Commercially available archwire forms compared with normal dental arch forms in a Japanese population

The dimensions of preformed nickel-titanium archwires measured at the bracket positions corresponding to the central incisor, canine, and first molar

INTRODUCTION

Variation in the thickness of commercially available preformed rectangular archwires at the bracket positions has not been thoroughly studied. Therefore, this study measured the edgewise (height) and flatwise (width) dimensions of preformed rectangular nickel-titanium (NiTi) archwires at bracket positions corresponding to the central incisor, canine, and first molar and compared them among bracket positions.

METHODS

Sixty types of preformed rectangular NiTi mandibular archwires indicated as 0.019 × 0.025-in were obtained from 14 manufacturers. The height and width dimensions of archwires were measured at 4 points (3 bracket positions corresponding to the central incisor, canine, and first molar, and 1 terminal end) of each side of each archwire using a micrometer and compared with the indicated dimensions using 1-sample t tests. Furthermore, the measured dimensions were compared among the 3 bracket positions using a 1-way analysis of variance and Bonferroni post-hoc test.

RESULTS

The measured dimensions were significantly smaller than the indicated dimensions for all points except the central incisor point for height and significantly smaller than the indicated dimensions for all points for width. Comparisons among points showed that for height, the central incisor point was significantly larger than the first molar and terminal points. However, no significant differences were found for width at any point.

CONCLUSIONS

The measured dimensions of preformed NiTi archwires at the bracket positions were generally smaller than the indicated dimensions, with variations observed not only among products but also among manufacturers.

Analysis of the Facial Measurements and Dental Arch Dimensions for the Construction of Dental Prostheses among Adult Yemenis

AIM

To investigate the dental arch dimension (width, length, and height) and facial measurements including inner-canthal width (ICW), bizygomatic width (BZW), inter-alar width (IAW), and mouth width (MW), and to assess the correlation between these facial measurements and dental arch width (canine width [CW], inter-first premolar width [I1PW], and inter-first molar width [I1MW]), to establish a preliminary reference for artificial teeth selection in Yemeni adult.

MATERIALS AND METHODS

The study included 80 individuals (40 males and 40 females) with symmetrical faces and normal class I occlusion ranging in age from 20 to 35. Maxillary and mandibular stone casts were made for each individual. The dimensions of dental casts and facial measurements, including ICW, BZW, IAW, and MW, were assessed using a digital caliper. The collected data were analyzed by using the SPSS software program. The descriptive statistics for each measurement were made. Differences between males and females were tested using an independent-sample t-test with p-values below 0.05 considered significant. Pearson correlation coefficient between facial measurements and dental arch width was also done.

RESULTS

Most dental arch dimensions and facial measurements exhibited larger mean values in the male than in the female group, with the greatest significant difference in the maxillary dental arch width and the lowest in mandibular dental arch length. A highly significant correlation is observed between ICW and maxillary canine width (CW) (r = 0.318, p = 0.004). In contrast, no significant correlation between dental arch width and BZW, IAW, and MW is shown.

CONCLUSIONS

Within this study's limitations, the ICW can determine the ideal dimension of the artificial teeth in the anterior maxillary arch. While the other facial parameters, including BZW, IAW, and MW, cannot be used for artificial teeth selection in Yemeni populations.

CLINICAL SIGNIFICANCE

The findings of this study established a reference database of facial measurements and their correlation to dental arch and teeth width in Yemeni populations. So, it can be implemented in artificial teeth and dental prostheses design and construction.

Mandibular Clinical Arch Forms in Iraqi Population: A National Survey

Background: This study aims to identify mandibular clinical arch forms and dimensions in the Iraqi population. Materials and methods: The study sample consisted of pre-treatment mandibular study models of the Iraqi population. The most labial aspect of 13 proximal contact areas was digitized using AutoCAD software to determine the clinical bracket point for every tooth. The dental arches were classified into three types: tapered, ovoid, and square. The arch dimensions were identified using four linear and two proportional measurements. Results: A total of 1005 study models were collected. The arch forms were distributed as ovoid (47%), tapered (36.2%), and square (16.8%), with no significant difference in the distribution between Arabs and Kurds. The ovoid arch form was predominant in class I and class III malocclusion, while the tapered arch form was predominant in class II. All the linear measurements were greater in the males than in the females. The arch widths decreased as the arch form shifted from square to ovoid to tapered, while the arch depths showed the reverse relation. Conclusions: According to this study, ovoid and tapered archwires should suit the majority of Iraqi patients. The ovoid arch form was the most predominant in the subjects with class I and class III malocclusion, while the tapered arch form was the most predominant in the class II subjects.

