Analysis of erythromycin estolate by liquid chromatography

Liquid chromatography of troleandomycin

Until now no liquid chromatography (LC) method is described to determine the purity and content of troleandomycin and its related substances. A simple, robust, sensitive and selective isocratic liquid chromatographic method suitable for the determination of the antibiotic troleandomycin and its related substances is described. This method utilizes as a stationary phase: XTerra RP18 5 microm (25 cm x 4.6 mm I.D.) at 30 degrees C and as mobile phase: acetonitrile-0.2 M ammonium acetate buffer (pH 6.0)-water (45:5:50, v/v), delivered at a flow-rate of 1.0 ml/min. UV detection is performed at 205 nm. Troleandomycin is separated from the partially acetylated related substances and from several unknown impurities present in commercial samples. The robustness of the method was evaluated by a full-factorial experimental design.

Analysis of a commercial preparation of erythromycin estolates by tandem mass spectrometry and high performance liquid chromatography/electrospray ionization tandem mass spectrometry using an ion trap mass spectrometer

Because of the lack of a UV chromophore and their much smaller abundances in comparison with the major component, the minor components in erythromycin estolate preparations are difficult to analyze by high performance liquid chromatography ultraviolet (HPLC-UV). Tentative assignment of the major and minor components can be achieved with the combination of full scan and ZoomScan using an ion trap mass spectrometer. Tandem mass spectrometry (MS/MS) provided an effective method to quickly identify most components without chromatographic separation, and all the related compounds, except the isobaric pair ECE and PdMeEA, could be identified in this way. The best result was obtained by using liquid chromatography/tandem mass spectrometry (LC/MS/MS) operated in selected reaction monitoring mode. The major compound, the estolate of erythromycin A (EAE), and seven other minor components, could be separated and identified, with semiquantitative estimates of relative concentrations.

Analysis of macrolide antibiotics

The following macrolide antibiotics have been covered in this review: erythromycin and its related substances, azithromycin, clarithromycin, dirithromycin, roxithromycin, flurithromycin, josamycin, rokitamycin, kitasamycin, mycinamycin, mirosamycin, oleandomycin, rosaramicin, spiramycin and tylosin. The application of various thin-layer chromatography, paper chromatography, gas chromatography, high-performance liquid chromatography and capillary zone electrophoresis procedures for their analysis are described. These techniques have been applied to the separation and quantitative analysis of the macrolides in fermentation media, purity assessment of raw materials, assay of pharmaceutical dosage forms and the measurement of clinically useful macrolide antibiotics in biological samples such as blood, plasma, serum, urine and tissues. Data relating to the chromatographic behaviour of some macrolide antibiotics as well as the various detection methods used, such as bioautography, UV spectrophotometry, fluorometry, electrochemical detection, chemiluminescence and mass spectrometry techniques are also included.

Sensitive determination of erythromycin in human plasma by LC-MS/MS

A liquid chromatography-tandem mass spectrometry (LC-MS/MS) method for the analysis of erythromycin in human plasma (EDTA as anticoagulant) was developed and validated. The concentration ranges were 0.5-50 and 50-5000 ng ml-1. The procedure involved alkalization of 0.5 ml of plasma, one step liquid-liquid extraction, dryness of the extract and reconstitution in 80:20 water:acetonitrile. An Inertsil ODS-2 5 microns, 3.0 x 50 mm column (Metachem) with a C8 guard column and isocratic mobile phase were used for liquid chromatography. The mobile phase consisted of 1:1 acetonitrile:water with 2 mM NH4OAc and 0.1% HOAc. A flow rate of 0.7 ml min-1 was used. The analysis time on LC-MS/MS for one sample was approximately 2 min. A Turbo-Ionspray source was interfaced between the HPLC and triple quadrupole mass spectrometer (Sciex API III Plus). MS/MS analysis used Multi-Reaction Monitoring (MRM) mode. The lowest limit of quantitation (LOQ) was 0.5 ng ml-1 with all Quality Control (QC) sample recoveries varying between 88 and 105%. Nine intraday and interday calibration curves were generated yielding correlation coefficients ranging from 0.995 to 1.000. Average recovery for erythromycin at 1 ng ml-1 was 105% (+/- 4.5%). Average recovery for the internal standard was 83-103%. Short-term and long-term stability in the freezer (-20 degrees C), bench stability, and stability after 3 freeze/thaw cycles at -20 and -80 degrees C were conducted. The samples were found to be stable under all conditions. The method developed and validated proved useful for clinical pharmacokinetic study sample analysis with high throughput due to its high sensitivity and very short analysis time.

Analysis of macrolide antibiotics by capillary electrophoresis

Capillary electrophoresis was utilized in the study of the macrolide antibiotics (i.e. pharmaceutical glycoconjugates) clarithromycin, erythromycin, oleandomycin, troleandomycin, and spiramycin. In order to assist in analyte solubilization, two buffer systems using acetonitrile were developed. The first system involved 30 mM sodium cholate and 20% acetonitrile in 80 mM sodium phosphate, pH 6. This buffer permitted the baseline resolution of all five glycoconjugated antibiotics. In addition, erythromycin was separated from its derivatives estolate and ethylsuccinate. In the absence of surfactants, a higher acetonitrile quantity, 65%, was used in the second buffer system, with 35 mM sodium phosphate, pH 6. Selectivity between oleandomycin and clarithromycin was reversed in this system compared to the cholate buffer, indicating solute interaction with the cholate micelles in the previous system. Calibration linearity and detection sensitivity were improved in the high acetonitrile buffer, due to decreased background absorbance. It was demonstrated that both buffer systems can be utilized for the visualization of minor components that may be present in bulk pharmaceuticals.