Anaerobic-aerobic treatment of high-strength and recalcitrant textile dyeing effluents

Continuous ultrasonic ozone coupling technology-assisted control of ceramic membrane fouling coupled enhanced multiphase mixing to treat dye wastewater and CFD flow field simulation

In this study, ozone catalysts (hydrogenation-modified red mud, HM-RM) successfully prepared by hydrogenation-modification of industrial hazardous solid waste red mud (RM) as a raw material in accordance with the viewpoint of treating waste with waste and using waste. Meanwhile, as for the common phenomenon of membrane fouling, uneven distribution of multiphase solid catalysts and ozone in liquids, the addition of ultrasound can not only disperse materials, but also play a role in online cleaning of ceramic membranes and catalysts. The optimum treatment conditions for Rhodamine B (RhB) solution with volume of 2 L and concentration of 40 mg/L were catalyst concentration of 0.4 mg/L, reaction temperature of 45 °C, ultrasonic time of 1 h, ultrasonic intensity of 600 W, removal rate of RhB was up to 90 %. In addition, the computational fluid dynamics (CFD) simulation method was used to investigate the fluid flow between the two gas-liquid phases and the effect of the negative pressure of the membrane pump on the fluid by the analysis of flow, pressure and ozone flux of the ceramic membrane(CM) reaction apparatus. The CFD simulation results showed that at the inlet gas-liquid flow rate of 3 m/s and the negative pressure of 20,000 Pa, the maximum flow rates of CM-1 were 3 m/s, 0.752 m/s for CM-2, and 0.228 m/s for CM-3, respectively. Vortices, which are beneficial to solid-liquid mixing and gas-liquid mass transfer, formed between the suction port CM-1 of CM-1 and the inlets of CM-2 and CM-3. This discovery is consistent with relevant experimental research results. Significantly higher concentrations of both •OH and dissolved ozone were observed in the US/HM-RM/O3 system compared to other systems, indicating the significant improvement in ozone utilization rate through the application of ultrasound. The superiority of the US/HM-RM/O3 device was demonstrated. The real dye effluent was tested under optimum operating conditions and the results showed that COD and TOC were reduced by 81.34 % and 60.23 % respectively after 180 min of treatment. The above research can provide technical support for the treatment of dye wastewater using Ultrasound-enhanced ozone oxidation ceramic membranes.

Advances from conventional to biochar enhanced biotreatment of dyeing wastewater: A critical review

DW (Dyeing wastewater) contains a large amount of dye organic compounds. A considerable proportion of dye itself or its intermediate products generated during wastewater treatment process exhibits CMR (Carcinogenic/Mutagenic/Toxic to Reproduction) toxicity. Compared with physicochemical methods, biological treatment is advantageous in terms of operating costs and greenhouse gas emissions, and has become the indispensable mainstream technology for DW treatment. This article reviews the adsorption and degradation mechanisms of dye organic compounds in wastewater and analyzed different biological processes, ranging from traditional methods to processes enhanced by biochar (BC). For traditional biological processes, microbial characteristics and communities were discussed, as well as the removal efficiency of different bioreactors. BC has adsorption and redox electron mediated effects, and coupling with biological treatment can further enhance the process of biosorption and degradation. Although BC coupled biological treatment shows promising dye removal, further research is still needed to optimize the treatment process, especially in terms of technical and economic competitiveness.

Fabrication of titania/calcium alginate nanocomposite matrix for efficient adsorption and photocatalytic degradation of malachite green

This work aims to examine the two techniques' efficiency for the elimination of malachite green (MG) by photocatalytic degradation and adsorption onto synthesized solid nanomaterials. Three solid samples were prepared as calcium alginate (AG), nanotitania (NT), and nanotitania/calcium alginate composite (TG). The morphological and physicochemical characteristics of the solid nanomaterials were investigated by XRD, TGA, DRS, FTIR, pHPZC, nitrogen adsorption/desorption isotherm, SEM, and TEM. The main experimental conditions were determined for sample dose, shaking time, pH, initial malachite green concentration, temperature, ionic strength, and UV lamp power. The resulting data proved that TG attained the higher adsorption capacity (252.52 mg/g) at 40 °C. The adsorption of MG was well fitted by Langmuir, Temkin, Dubinin-Radushkevich, pseudo-second order, intra-particle diffusion, and Elovich models onto all the prepared samples, confirming the endothermic, spontaneous, and favorable adsorption process. The maximum degradation percent (99.6 %) of MG was achieved by using 1.0 g/L as a catalyst dose, 10 mg/L of initial MG concentration, and 33 W for TG. The photodegradation of MG was well fitted by Eyring-Polanyi and Arrhenius models onto the surface of catalyst. The TG reusability resulted in a decrease in the degradation efficiency by 9.8 %, indicating its great capacity as the first nanotitania/calcium alginate nanocomposite used in removing MG from wastewater by two technologies in the same article.

Electrochemical Characterization Using Biosensors with the Coagulant Moringa oleifera Seed Lectin (cMoL)

Triturated Moringa oleifera seeds have components that adsorb recalcitrant indigo carmine dye. Coagulating proteins known as lectins (carbohydrate-binding proteins) have already been purified from the powder of these seeds, in milligram amounts. The coagulant lectin from M. oleifera seeds (cMoL) was characterized by potentiometry and scanning electron microscopy (SEM) using MOFs, or metal-organic frameworks, of [Cu₃(BTC)₂(H₂O)₃]_n to immobilize cMoL and construct biosensors. The potentiometric biosensor revealed an increase in the electrochemical potential resulting from the Pt/MOF/cMoL interaction with different concentrations of galactose in the electrolytic medium. The developed aluminum batteries constructed with recycled cans degraded an indigo carmine dye solution; the oxide reduction reactions of the batteries generated Al(OH)₃, promoting dye electrocoagulation. Biosensors were used to investigate cMoL interactions with a specific galactose concentration and monitored residual dye. SEM revealed the components of the electrode assembly steps. Cyclic voltammetry showed differentiated redox peaks related to dye residue quantification by cMoL. Electrochemical systems were used to evaluate cMoL interactions with galactose ligands and efficiently degraded dye. Biosensors could be used for lectin characterization and monitoring dye residues in environmental effluents of the textile industry.