Impact of the prefabricated forms of NiTi archwires on orthodontic forces delivered to the mandibular dental arch

BACKGROUND

Although preformed archwires with a variety of arch forms are currently commercially available, the effects of variation in the shape of these archwires on the orthodontic force at each tooth are not well understood. Therefore, we evaluated the forces delivered by various types of commercially available preformed nickel-titanium alloy (NiTi) archwires in a simulated mandibular dental arch.

METHODS

Sixty-three types of 0.019 × 0.025-inch preformed NiTi archwires from 15 manufactures were selected for analysis. The intercanine width (ICW) and intermolar width (IMW) of each archwire were measured at the mean canine and first molar depths of 30 untreated subjects with normal occlusions. Each archwire was placed in a multi-sensor measurement system simulating the mandibular dental arch of subjects with normal occlusions, and orthodontic forces in the facial-lingual direction at the central incisors, canines, and first molars were measured. Correlations between the ICW, IMW, and ICW/IMW ratio of archwires and the delivered forces were analyzed. The archwires were classified into the following four groups according to the ICW and IMW: Control group, ICW and IMW are within the means ± standard deviations of the normal ranges; Ovoid group, narrow ICW and IMW; Tapered group, narrow ICW; and Square group, narrow IMW. The forces were compared among these groups for each tooth.

RESULTS

Significant correlations between the measured archwire width and force to each tooth were found, except between IMW and forces at the central incisors and canines. Significant differences in the forces were found among all groups, except between the Ovoid and Tapered groups at all teeth and between the Ovoid/Tapered and Control groups at the first molar. Significantly greater orthodontic forces in the facial direction were delivered at the central incisors by the archwires in the Ovoid and Tapered groups when compared with the archwires in the other groups.

CONCLUSION

These findings suggest that there is a possible risk of a clinically significant level of unfavorable orthodontic force being delivered to the mandibular incisors in labial inclination when using a preformed archwire with an ICW that is narrower than the dental arch.

In vitro comparison of the mechanical behaviour of archwires after computer-assisted and conventional bracket positioning protocols

INTRODUCTION

The mechanical properties of orthodontic archwires can be defined using experimental setups incorporating brackets that provide conditions closer to those encountered in vivo. We aimed to compare a methodology based on computer-aided design with the gold standard protocol, performed when brackets are engaged to a full-size archwire to test the behaviour of wires in this condition.

METHODS

Three models simulating a dental arch with an orthodontic fixed appliance (0.018-inch aesthetic conventional brackets) were designed. The brackets were positioned with a stainless-steel full-size wire on the first two models, with different interbracket distances. The setup 3, based on a computer-assisted design, allowed individualized placement of each bracket. Mean forces recorded and standard deviation were compared for a 0.016×0.022-inch copper-nickel-titanium wire deflected until 2mm.

RESULTS

The inter-bracelet distances do not cause a statistical difference in the average maximum force recorded (12.6N and 11.4N; P=0.081) whereas the behaviour of the wires is affected. With setup 3, the recorded efforts (mean value: 8N) are statistically lower than with setup 1 and 2 respectively (P=0.018; P=0.012).

CONCLUSION

An individualization of the housings by CAD-CAM dedicated to each bracket optimizes their placement. In our test conditions, the mechanical behaviour of the wires is more influenced by the positioning methods of the brackets than by the value of the interbracket distance. In perspective, our innovative methodology can be extended to other types of brackets.

