Thermogravimetric pyrolysis of onion skins: Determination of kinetic and thermodynamic parameters for devolatilization stages using the combinations of isoconversional and master plot methods

Pyrolysis of municipal solid waste compost: Pilot plant evaluation as a sustainable practise of waste management

To evaluate the potential of compost based on municipal solid waste (MSW) and 20% legume pruning under a pyrolysis process, generated products, including solids (biochar), liquids (bio-oil), and gases (non-condensable gases), through experimentation in a pilot plant with a fluidized bed reactor at 450°C and gas chromatography/mass spectrometry have been analysed. In addition, the compost kinetic behaviour by thermogravimetric analysis (TGA), using the Flynn-Wall-Ozawa (FWO) method, has been investigated. Four different reaction zones, associated with lignocellulosic materials (hemicellulose, cellulose, and lignin) with a first step for water evaporation, in TGA curve have been observed. A biochar with low stability and aromaticity, considering high and low O/C and H/C ratios, respectively, has been obtained. The obtained pyrolytic liquids contain a high concentration of phenolic compounds because of a significant presence of lignins and other high molecular weight compounds in the original material. Moreover, the generated non-condensable gases consist mainly of short-chain compounds, such as alcohols, aldehydes, and alkenes produced from hemicellulose, cellulose, and proteins.

Co-pyrolysis of biomass and polyethylene: Insights into characteristics, kinetic and evolution paths of the reaction process

Investigation on the distribution and mechanism of co-pyrolysis products is vital to the directional control and high-value utilization of agriculture solid wastes. Co-pyrolysis, devolatilization, kinetics characteristics, and evolution paths of corn stalk (CS) and low-density-polyethylene (LDPE) were investigated via thermogravimetric experiments. The co-pyrolysis behaviors could be separated into two stages: firstly, the degradation of CS (150- 400 °C); secondly, the degradation of CS (400- 550 °C). The devolatilization index (DI) increased with the addition of LDPE. Furthermore, a combination of devolatilization chemical analysis with product analysis to analyze the intrinsic mechanism during co-pyrolysis. The results indicated that the yield of alkanes and olefin in gas products increased with the addition of LDPE. Additionally, LDPE pyrolysis maybe abstract hydrogen from CS pyrolysis and evolved into hydrogen, methane, and ethylene. Further, the co-pyrolysis kinetic parameters were computed by using model-free isoconversion methods, which showed promotion of CS pyrolysis and the reduced activation energy. All the activation energy were declined, which indicated a "bidirectional positive effect" during co-pyrolysis. The mean activation energy of P-cellulose (P-CE), P-hemicellulose (P-HM), P-lignin (P-LG), and LDPE decreased by 23.49 %, 12.89 %, 15.36 %, and 27.82 %, respectively. This study further proves the hydrogen donor transfer pathway in the co-pyrolysis process of CS and LDPE, providing theoretical support for the resource utilization of agricultural solid waste.

Self-Supported Biopolymeric Films Based on Onion Bulb (Allium cepa L.): Gamma-Radiation Effects in Sterilizing Doses

Sterilization is a fundamental step to eliminate microorganisms prior to the application of products, especially in the food and medical industries. γ-irradiation is one of the most recommended and effective methods used for sterilization, but its effect on the properties and performance of bio-based polymers is negligible. This work is aimed at evaluating the influence of γ-radiation at doses of 5, 10, 15, 25, 30, and 40 kGy on the morphology, properties, and performance of bioplastic produced from onion bulb (Allium cepa L.), using two hydrothermal synthesis procedures. These procedures differ in whether the product is washed or not after bioplastic synthesis, and are referred to as the unwashed hydrothermally treated pulp (HTP) and washed hydrothermally treated pulp (W-HTP). The morphological analysis indicated that the film surfaces became progressively rougher and more irregular for doses above 25 kGy, which increases their hydrophobicity, especially for the W-HTP samples. In addition, the FTIR and XRD results indicated that irradiation changed the structural and chemical groups of the samples. There was an increase in the crystallinity index and a predominance of the interaction of radiation with the hydroxyl groups-more susceptible to the oxidative effect-besides the cleavage of chemical bonds depending on the γ-radiation dose. The presence of soluble carbohydrates influenced the mechanical behavior of the samples, in which HTP is more ductile than W-HTP, but γ-radiation did not cause a change in mechanical properties proportionally to the dose. For W-HTP, films there was no mutagenicity or cytotoxicity-even after γ-irradiation at higher doses. In conclusion, the properties of onion-based films varied significantly with the γ-radiation dose. The films were also affected differently by radiation, depending on their chemical composition and the change induced by washing, which influences their use in food packaging or biomedical devices.

Onion waste based-biorefinery for sustainable generation of value-added products

Waste derived from the onion processing sector can be harnessed for the production of organic acids, polyphenols, polysachharides, biofuels and pigments. To sustainably utilize onion processing residues, different biorefinery strategies such as enzymatic hydrolysis, fermentation and hydrothermal carbonization have been widely investigated. This review discusses the recent advances in the biorefinery approaches used for valorization of onion processing waste followed by the production of different value-added products from diverse classes of onion waste. The review also highlights the current challenges faced by the bioprocessing sector for the utilization of onion processing waste and perspectives to tackle them.

Effect of Cd on Pyrolysis Velocity and Deoxygenation Characteristics of Rice Straw: Analogized with Cd-Impregnated Representative Biomass Components

The pyrolysis characteristics of cadmium (Cd)-impregnated cellulose, hemicellulose, and lignin were studied to elucidate the pyrolysis velocity and deoxygenation characteristics of Cd-contaminated rice straw. The results show that Cd significantly affects the pyrolysis characteristics of a single biomass component. With a heating rate of 5 °C·min−1 and a Cd loading of 5%, the initial pyrolysis temperature of cellulose and hemicellulose decreases while that of lignin increases. The maximum pyrolysis velocity of cellulose, hemicellulose, and lignin is decreased by 36.6%, 12.4%, and 15.2%, respectively. Cd increases the pyrolysis activation energy of the three components and inhibits their deoxygenation. For the pyrolysis of Cd-contaminated rice straw, both the initial depolymerization temperature and the pyrolysis velocity of hemicellulose is reduced, while the pyrolysis velocity of cellulose is accordingly increased. When Cd loading amplifies to 0.1%, 1%, and 5%, the maximum pyrolysis velocity of hemicellulose is decreased by 7.2%, 10.5%, and 21.3%, while that of cellulose is increased by 8.4%, 62.1%, and 97.3%, respectively. Cd reduces the release of volatiles and gas from rice straw, such as CO2, CO, and oxygen-containing organics, which retains more oxygen and components in the solid fraction. This research suggested that Cd retards the pyrolysis velocity and deoxygenation of rice straw, being therefore beneficial to obtaining more biochar.