A shriveled rectangular carbon tube with the concave surface for high-performance enzymatic glucose/O2 biofuel cells

A wearable and flexible lactic-acid/O2 biofuel cell with an enhanced air-breathing biocathode

The performance of biocathode in an enzymatic biofuel cell (EBFC) in the real application is somehow overlooked. Herein, a wearable and flexible lactic-acid/O2 EBFC enhanced with an air-breathing biocathode is designed to solve the limitation of biocathode that arises from the low solubility and slow mass transfer of the dissolved oxygen. To improve the oxygen supply efficiency for the air-breathing biocathode, a superhydrophobic base electrode creating an efficient air-solid-liquid triphase interface is developed. The designed EBFC with an 'island-bridge' configuration is integrated by assembling the current collectors of air-breathing biocathode and bioanode on a commercial laminating film (LF) screen-printed with a noninterfering circuit. It is found that the biocathode/bioanode area ratio should exceed 9:1 so that the designed EBFC (1A//9C) can achieve the optimal performance. This EBFC delivers an open circuit voltage of ca. 0.75 V and outputs a maximum power density of ca. 1.78 mW cm-2. In addition, a scaled-up EBFC (total bioanode area: 1.5 cm2) successfully powers a self-developed low-power device of heartrate in the pulse operation mode when applied on a volunteer's arm.

Research Progress in Enzyme Biofuel Cells Modified Using Nanomaterials and Their Implementation as Self-Powered Sensors

Enzyme biofuel cells (EBFCs) can convert chemical or biochemical energy in fuel into electrical energy, and therefore have received widespread attention. EBFCs have advantages that traditional fuel cells cannot match, such as a wide range of fuel sources, environmental friendliness, and mild reaction conditions. At present, research on EBFCs mainly focuses on two aspects: one is the use of nanomaterials with excellent properties to construct high-performance EBFCs, and the other is self-powered sensors based on EBFCs. This article reviews the applied nanomaterials based on the working principle of EBFCs, analyzes the design ideas of self-powered sensors based on enzyme biofuel cells, and looks forward to their future research directions and application prospects. This article also points out the key properties of nanomaterials in EBFCs, such as electronic conductivity, biocompatibility, and catalytic activity. And the research on EBFCs is classified according to different research goals, such as improving battery efficiency, expanding the fuel range, and achieving self-powered sensors.

Conductive Polymers and Their Nanocomposites: Application Features in Biosensors and Biofuel Cells

Conductive polymers and their composites are excellent materials for coupling biological materials and electrodes in bioelectrochemical systems. It is assumed that their relevance and introduction to the field of bioelectrochemical devices will only grow due to their tunable conductivity, easy modification, and biocompatibility. This review analyzes the main trends and trends in the development of the methodology for the application of conductive polymers and their use in biosensors and biofuel elements, as well as describes their future prospects. Approaches to the synthesis of such materials and the peculiarities of obtaining their nanocomposites are presented. Special emphasis is placed on the features of the interfaces of such materials with biological objects.

A miniaturized bionic ocean-battery mimicking the structure of marine microbial ecosystems

Marine microbial ecosystems can be viewed as a huge ocean-battery charged by solar energy. It provides a model for fabricating bio-solar cell, a bioelectrochemical system that converts light into electricity. Here, we fabricate a bio-solar cell consisting of a four-species microbial community by mimicking the ecological structure of marine microbial ecosystems. We demonstrate such ecological structure consisting of primary producer, primary degrader, and ultimate consumers is essential for achieving high power density and stability. Furthermore, the four-species microbial community is assembled into a spatial-temporally compacted cell using conductive hydrogel as a sediment-like anaerobic matrix, forming a miniaturized bionic ocean-battery. This battery directly converts light into electricity with a maximum power of 380 μW and stably operates for over one month. Reproducing the photoelectric conversion function of marine microbial ecosystems in this bionic battery overcomes the sluggish and network-like electron transfer, showing the biotechnological potential of synthetic microbial ecology.

Carbon Nanotube PtSn Nanoparticles for Enhanced Complete Biocatalytic Oxidation of Ethylene Glycol in Biofuel Cells

We report a hybrid catalytic system containing metallic PtSn nanoparticles deposited on multiwalled carbon nanotubes (Pt₆₅Sn₃₅/MWCNTs), prepared by the microwave-assisted method, coupled to the enzyme oxalate oxidase (OxOx) for complete ethylene glycol (EG) electrooxidation. Pt₆₅Sn₃₅/MWCNTs, without OxOx, showed good electrochemical activity toward EG oxidation and all the byproducts. Pt₆₅Sn₃₅/MWCNTs cleaved the glyoxilic acid C-C bond, producing CO₂ and formic acid, which was further oxidized at the electrode. Concerning EG oxidation, the catalytic activity of the hybrid system (Pt₆₅Sn₃₅/MWCNTs+OxOx) was twice the catalytic activity of Pt₆₅Sn₃₅/MWCNTs. Long-term electrolysis revealed that Pt₆₅Sn₃₅/MWCNTs+OxOx was much more active for EG oxidation than Pt₆₅Sn₃₅/MWCNTs: the charge increased by 65%. The chromatographic results proved that Pt₆₅Sn₃₅/MWCNTs+OxOx collected all of the 10 electrons per molecule of the fuel and was able to catalyze EG oxidation to CO₂ due to the associative oxidation between the metallic nanoparticles and the enzymatic pathway. Overall, Pt₆₅Sn₃₅/MWCNTs+OxOx proved to be a promising system to enhance the development of enzymatic biofuel cells for further application in the bioelectrochemistry field.