3D technology to measure dental arches and create a template for lingual brackets technique

Objective:

This study aims at identifying anatomical dimensions of dental arches, based on landmarks currently used in the lingual orthodontic technique, and create an archwire form template to be used in orthodontic clinics.

Methods:

Maxillary and mandibular dental casts of 140 Caucasian individuals with natural and normal occlusion were digitized (3D), and the images were analyzed with Delcam Power Shape^TM 2010 software. The dental arch shapes and sizes were obtained from 14 landmarks selected on the lingual surface of the teeth. Points and segments defined by the software were used to create an archwire form template.

Results:

Various dental arch patterns were found for both maxilla and mandible. The smallest sizes were found in females, and the largest were found in male subjects. Six categories were defined for each gender, three for the maxilla and three for the mandible (Small, Medium and Large). A template was created with eighteen anatomic lingual archwire designs, nine for the maxilla and nine for the mandible, for both genders.

Conclusions:

Landmarks evaluated in this study showed dental arch differences between genders. This information enables making orthodontic lingual archwires that are more compatible with the anatomical forms and sizes of the maxilla and mandible. The findings also allowed the creation of a template for an anatomic lingual metallic archwire form to be used in the lingual technique.

Fully automated estimation of arch forms in cone-beam CT with cubic B-spline approximation: Evaluation of digital dental models with missing teeth

BACKGROUND AND OBJECTIVE

To evaluate the automatic determination method for the arch form in cone-beam computed tomography (CBCT) images with cubic B-spline approximation on digital dental models using various types of missing teeth.

METHODS

The maxilla and mandible from eight dental CBCT images with Class I occlusion and no missing teeth were used in this study. The dental arch determination algorithm using cubic B-spline approximation was modified by applying a smoothing function for reliable curve fitting to the digital dental models with various types of missing teeth. For evaluation, 31 scenarios with missing teeth were simulated, and cases with 1-8 missing teeth were divided into three groups: solitary, consecutive, and multiple (more than 4) missing teeth. The prediction accuracies of the dental arch forms were evaluated through comparisons with the gold standards for the digital dental models by two expert orthodontists.

RESULTS

The distance errors between the gold standards and the estimated results of the dental arch forms in all types of models were 0.237-1.740 mm. The mean distance errors of the solitary, consecutive, and multiple groups were 0.436 ± 0.124 mm (0.237-0.964 mm), 0.591 ± 0.250 mm (0.256-1.482 mm), and 0.679 ± 0.310 mm (0.254-1.740 mm), respectively.

CONCLUSIONS

The algorithm for predicting the arch form functioned reliably, even for digital dental models with various types of missing teeth, and could be applied to digital dentistry for applications such as orthodontic tooth setup, artificial tooth arrangement for denture fabrication, and implant guides.

Impact of passive self-ligation and conventional elastic ligation on orthodontic force in the simulation of a mandibular lateral incisor linguoversion

INTRODUCTION

This study compared three-dimensional forces delivered to the displaced tooth and its adjacent teeth between passive self-ligation (PSL) and conventional elastic ligation (CL) in simulation of mandibular lateral incisor linguoversions.

METHODS

A multisensor system was used to measure three-dimensional forces delivered to brackets attached to the mandibular left central incisor, lateral incisor, and canine (FDI tooth numbers 31, 32, and 33, respectively). Two ligation methods (PSL and CL), 3 nickel-titanium (0.014-inch) archwires similar to the arch form of normal occlusion, and 2 displacements (1 and 4 mm) were tested.

RESULTS

In 1-mm displacement, forces were significantly smaller in CL than in PSL at 32 in the labial direction and larger at 31 in the mesial direction for all 3 types of archwires (P <0.01 for both). For 2 of 3 archwires, forces were larger in CL than in PSL at 33 in the lingual direction (P <0.01). In 4-mm displacement, forces were significantly larger in CL than in PSL at 31 in the mesial direction and significantly smaller in CL than in PSL at 33 in the distal direction for all 3 archwires (P <0.05 and P <0.01, respectively). Mean forces in the vertical direction were small, ranging from -0.05 to 0.05 N.

