Immobilization of cellulose extracted from Robinia Pseudoacacia seed fibers onto chitosan: Chemical characterization and study of methylene blue removal

Effective decontamination of methylene blue from aqueous solutions using novel nano-magnetic biochar from green pea peels

The conversion of agricultural waste into high-value carbon products has been an attractive area in waste management strategy. This study highlighted the synthesis and effectiveness of green pea peels (GPP), green pea biochar (GPBC), and nano-ferromagnetic green pea biochar (NFGPBC) by the ferrous/ferric co-precipitation synthesis method for eliminating cationic dyes molecules from solutions. The morphological, physicochemical, and structural properties of GPP, GPBC, and NFGPBC were approved by Scanning Electron Microscopy (SEM), Transmission Emission Microscopy (TEM), Energy Dispersive X-ray (EDX), Bruneau Emmett Teller (BET), Fourier Transform Infrared spectroscopy (FTIR), and X-ray Diffraction (XRD) techniques. Vibrating Sample Magnetometry (VSM) analysis confirmed the NFGPBC magnetization performance. The capacity of each adsorbent for methylene blue removal was evaluated at various parameters of material dosage (50-250 mg/150 mL), pH (2-12), initial concentration (50-250 mg/L), contact time (0-90 min) and temperature (20-60 °C). The three developed adsorbent materials GPP, GPBC, and NFGPBC, possessed reasonable BET surface areas of 0.6836, 372.54, and 147.88 m2g-1, and the corresponding monolayer adsorption capacities of 163.93, 217.40, and 175.44 mg/g, respectively. The superior performances of GPBC and NFGPBC were due to their increased surface area compared with the parent green pea peels (GPP). The results from adsorption kinetics studies of all prepared materials were pseudo-second-order and Elovich kinetics models. The thermodynamic parameters exhibited MB sorption's favorability, spontaneity, and endothermic nature. The NFGPBC material experienced Vander Waal forces, electrostatic interaction, hydrogen bonding, and hydrophobic interactions as predominant modes of the solid-liquid interaction. The regeneration, recycling, and reusability of the synthesized GPP, GPBC, and NFGPBC performed at five adsorption cycles revealed that NFGPBC demonstrated excellent cyclical performances attaining a minimum 8.9% loss in capacity due to paramagnetic properties. Thus, NFGPBC is a green, efficient, and eco-friendly material recommended for large-scale production and application in wastewater.

Synthesis, Characterization, and Application of Dichloride (5,10,15,20-Tetraphenylporphyrinato) Antimony Functionalized Pectin Biopolymer to Methylene Blue Adsorption

In this work, pectin biopolymers were functionalized with dichloride (5,10,15,20-tetraphenylporphyrinato) antimony [Sb(TPP)Cl₂] at various compositions (0.5%, 1%, and 2%). The prepared compounds were characterized with several analytical methods, including X-ray fluorescence (XRF) spectrometry, Fourier-transform infrared spectroscopy (FT-IR), electrospray ionization mass spectrometry (EIS), scanning electron microscope (SEM), X-ray diffraction (XRD), and thermogravimetric-differential thermal (TGA/DTG) analysis. The XRF technique evidenced the presence of Sb metal in the composite beads. FT-IR suggested that the interaction between pectin and the [Sb(TPP)Cl₂] complex was assured by inter- and intramolecular C-H⋯O, C-H⋯Cl hydrogen bonds and weak C-H⋯Cg π interactions (Cg is the centroid of the pyrrole and phenyl rings). The morphological features of the prepared polymeric beads were affected by the addition of [Sb(TPP)Cl₂] particles, and the surface became rough. The thermal residual mass for the composite beads (29%) was more important than that of plain beads (23%), which confirmed the presence of inorganic matter in the modified polymeric beads. At 20 °C, the highest adsorption amounts of methylene blue were 39 mg/g and 68 mg/g for unmodified pectin and pectin-[Sb(TPP)Cl₂] beads, respectively. The adsorption mechanism correlated well with the kinetic equation of the second order and the isotherm of Freundlich. The prepared polymeric beads were characterized as moderate-to-good adsorbents. The calculated thermodynamic parameters demonstrated an exothermic and thermodynamically nonspontaneous mechanism.