Development of a new biocathode for a single enzyme biofuel cell fuelled by glucose

In this study, we reported the development of Prussian blue (PB), poly(pyrrole-2-carboxylic acid) (PPCA), and glucose oxidase (GOx) biocomposite modified graphite rod (GR) electrode as a potential biocathode for single enzyme biofuel cell fuelled by glucose. In order to design the biocathode, the GR electrode was coated with a composite of PB particles embedded in the PPCA shell and an additional layer of PPCA by cyclic voltammetry. Meanwhile, GOx molecules were covalently attached to the carboxyl groups of PPCA by an amide bond. The optimal conditions for the biocathode preparation were elaborated experimentally. After optimization, the developed biocathode showed excellent electrocatalytic activity toward the reduction of H₂O₂ formed during GOx catalyzed glucose oxidation at a low potential of 0.1 V vs Ag/AgCl, as well as good electrochemical performance. An electrocatalytic current density of 31.68 ± 2.70 μA/cm² and open-circuit potential (OCP) of 293.34 ± 15.70 mV in O₂-saturated 10 mM glucose solution at pH 6.0 were recorded. A maximal OCP of 430.15 ± 15.10 mV was recorded at 98.86 mM of glucose. In addition, the biocathode showed good operational stability, maintaining 95.53 ± 0.15% of the initial response after 14 days. These results suggest that this simply designed biocathode can be applied to the construction of a glucose-powered single enzyme biofuel cell.

Mini-Review: Recent Technologies of Electrode and System in the Enzymatic Biofuel Cell (EBFC)

Enzymatic biofuel cells (EBFCs) is one of the branches of fuel cells that can provide high potential for various applications. However, EBFC has challenges in improving the performance power output. Exploring electrode materials is one way to increase enzyme utilization and lead to a high conversion rate so that efficient enzyme loading on the electrode surface can function correctly. This paper briefly presents recent technologies developed to improve bio-catalytic properties, biocompatibility, biodegradability, implantability, and mechanical flexibility in EBFCs. Among the combinations of materials that can be studied and are interesting because of their properties, there are various nanoparticles, carbon-based materials, and conductive polymers; all three have the advantages of chemical stability and enhanced electron transfer. The methods to immobilize enzymes, and support and substrate issues are also covered in this paper. In addition, the EBFC system is also explored and developed as suitable for applications such as self-pumping and microfluidic EBFC.

DNA derived N-doped 3D conductive network with enhanced electrocatalytic activity and stability for membrane-less biofuel cells

Enzymes are promising electrocatalysts in many biological processes. We proposed two strategies, co-immobilization and three-dimensional (3D) space design, to strengthen electron transfer (ET). In this research, DNA base and CNT were mixed in an aqueous solution; then the mixture was dried and ground. Finally, the powder was annealed in N₂ to obtain DNA derived N-doped 3D conductive network (N-G@CNT). N-G@CNT immobilized mediators on itself through adsorption. Such 3D space structure shows high activity toward a set of critical electrochemical reactions and high-performance in enzymatic biofuel cells (EBFCs). It is found that N-G@CNT conductive network possesses an interconnected porous structure and well-developed porosity. As a result, the membrane-less EBFCs equipped with enzyme/mediator co-immobilization N-G@CNT bioelectrodes were measured in a model 5 mM glucose-containing aqueous solution, human serum, and rabbit whole blood, respectively, which can generate 0.34, 0.078, and 0.15 mW cm^-2 power density, respectively. The constant-current discharge method carried out in a model 5 mM glucose-containing aqueous solution shows that the discharge time reached 19 h at a discharge current density of 0.01 mA cm^-2. The membrane EBFCs can deliver a high open circuit voltage of 0.68 V, a short-circuit current density of 2 mA cm^-2, and a maximum power density of 0.5 mW cm^-2.

Recent Advances in the Direct Electron Transfer-Enabled Enzymatic Fuel Cells

Direct electron transfer (DET), which requires no mediator to shuttle electrons from enzyme active site to the electrode surface, minimizes complexity caused by the mediator and can further enable miniaturization for biocompatible and implantable devices. However, because the redox cofactors are typically deeply embedded in the protein matrix of the enzymes, electrons generated from oxidation reaction cannot easily transfer to the electrode surface. In this review, methods to improve the DET rate for enhancement of enzymatic fuel cell performances are summarized, with a focus on the more recent works (past 10 years). Finally, progress on the application of DET-enabled EFC to some biomedical and implantable devices are reported.