CONCLUSIONS

Under a small amount of displacement, force magnitude in PSL was smaller than that in CL at the displaced tooth in labial-lingual directions. Under a large amount of displacement, a more "open coil spring effect" was significantly obtained in CL than PSL at both adjacent teeth of the displaced tooth.

The effect of electro-thermal treatment of stainless steel arch wire on mechanical properties and cell proliferation

Background

Electric resistance heat treatment may be performed on orthodontic arch wires, but it remains unclear whether this procedure reliably provides better mechanical properties or whether an austenite phase transition affords less cytotoxicity and less arch wire width change.

Methods

Stainless steel (SS) arch wires of 0.017 × 0.025 and 0.019 × 0.025 inches in size were heat-treated using a spot welder for eight seconds at power settings of 2, 4, 6 and 8. The surface morphology, coefficient of friction (COF), flexural modulus, cytotoxicity, austenitic content, colour change and arch width of the samples were subsequently analysed.

Results

The COF, flexural modulus and austenitic content of the orthodontic SS arch wires increased after heat treatment. SS wires appearing brownish-yellow and blue exhibited higher flexural moduli. The heat treatment of the SS wires did not significantly increase arch wire width or cause cytotoxicity.

Conclusions

Electric resistance heat treatment of SS arch wires is a feasible method to improve the flexural modulus without widening the arch wire and increasing cytotoxicity. The colour of the wire helps determine the heating status, and the maximum flexural modulus of the wires is obtained when the colour changes to brownish-yellow.

Evaluation of conformity of preformed orthodontic archwires and dental arch form

Introduction:

The alterations in the arch form during treatment are dictated by the dimensions of the archwires.

Objective:

This study aimed to determine the mean arch dimensions of a sample of Pakistani subjects and to evaluate the conformity of preformed archwires with mandibular arch form.

Methods:

The dental records of 1,500 adult subjects were evaluated. The mandibular casts of 42 subjects (males = females = 21) with balanced facial profile, Class I occlusion, ideal overjet and overbite were included. Brackets were bonded on all teeth. Arch dimensions were evaluated at canines, first premolars, second premolars, first and second molars, with digital vernier calipers. The arch widths at the level of aforementioned teeth were evaluated on the digitized archwires, using the mean arch depths of the subjects.

Results:

In males, the archwires were found to be wider at canines and premolars, and significantly narrower at first (p< 0.001, 95% CI = 2.03 - 5.74) and second molars (p< 0.001, 95% CI = 2.29 - 7.73) as compared to the arch dimensions of the mandibular casts. In females, the archwires were significantly narrower at canines (p< 0.001, 95% CI = 1.4 - 3.97), and first (p= 0.02, 95% CI = 0.402 - 4.41) and second molars (p< 0.001, 95% CI = 1.76 - 6.13).

Conclusion:

No single commercially available archwires evaluated in the present study conformed to the arch dimensions of our subjects. Utilization of the currently available archwires may result in unwarranted modification of arch form, which may lead to unstable post-treatment teeth position.

The effect of occlusogingival placement of clinical bracket points on the adaptation of a straight wire to the lingual arch form

Objective

The aim of this study is to compare the adaptation of a straight wire between brackets positioned at the mid-lingual surface and those placed gingivally by using a three-dimensional simulation software.

Methods

This cross-sectional study was performed using OrthoAid, an in-house software. The subjects were 36 adolescents with normal Class I occlusion. For each dental cast, two bracket positioning approaches, namely the middle and gingival, were examined. In the middle group, the reference points were placed on the mid-lingual surface of each tooth, while in the gingival group, the reference points were positioned lingually on the anterior teeth. A 4th degree polynomial was adopted, and the in-plane and off-plane root mean squares (RMSs) of the distances between the reference points and the fitted polynomial curve were calculated using the software. Statistical analysis was performed using the paired-samples t-test (α = 0.05).

Results

The mean in-plane RMS of the polynomial curve to the bracket distance in the gingival group was significantly lower than that in the middle group (p < 0.001). The off-plane RMS was higher in the gingivally positioned brackets in the maxilla than in the middle group (p < 0.001). However, the off-plane RMS in mandible was not statistically significantly different between the two groups (p = 0.274).

