Anodic behavior of clioquinol at a glassy carbon electrode

First voltammetric analysis of two possible anticancer drug candidates using an unmodified glassy carbon electrode

Dimethyl 2-[2-(1-phenyl-4,5-dihydro-1H-imidazol-2-yl)hydrazinylidene]butanedioate (DIHB) and 8-(3-chlorophenyl)-2,6,7,8-tetrahydroimidazo[2,1-c][1,2,4]triazine-3,4-dione (HDIT) are promising candidates for anticancer agents, the first analytical procedures of which are presented in this paper. The commercially available unmodified glassy carbon electrode (GCE) was used as a sensor for the individual and simultaneous differential pulse voltammetric (DPV) determination of these possible anticancer drugs. The findings concerning the electrochemical behaviour indicated that DIHB and HDIT display at GCE, as a sensor, the oxidation peaks at 1.18 and 0.98 V, respectively (vs. Ag/AgCl, 3.0 mol L-1 KCl) in the 0.125 mol L-1 acetate buffer of pH = 4.5, which were employed for their quantification. Various experimental parameters were carefully investigated, to achieve high sensitivity in voltammetric measurements. Finally, under the optimised conditions (t of 60 s, ΔEA of 75 mV, ν of 225 mV s-1, and tm of 2 ms), the proposed DPV procedure with the GCE demonstrated broad linear sensing ranges (1-200 nmol L-1-DIHB and 5-200 nmol L-1-HDIT), boasting the detection limits of 0.18 nmol L-1 for DIHB and 1.1 nmol L-1 for HDIT. Moreover, the developed procedure was distinguished by good selectivity, repeatability of DIHB and HDIT signals and sensor reproducibility. The practical application of this method was demonstrated by analysing the urine reference material without any prior treatment. The results showed that this environmentally friendly approach, with a modification-free sensor, is suitable for the sensitive, selective and rapid quantification of DIHB and HDIT.

Electroanalytical analysis of phenol oxidation using bacteria immobilized by a polycaprolactone coating on the copper electrode surface

The copper electrode modified by bacteria immobilised by a polycaprolactone film was successfully developed by electropolymerisation for the purpose of determining the presence of phenol. Electrochemical techniques such as square-wave voltammetry (SWV), cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) were used to characterize the electrochemical properties of the Cu-polymer/bacteria electrode. The results show that the intensity of the phenol oxidation peak increases with concentration, allowing us to obtain good analytical results with DL of 2.156 × 10-7 M and QL which is 7.2 × 10-7 M , confirming that the biosensor has excellent electroanalytical activity for phenol oxidation, with good stability and a wide linear range. Our electrode is based on a easily available and inexpensive material, as well as on its simple preparation, which has demonstrated high performance for phenol.

An Electrochemical Screen-Printed Sensor Based on Gold-Nanoparticle-Decorated Reduced Graphene Oxide-Carbon Nanotubes Composites for the Determination of 17-β Estradiol

In this study, a screen-printed electrode (SPE) modified with gold-nanoparticle-decorated reduced graphene oxide-carbon nanotubes (rGO-AuNPs/CNT/SPE) was used for the determination of estradiol (E2). The AuNPs were produced through an eco-friendly method utilising plant extract, eliminating the need for severe chemicals, and remove the requirements of sophisticated fabrication methods and tedious procedures. In addition, rGO-AuNP serves as a dispersant for the CNT to improve the dispersion stability of CNTs. The composite material, rGO-AuNPs/CNT, underwent characterisation through scanning electron microscopy (SEM), ultraviolet-visible absorption spectroscopy (UV-vis), Fourier-transform infrared (FTIR) spectroscopy, and atomic force microscopy (AFM). The electrochemical performance of the modified SPE for estradiol oxidation was characterised using cyclic voltammetry (CV) and differential pulse voltammetry (DPV) techniques. The rGO-AuNPs/CNT/SPE exhibited a notable improvement compared to bare/SPE and GO-CNT/SPE, as evidenced by the relative peak currents. Additionally, we employed a baseline correction algorithm to accurately adjust the sensor response while eliminating extraneous background components that are typically present in voltammetric experiments. The optimised estradiol sensor offers linear sensitivity from 0.05-1.00 µM, with a detection limit of 3 nM based on three times the standard deviation (3δ). Notably, this sensing approach yields stable, repeatable, and reproducible outcomes. Assessment of drinking water samples indicated an average recovery rate of 97.5% for samples enriched with E2 at concentrations as low as 0.5 µM%, accompanied by only a modest coefficient of variation (%CV) value of 2.7%.

Recent advances in Ponceau dyes monitoring as food colorant substances by electrochemical sensors and developed procedures for their removal from real samples

Ponceau dyes are one of the food coloring materials that are added to various pharmaceutical, health and food products and give them an appearance. These dyes contain contaminants such as Benzidine, 4-Aminobiphenyl, and 4-Aminoazobenzene that are safe in small amounts, but they are not approved by the US Food and Drug Administration (US-FDA) for human consumption. This study comprehensively was reviewed the properties, applications, chemistry, and toxicity of Ponceau dyes as food colorant substances. Electroanalysis of Ponceau dyes was discussed in detail, and the various electrochemical sensors used to detect and monitor these dyes as food colorant were examined. The applied methods of removing and degradation of these dyes in municipal and industrial wastes were also discussed. Conclusions and future perspectives to motivate future research were also explored.

Surface engineering of gadolinium oxide nanoseeds with nitrogen-doped carbon quantum dots: an efficient nanocomposite for precise detection of antibiotic drug clioquinol

Nitrogen-doped carbon quantum dot decorated gadolinium oxide nanoseeds as an electrode modifier for the sensitive electrochemical detection of the antibiotic drug clioquinol in urine samples.

Voltammetric analysis of nitroxoline in tablets and human serum using modified carbon paste electrodes incorporating mesoporous carbon or multiwalled carbon nanotubes

Mesoporous carbon (MC) was synthesized using mesoporous SiO₂ template material (SBA-15) and sucrose as the carbon source. SBA-15, MC and multi-walled carbon nanotubes (MWCNTs) were used as sensors for determination of nitroxoline drug.