The relationship between increased hip range of motion, wear, and locking mechanism failure in the Harris-Galante acetabular component

The incidence of dissociated liners in 4,751 consecutive total hip arthroplasties using Pinnacle polyethylene acetabular liners

INTRODUCTION

Acetabular liner dissociation is a complication exclusive to modular designs. We present a single surgeon series of 8 polyethylene liner dissociations with the Pinnacle Acetabular System (DePuy Orthopaedics) from over 4,750 cases. We also present a review of the literature and data from the UK National Joint Registry (NJR) on dissociation in total hip arthroplasty (THA).

METHODS

The Pinnacle Acetabular System has been used exclusively by the senior author since April 2003, and to date 5,882 have been implanted (837 ceramic liners, 4,751 polyethylene liners (1,606 Enduron/3,145 Marathon) and 294 metal liners). We reviewed all cases of liner dissociation from this cohort to determine an overall incidence with polyethylene liners, identify associated risk factors, and report the outcome following revision surgery.

RESULTS

Our incidence of this complication is 8 out of 4,751 cases (0.17%). Review of these cases and the literature suggests that femoral neck impingement against the polyethylene liner and/or edge loading may produce fatigue failure of the locking mechanism and subsequent dissociation.

CONCLUSIONS

Ensuring correct liner seating/locking, minimising impingement, achieving appropriate component version and avoiding radiographic cup inclinations >50° should minimise the risk of liner dissociation. Any new noise or squeaking from a polyethylene liner should undergo radiographic investigation to exclude dissociation. We recommend managing late cases of liner dissociation with revision of the acetabular shell if the cup orientation could be improved or if there is any damage to the liner-locking groove, to reduce the risk of recurrence.

Retrieval analysis of new-generation yttria-stabilized zirconia femoral heads after total hip arthroplasty

Zirconia femoral heads were introduced for total hip arthroplasty (THA) with the expectation of lower polyethylene (PE) wear and better clinical results. Because several studies reported poor survivorship of yttria-stabilized zirconia-PE THA, we investigated a new-generation yttria-stabilized zirconia head (diameter, 26 mm) manufactured by NGK Spark Plug. We retrieved six zirconia heads at revision THA after they had been in place for a mean of 8.6 years and measured their surface roughness and mean monoclinic content. Although their mean monoclinic content was higher than that of the unused head, surface roughness in the implanted heads was as low as that of the unused head, indicating that wear reduction may be possible with the selection of a suitable zirconia femoral head.

Case report: Painless chronic liner dissociation of a total hip arthroplasty

BACKGROUND

Dislocation or liner dissociation of a total hip prosthesis usually results in pain and discomfort. Although several reports describe chronic dislocation and its treatment, chronic liner dissociation is an unreported complication.

CASE DESCRIPTION

We report an unrecognized dissociation and displacement of the liner of a total hip prosthesis after revision THA. The patient had virtually no pain or functional restrictions. The patient's only complaint was pain on the contralateral side, associated with a leg-length discrepancy. Since the patient had no complaints relative to the liner dissociation we elected not to pursue further treatment. The contralateral pain was treated successfully with a shoe lift.

LITERATURE REVIEW

Chronic dislocation of a THA is a rare complication and we found reports of only seven cases in the literature. We found no reports of chronic liner dissociation.

CLINICAL RELEVANCE

Orthopaedic surgeons should be aware of the possibility of this rare complication. Our case and the literature suggest treatment can be nonsurgical or surgical.

Retrieval analysis of Harris-Galante I and II acetabular liners in situ for more than 10 years

BACKGROUND AND PURPOSE

There have been few reports documenting the wear and oxidation performance of the polyethylene bearing surface of HGPI and HGPII THA devices. We evaluated retrieved HGPI and HGPII acetabular liners that had been in situ for more than 10 years and determined whether there was a relationship between clinical and radiographic factors, surface damage, wear, and oxidation.

MATERIALS AND METHODS

129 HGPI and II acetabular liners with implantation times of > 10 years were retrieved at 4 institutions between 1997 and 2010. The liners were made from a single resin and were gamma radiation-sterilized in air. Surface damage, linear wear, and oxidation index (OI) were assessed. Differences in clinical and radiographic factors, surface damage, linear wear, and OI for the 2 designs were statistically evaluated separately and together.