Conclusions

The results demonstrated that the gingival placement of lingual brackets on the anterior teeth could decrease the distance between a tooth and the straight wire.

Human evaluation in association to the mathematical analysis of arch forms: Two-dimensional study

OBJECTIVES

To evaluate the relationship between human evaluation of the dental-arch form, to complete a mathematical analysis via two different methods in quantifying the arch form, and to establish agreement with the fourth-order polynomial equation.

MATERIALS AND METHODS

This study included 64 sets of digitised maxilla and mandible dental casts obtained from a sample of dental arch with normal occlusion. For human evaluation, a convenient sample of orthodontic practitioners ranked the photo images of dental cast from the most tapered to the less tapered (square). In the mathematical analysis, dental arches were interpolated using the fourth-order polynomial equation with millimetric acetate paper and AutoCAD software. Finally, the relations between human evaluation and mathematical objective analyses were evaluated.

RESULTS

Human evaluations were found to be generally in agreement, but only at the extremes of tapered and square arch forms; this indicated general human error and observer bias. The two methods used to plot the arch form were comparable.

CONCLUSION

The use of fourth-order polynomial equation may be facilitative in obtaining a smooth curve, which can produce a template for individual arch that represents all potential tooth positions for the dental arch.

Study of the adaptability of preformed orthodontic archwires to the average dental arch form of a Moroccan population

INTRODUCTION

The aim of this study is to determine which commercially available preformed archwires offer a good fit with the average dental arch form of our sample.

MATERIALS AND METHOD

We measured the dental arch parameters of sample 1 comprising 30 dental models and compared them with the dimensions of 25 archwires (sample 2) offered for sale by orthodontic suppliers.

RESULTS AND DISCUSSION

Of the 25 archwires tested, 10 correspond perfectly to the average dental arch form of our sample at canine and molar level (mean±1SD) and would be suitable for cases where the treatment plan involves no expansion. In addition, 3 archwires have a shape that is slightly wider than the average arch form in the sample and could be used for cases in which the treatment plan includes no extractions but simply a slight expansion.

Variation in form of mandibular, light, round, preformed NiTi archwires

OBJECTIVE

To evaluate the variation in form of nickel-titanium (NiTi) archwires by comparing them with the dental arch form of normal Japanese subjects before and after placing them in the first molar tubes.

MATERIALS AND METHODS

The mandibular dental casts of 30 normal subjects were scanned, and the dental arch depths and widths from the canine to the first molar were measured. Standardized images of 34 types of 0.016-inch preformed NiTi archwires were also taken in a 37°C environment, and the widths were measured and then classified by cluster analysis. Images of these archwires placed in a custom jig with brackets attached at the mean locations of the normal mandibular central incisors and first molar were additionally taken. The widths of the pooled and classified archwires were then compared with the normal dental arch widths before and after placement in the jig and among the groups (P < .05).

RESULTS

The archwires were classified into three groups: small, medium, and large. The archwire widths in the small and medium groups were narrower than those at all examined tooth widths, except in the case of the premolars of the medium group. After placement in the jig, the pooled archwire widths were found to be significantly narrower and wider at the canine and second premolar, respectively, than at the dental arch, but not in the individual comparisons between groups.

CONCLUSION

The variation observed in the mandibular NiTi archwire forms significantly decreased following fitting into the normal positions of the first molars.

Comparison of dental and alveolar arch forms between different ethnic groups

OBJECTIVE

The aims of this study were to evaluate, by means of 3D software, any correlation between ethnic group and the shape and size of the dental arcade and its bony support, and to investigate the correspondence between the latter two variables within each ethnic group. The data gathered were also compared with the measurements of commercially available pre-formed archwires to determine which provide the best fit for each arch in each group.

MATERIALS AND METHODS

The shape and size of the dental and alveolar arches of 29 subjects of African origin and 37 Caucasian subjects were compared in terms of linear inter-canine, inter-premolar and inter-molar measurements, overall arch length, and the distance between each tooth and the reference occlusal plane. To determine which pre-formed archwires are best suited to each of the two ethnic groups, the in-out of the brackets was considered, simulating their presence in the oral cavity.