Rational design of electroactive redox enzyme nanocapsules for high-performance biosensors and enzymatic biofuel cell

The potential application of biodevices based on enzymatic bioelectrocatalysis are limited by poor stability and electrochemical performance. To solve the limitation, modifying enzyme with functional polymer to tailor enzyme function is highly desirable. Herein, glucose oxidase (GOx) was chosen as a model enzyme, and according to the chemical structure of GOx cofactor (flavin adenine dinucleotide, FAD), we customize a biomimetic cofactor containing vinyl group (SFAD) for GOx, and prepared an GOx nanocapsule via in-situ polymerization. The characterization of particle size distribution, TEM, fluorescence and electrochemical performance indicated the successful formation of electroactive GOx nanocapsule with SFAD-containing polymeric network (n (GOx-SFAD-PAM)). The network can act as an electronic "highway" to link the active site with electrode, with capability to accelerate electron transfer as well as enhanced GOx stability. Further investigation of bioelectrocatalysis shows that n (GOx-SFAD-PAM)-based biosensor has low detection potential (-0.4 vs. Ag/AgCl), high sensitivity (64.97 μAmM^-1cm^-2), good anti-interference performance, quick response (3⁓5s) and excellent stability, and that n (GOx-SFAD-PAM)-based enzymatic biofuel cell (EBFC) has the high maximum power density (1011.21 μWcm^-2), which is a 385-fold increase over that of native GOx-based EBFC (2.62 μWcm^-2). This study suggests that novel enzyme nanocapsule with electroactive polymeric shell might provide a prospective solution for the performance improvement of enzymatic bioelectrocatalysis-based biodevices.

Optimization of rGO-PEI/Naph-SH/AgNWs/Frt/GOx nanocomposite anode for biofuel cell applications

The present study reports a new nanocomposite design using surface modified silver nanowires decorated on the surface of polyethyleneimine (PEI), a cationic polymer acting as glue for anchoring nanowires and reduced graphene oxide (rGO). The synthesized nanocomposite was employed as a promising electrode material for immobilization of biomolecules and effective transportation of electron, in enzymatic biofuel cell (EBFCs) application. The synthesized nanocomposite was confirmed by analytical techniques, for instance, Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), transmission electron microscopy (TEM). The electrochemical behaviour of the nanobioelectrocatalysts rGO-PEI/Frt/GOx, rGO-PEI/AgNWs/Frt/GOx, and rGO-PEI/Naph-SH/AgNWs/Frt/GOx was determined by cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), and linear sweep voltammetry (LSV). The maximum current density obtained by the modified bioanode was found to be 19.9 mA cm⁻² at the limiting glucose concentration of 50 mM in PBS (pH 7.0) as supporting electrolyte at a scan rate of 100 mVs⁻¹.

Engineering a diaphorase via directed evolution for enzymatic biofuel cell application

Background

Diaphorase (DI) has received wide attention as the key anodic enzyme mediating the electron transfer and electric energy generation in enzymatic biofuel cells (EBFCs). Lowering the anodic pH may be a useful strategy for constructing high-performance in EBFCs. However, most DI suffered from the poor activity at low pHs. Therefore, it is necessary to modify the activity and its acidic tolerance to further improve the performance of the EBFC.

Results

This paper attempts to improve the enzyme activity of DI originated from Geobacillus stearothermophilus under acidic conditions through directed evolution. Three rounds of random mutagenesis by error-prone PCR of the GsDI gene followed by high-throughput screening allowed the identification of the mutant 3–8 (H37Q, S73T, F105L, S68T, G61S, D74V) exhibiting a 4- or 7-fold increase in the catalytic activity at pH 5.4 or 4.5 compared to that of the wild type. And the pH stability of mutant 3–8 was significantly better than that of wild type and showed a 1.3 times higher in the stability at pH 5.4. The EBFC anode equipped with 0.5 mg of mutant 3–8 achieved a maximum current of 40 μA at pH 5.4, much higher than that with the same loading of the wild type enzyme.

Conclusion

The GsDI has been improved in the specific activity and pH stability by directed evolution which leads to the improvement of the EBFC performance. Also, the enlarged catalytic channel of mutant and decreased B-factor may be beneficial for the activity and stability. These results suggest that this engineered DI will be a useful candidate for the construction of enhanced EBFCs.

Cobalt sulfides/carbon nanohybrids: a novel biocatalyst for nonenzymatic glucose biofuel cells and biosensors

Exploring high-performance electrocatalysts is of great importance in developing nonenzymatic biofuel cells. Hybrid nanostructures with transition metal compounds and carbon nanomaterials exhibit excellent electrocatalytic activity and have emerged as promising low-cost alternatives for various electrochemical reactions. Herein, we report cobalt sulfide/carbon nanohybrids via a facile synthesis, which have excellent electrocatalytic activity for glucose oxidation and oxygen reduction reaction. The nonenzymatic glucose biofuel cells equipped with cobalt sulfide/carbon nanohybrids deliver a high open circuit voltage of 0.72 V with a maximum open power density of 88 μW cm⁻², indicating that cobalt sulfide/carbon nanohybrids are high performance biocatalysts for bioenergy conversion.

Exploring high-performance electrocatalysts is of great importance in developing nonenzymatic biofuel cells.