting forward the advantages, disadvantages and influencing factors of various activation methods, discussing the possible activation mechanisms, and pointing out future development directions.

Cephalexin removal by persulfate activation using simulated sunlight and ferrous ions

This study presents the main results related to the use of activated persulfate (PS) in the elimination of the beta-lactam antibiotic cephalexin (CPX). Experiments were done using K₂S₂O₈ and simulated sunlight. A face-centered central composite experimental design was used to analyze the effects of the solution pH and the PS concentration on the reaction, and to determine the optimized conditions that favor the CPX elimination. The results indicated that the removal of CPX is promoted by an acidic pH and under the higher evaluated PS dose (7.5 mg L^-1). CPX total removal was achieved in 30 min. The analysis of the effect of the pollutant initial concentration indicated that a pseudo-first-order kinetics model can be used to describe the reaction. Likewise, the use of Fe²⁺ ions for PS activation (in the dark) was evaluated and established that a higher concentration of ions favors the pollutant removal. Control tests and under the presence of scavenger agents indicated that both HO• and SO₄^-• radicals would be present in the solution and promote the CPX elimination. The assessment of the solution dissolved organic carbon, nitrates and sulfates was also carried out, and indicated that a portion of the organic matter was mineralized.

Cephalexin removal by a novel Cu-Zn bionanocomposite biosynthesized in secondary metabolic products of Aspergillus arenarioides EAN603 with pumpkin peels medium: Optimization, kinetic and artificial neural network models

The present study aimed to investigate the removal efficiency of cephalexin (CFX) by a novel Cu-Zn bionanocomposite biosynthesized in the secondary metabolic products of Aspergillus arenarioides EAN603 with pumpkin peels medium (CZ-BNC-APP). The optimization study was performed based on CFX concentrations (1, 10.5 and 20 ppm); CZ-BNC-APP dosage (10, 55 and 100 mg/L); time (10, 55 and 100 min), temperature (20, 32.5 and 45 °C). The artificial neural network (ANN) model was used to understand the CFX behavior for the factors affecting removal process. The CZ-BNC-APP showed an irregular shape with porous structure and size between 20 and 80 nm. The FTIR detected CC, C-O and OH groups. ANN model revealed that CZ-BNC-APP dosage exhibited the vital role in the removal process, while the removal process having a thermodynamic nature. The CFX removal was optimized with 12.41 ppm CFX, 60.60 mg/L of CZ-BNC-APP, after 97.55 min and at 35 °C, the real maximum removal was 95.53% with 100.52 mg g^-1 of the maximum adsorption capacity and 99.5% of the coefficient. The adsorption of CFX on CZ-BNC-APP was fitted with pseudo-second-order model and both Langmuir and Freundlich isotherms models. These findings revealed that CZ-BNC-APP exhibited high potential to remove CFX.

Sustainable approaches for removal of cephalexin antibiotic from non-clinical environments: A critical review

In this article, the removal of cephalexin (CFX) antibiotic from non-clinical environment is reviewed. Adsorption and photocatalytic degradation techniques are widely used to remove CFX from waters and wastewaters, the combination of these methods is becoming more common for CFX removal. The treatment methods of CFX has not been reviewed before, the present article aim is to organize the scattered available information regarding sustainable approaches for CFX removal from non-clinical environment. These include adsorption by nanoparticles, bacterial biomass, biodegradation by bacterial enzymes and the photocatalysis using different catalysts and Photo-Fenton photocatalysis. The metal-organic frameworks (MOFs) appeared to have high potential for CFX degradation. It is evident from the recently papers reviewed that the effective methods could be used in place of commercial activated carbon. The widespread uses of photocatalytic degradation for CFX remediation are strongly recommended due to their engineering applicability, technical feasibility, and high effectiveness. The adsorption capacity of the CFX is ranging from 7 mg CFX g^-1 of activated carbon nanoparticles to 1667 mg CFX g^-1 of Nano-zero-valent iron from Nettle. In contrast, the photo-degradation was 45% using Photo-Fenton while has increased to 100% using heterogeneous photoelectro-Fenton (HPEF) with UVA light using chalcopyrite catalyst.