RESULTS

The upper and lower dental and alveolar arches were all wider and longer in African with respect to Caucasian subjects (P<0.05). In general, "Roth small" (index value 1.556) and "Ideal Form Medium" (index value 0.645) archwires were better suited to both upper and lower arcades in the latter group, while "Damon" (index value 1.447) and "Ideal Form Large" (index value 1.695) conformed better to the size and shape of both arcades in the former.

CONCLUSIONS

There are very significant differences in arch form between the two ethnic groups considered, and the range of pre-formed archwires on the market does not provide for the anatomical variability of patients.

Clinical Implications of Preformed Archwire Selection on the Treatment of Angle Class I/II division 1 Malocclusions in Thais

INTRODUCTION

The dental arch forms were compared of untreated Class I and Class II div 1 malocclusions to those of non-customized preformed archwires manufactured by American Orthodontics, G&H, Highland, Ormco, RMO, and 3MUnitek. Arch forms of post-treatment Class II div 1 malocclusions treated by four 1st premolar extractions are also compared.

MATERIALS AND METHODS

Four metrics of archform shape and size (canine and 1(st) molar depth and inter-canine and inter 1(st) molar width) were measured on dental casts of 40 Class I and 22 Class II div 1 patients. These same metrics were also used to describe preformed archwire forms.

RESULTS

Non-customized preformed wires all showed significantly narrowed mandibular arch forms. This was true for maxillary archwires, with four exceptions. The Highland Natural Arch form, G&H True form I, and RMO natural preformed archwires showed both inter-canine and 1(st) molar widths statistically the same as mean dental arch widths in both the untreated and post-treatment Class II groups. In Class I patients, these three archwires showed only inter-canine widths equivalent to dental measurements. The Highland Progressive archwire matched only the 1(st) molar width in the untreated Class II group.

CONCLUSION

None of these archwires - if used unadjusted, will produce a significant expansive force in either the maxillary or mandibular arch. Three maxillary non-customized preformed archwires showed both inter-canine and 1(st) molar arch widths statistically the same as Thai Class II div 1 dental arch dimensions. Using them to treat this malocclusion should minimally affect both pre and post-treatment maxillary arch form.

Is arch form influenced by sagittal molar relationship or Bolton tooth-size discrepancy?

Background

Orthodontic patients show high prevalence of tooth-size discrepancy. This study investigates the possible association between arch form, clinically significant tooth-size discrepancy, and sagittal molar relationship.

Methods

Pretreatment orthodontic casts of 230 Saudi patients were classified into one of three arch form types (tapered, ovoid, and square) using digitally scanned images of the mandibular arches. Bolton ratio was calculated, sagittal molar relationship was defined according to Angle classification, and correlations were analyzed using ANOVA, chi-square, and t-tests.

Results

No single arch form was significantly more common than the others. Furthermore, no association was observed between the presence of significant Bolton discrepancy and the sagittal molar relationship or arch form. Overall Bolton discrepancy is significantly more prevalent in males.

Conclusions

Arch form in a Saudi patient group is independent of gender, sagittal molar relationship, and Bolton discrepancy.

Influences of archwire size and ligation method on the force magnitude delivered by nickel-titanium alloy archwires in a simulation of mandibular right lateral incisor linguoversion

The present study investigated the influence of archwire size and ligation method on the force magnitude delivered by nickel-titanium alloy archwires to 4 incisor brackets (42, 41, 31, and 32) in a simulation of mandibular right lateral incisor linguoversion. The force delivered by 0.014 and 0.016 inch nickel-titanium alloy archwires was measured using a newly developed multi-sensor measuring system and the mean force magnitudes were compared between different archwire sizes when using conventional ligation (CL) with elastic modules or self-ligating (SL) brackets by three-way ANOVA and post-hoc Bonferroni's tests. The mean force magnitudes for the brackets were significantly decreased in the order of 42, 41, 31, and 32 (p<0.01). The force magnitude was significantly larger in CL than SL at 42, 31, and 32 (p<0.05). In conclusion, the ligation method affected the force magnitude at 4 incisor brackets. Despite the ligation method, archwire size affected the force magnitude from 42 to 31.