RESULTS

Articular surface damage and backside damage was similar in the 2 designs. The linear penetration rate was 0.14 (SD 0.07) mm/year for the HGPI liners and 0.12 (SD 0.08) mm/year for the HGPII liners. For both cohorts, the rim had a higher OI than the articular surface. 74% of the liners had subsurface cracking and 24% had a complete fracture through the acetabular rim.

INTERPRETATION

Despite modification of the HGP locking mechanism in the HGPII design, dissociation of the liner from the acetabular shell can still occur if fracture of the rim of the liner develops due to oxidative degradation.

Bony impingement limits design-related increases in hip range of motion

BACKGROUND

Factors affecting risk for impingement and dislocation can be related to the patient, implant design, or surgeon. While these have been studied independently, the impact of each factor relative to the others is not known.

QUESTIONS/PURPOSES

We determined the effect of three implant design factors, prosthetic placement, and patient anatomy on subject-specific ROM.

METHODS

We virtually implanted hip geometry obtained from 16 CT scans using computer models of hip components with differences in head size, neck diameter, and neck-shaft angle. A contact detection model computed ROM before prosthetic or bony impingement. We correlated anatomic measurements from pelvic radiographs with ROM.

RESULTS

When we implanted the components for best fit to the subject's anatomy or in the recommended orientation of 45° abduction and 20° anteversion, ROM was greater than 110° of flexion, 30° of extension, 45° of adduction-abduction, and 40° of external rotation. Changes in head size, neck diameter, and neck-shaft angle generated small gains (3.6°-6°) in ROM when analyzed individually, but collectively, we noted a more substantial increase (10°-17°). Radiographic measurements correlated only moderately with hip flexion and abduction.

CONCLUSIONS

It is feasible to tailor implant placement to each patient to maximize bony coverage without compromising ROM. Once bony impingement becomes the restricting factor, further changes in implant design may not improve ROM. Radiographic measurements do not appear to have value in predicting ROM.

Range of motion of large head total hip arthroplasty is greater than 28 mm total hip arthroplasty or hip resurfacing

BACKGROUND

Reduced range of motion of the hip has a detrimental influence on lower limb function. Large diameter head total hip arthroplasty may theoretically have a greater potential for restoring normal hip range of motion due to greater head-neck diameter ratio, and hence provide better function compared to conventional or hip resurfacing arthroplasty.

METHOD

At minimum one year follow-up, range of motion of the operated and contra lateral hips was clinically assessed using digital photographs and bony landmarks in a clinical comparative study. We assessed if 1) large diameter head total hip arthroplasty (55 patients) restores better hip range of motion compared to 28 mm total hip arthroplasty (50 patients) or hip resurfacing (60 patients) 2) large diameter head total hip arthroplasty achieves same hip range of motion as contra lateral normal hips and 3) hip range of motion correlates with the WOMAC score.

FINDINGS

The large diameter head total hip arthroplasty group had significantly greater total arcs of motion (approximately 20°), mostly due to an increase of hip flexion and external rotation, but did not reach normal hip motion. The hip range of motion showed significant correlation with the WOMAC score, especially the flexion arc.

INTERPRETATION

The better hip range of motion of large diameter head total hip arthroplasty is likely due to the greater head to neck diameter ratio and hence seems to be the best option to optimize range of hip motion and improve function after hip arthroplasty.

Survivorship of polyethylene liner exchanges performed for the treatment of wear and osteolysis among porous-coated cups

For the past 17 years, we have favored treating patients with polyethylene wear and osteolysis by performing a liner exchange with retention of the old shell when possible. Using our institutional database, we identified 187 acetabular revisions in which we had retained the old shell. Among this group, we found 25 rerevisions. These included 10 for hip instability, 9 for cup loosening, 3 for recurrence of excessive wear or osteolysis, 2 for infection, and 1 for dissociation of the replaced liner. The need for rerevision varied with the different retained shell designs. We rerevised 17% of the total hip arthroplasties with old spiked shells, 21% with Arthropor shells, 13% with Triloc shells and 5% with Duraloc shells. Before making a decision to retain or remove a well-fixed old acetabular shell, we recommend consideration of the design's past track record and careful inspection of the condition of the existing shell.