Removing methylene blue from water: A study of sorption effectiveness onto nanoparticles-doped activated carbon

In this present study, silver (Ag) and titanium dioxide (TiO₂) nanoparticles were successfully deposited on coconut shell-derived activated carbon (CSAC), to synthesize a novel nanocomposite (CSAC@AgNPs@TiO₂NPs) for the adsorption of Methylene Blue (MB) dye from aqueous solution. The fabricated CSAC@AgNPs@TiO₂NPs nanocomposite was analyzed by Scanning Electron Microscope (SEM), X-ray Diffraction (XRD), Fourier-Transform Infrared Spectroscopy (FTIR), Transmission Electron Microscope (TEM) equipped with Energy Dispersive X-ray spectroscopy (EDS) detector, X-ray Photoelectron Spectroscope (XPS), and Brunauer-Emmett-Teller (BET). The successful deposition of AgNPs and TiO₂NPs on CSAC surface was revealed by the TEM/EDX, SEM, and XPS analysis. The mesopore structure of CSAC@AgNPs@TiO₂NPs has a BET surface area of 301 m²/g. The batch adsorption studies were conducted and the influence of different parameters, i.e., adsorbent dose, adsorption time, initial dye concentration, pH and temperature were investigated. The nonlinear isotherm and kinetic modelling demonstrated that adsorption data were best fitted by Sips isotherm and pseudo-second-order models, respectively. The maximum adsorption capacity of MB onto CSAC@AgNPs@TiO₂NPs by the Sips model was 184 mg/g. Thermodynamic results revealed that the adsorption was endothermic, spontaneous and physical in nature. CSAC@AgNPs@TiO₂NPs revealed that MB absorption by CSAC@AgNPs@TiO₂NPs was spontaneous and endothermic. The uptake capacity of MB was influenced significantly by the presence of competing ions including, NO₃^-, HCO_3, Ca²⁺, and Na⁺. Repeated tests indicated that the CSAC@AgNPs@TiO₂NPs can be regenerated and reused six times before being discarded. The primary separation mechanism between MB dye and CSAC@AgNPs@TiO₂NPs was the electrostatic interaction. Thus, CSAC@AgNPs@TiO₂NPs was an outstanding material, which displayed good applicability in real water with ≥ 97% removal of MB dye.

Cellulose-based hydrogel for adsorptive removal of cationic dyes from aqueous solution: isotherms and kinetics

The development of economic and recyclable adsorbents for removing pollutants from contaminated water is gaining increasing attention. Agro residue or nature-based material sourced absorbents could revolutionize the future of wastewater treatment. Hence in this study, nanocellulose was synthesized from coconut husk fiber and immobilized onto chitosan to form hydrogel beads. The BET surface area and zeta potential of the adsorbent nanocrystalline cellulose-chitosan hydrogel (NCC-CH) bead was 25.77 m² g^-1 and +50.6 mV, respectively. The functional group analysis also confirmed that the adsorbent had functional groups appropriate for the adsorption of textile dyes. The adsorption performance of NCC-CH and also the influence of initial dye concentration, adsorbent dose, pH, and contact time was evaluated by batch adsorption studies with crystal violet (CV) and methylene blue (MB) dyes. The most favorable operational conditions achieved through I-optimal design in response surface methodology were 0.5 g NCC-CH, 1 h, 9 pH, and 60 mg L^-1 for CV removal (94.75%) and 0.13 g NCC-CH, 1 h, 9 pH, and 30 mg L^-1 for MB removal (95.88%). The polynomial quadratic model fits the experimental data with an R ² value of 0.99 and 0.98 for CV and MB removal, respectively. The optimum depiction of the isotherm data was obtained using the Freundlich model for MB adsorption and Freundlich and Langmuir model for CV adsorption. The Dubinin-Radushkevich (D-R) isotherm was also a good fit to the adsorption of CV and MB dye, suggesting the physisorption due to its free energy of adsorption < 8 kJ mol^-1. The kinetics were effectively explained by a pseudo-second order model for both the dyes suggesting that chemical mechanisms influenced the adsorption of CV and MB dyes onto NCC-CH. The intraparticle diffusion model best suited the MB adsorption with three stages rather than the CV with a single step process. Also, the removal efficiency of adsorbent was retained at above 60% even after seven adsorption-desorption cycles indicating the effectiveness of the NCC-CH hydrogel beads for the removal of textile dyes.