Determining shapes and dimensions of dental arches for the use of straight-wire arches in lingual technique

INTRODUCTION:

This study aims to determine the shape and dimension of dental arches from a lingual perspective, and determine shape and size of a straight archwire used for lingual Orthodontics.

METHODS:

The study sample comprised 70 Caucasian Brazilian individuals with normal occlusion and at least four of Andrew's six keys. Maxillary and mandibular dental casts were digitized (3D) and the images were analyzed by Delcam Power SHAPET 2010 software. Landmarks on the lingual surface of teeth were selected and 14 measurements were calculated to determine the shape and size of dental arches.

RESULTS:

Shapiro-Wilk test determined small arch shape by means of 25^th percentile (P25%) - an average percentile for the medium arch; and a large one determined by means of 75^th percentile (P75%). T-test revealed differences between males and females in the size of 12 dental arches.

CONCLUSION:

The straight-wire arch shape used in the lingual straight wire technique is a parabolic-shaped arch, slightly flattened on its anterior portion. Due to similarity among dental arch sizes shown by males and females, a more simplified diagram chart was designed.

Dental and alveolar arch forms in a Caucasian population compared with commercially available archwires

INTRODUCTION

The aim of this study was to identify an arch form, comprising dentition and alveolus, representative of the Caucasian population, and to compare it with the shape of the main archwires on the market.

MATERIALS AND METHODS

The study sample comprised 35 pairs of dental casts, taken from the arches of 35 Southern Europeans with ideal natural occlusion. After the dental casts were scanned, the reference points of the dental arches (FA points) and alveolar bone (WALA ridges) were identified with 3D software. Cartesian coordinates and intercanine and intermolar diameters were calculated for each patient, and curves representing the upper and lower dentition, as well as those showing the shape of the lower supporting bone, were traced and compared with those pertaining to different types of commonly used orthodontic archwires.

RESULTS

Ideal shapes of the mandibular alveolus and of the upper and lower archwires were calculated and compared with those actually on the market. Statistical analysis showed significant differences between the two, particularly at the upper and lower molars and canines. Likewise, there were significant differences between the shapes of the available archwires and the WALA ridge, except for the intercanine width.

CONCLUSIONS

None of the commercial archwires examined faithfully represented the shape of the 'ideal' dentition we calculated, particularly at the molars and canines. The bone structure of the mandibular support cannot be used as a guide to the shape of the arch form during orthodontic treatment.

Evaluation of arch width variations among different skeletal patterns in South Indian population

Background:

Anterior cranial base can be taken as a reference line (SN) to determine the steepness of mandibular plane. Subjects with high mandibular plane angle tend to have a long face and one with low MP-SN angle has a shorter face.

Objective:

This study was done to investigate if dental arch widths correlated with vertical facial types and if there are any differences in arch widths between untreated male and female adults in South Indian population.

Materials and Methods:

Lateral cephalogram and dental casts were obtained from 180 untreated South Indian adults (90 males and 90 females) above 18 year old with no cross bite, minimal crowding and spacing. The angle between the anterior cranial base and the mandibular plane was measured on lateral cephalogram of each patient. Dental casts were used to obtain comprehensive dental measurements including maxillary and mandibular inter canine, inter premolar and inter molar widths, as well as amount of crowding or spacing.

Results:

The results showed that male arch widths were significantly larger than those of females (P < 0.05) and there was a significant decrease in inter arch width as the MP-SN angle increased in untreated adult South Indian population. The results obtained in our study when compared with studies done in other population groups showed that there is difference in inter arch widths according to ethnicity and race.

Conclusion:

It was concluded that the dental arch width is associated with gender, race and vertical facial morphology. Thus using individualized arch wires according to each patient's pre treatment arch form and width is suggested during orthodontic treatment.