PEC thrombin aptasensor based on Ag-Ag2S decorated hematite photoanode with signal-down effect of precipitation catalyzed by G-quadruplexes/hemin

Highly efficient photoelectrochemical aptasensor based on CdS/CdTe QDs co-sensitized TiO2 nanoparticles designed for thrombin detection

A photoelectrochemical (PEC) sensor for the sensitive detection of thrombin (TB) was established. Co-sensitized combination of TiO2 nanoparticles combined with modified cadmium sulfide and cadmium telluride quantum dots (CdS/CdTe QDs) was utilized as a photoactive material. Successful growth of CdS/CdTe quantum dots on mesoporous TiO2 films occured by successive ion-layer adsorption and reaction. This interesting formation of co-sensitive structure is conducive to enhancing the photocurrent response by improving the use rate of light energy. Additionally, the step-level structure of CdS/CdTe QDs and TiO2 NPs shows a wide range of visible light absorption, facilitating the dissociation of excitons into free electrons and holes. Consequently, the photoelectric response of the PEC analysis platform is significantly enhanced. This constructed PEC aptasensor shows good detection of thrombin with a low detection limit (0.033 pM) and a wide linear range (0.0001-100 nM) in diluted actual human serum samples. In addition, this PEC aptasensor also has the characteristics of good stability and good reproducibility, which provides a novel insight for the quantitative measurement of other similar analytes.

Tetrahedral DNA Nanostructure-Engineered Paper-Based Electrochemical Aptasensor for Fumonisin B1 Detection Coupled with Au@Pt Nanocrystals as an Amplification Label

Fumonisin B1 (FB1), as one of the highest toxicity mycotoxins, poses a serious threat to animal and human health, even at low concentrations. It is significant and challenging to develop a sensitive and reliable analytical device. Herein, a paper-based electrochemical aptasensor was designed utilizing tetrahedral DNA nanostructures (TDNs) to controllably anchor an aptamer (Apt), improving the recognition efficiency of Apt to its target. First, gold nanoparticles (AuNPs)@MXenes were used as a sensing substrate with good conductivity and modified on the electrode for immobilization of complementary DNA-TDNs (cDNA-TDNs). In the absence of FB1, numerous Apt-Au@Pt nanocrystals (NCs) was hybridized with cDNA and assembled on the sensing interface, which accelerated the oxidation of TMB with H2O2 and produced a highly amplified differential pulse voltammetry (DPV) signal. When the target FB1 specifically bound to its Apt, the electrochemical signal was decreased by releasing the Apt-Au@Pt NCs from double-stranded DNA (dsDNA). On account of the strand displacement reaction by FB1 triggering, the aptasensor had a wider dynamic linear range (from 50 fg/mL to 100 ng/mL) with a lower limit of detection (21 fg/mL) under the optimized conditions. More impressively, the designed FB1 aptasensor exhibited satisfactory performance in corn and wheat samples. Therefore, the TDN-engineered sensing platform opens an effective approach for sensitive and accurate analysis of FB1, holding strong potential in food safety and public health.

A dual-cycle amplification-based electrochemical platform for sensitive detection of tobramycin

BACKGROUND

Tobramycin (TOB), an essential aminoglycoside antibiotic in human life, poses potential threats due to its residues in the environment. The primary concern is the adverse impact of excessive TOB on human kidneys, hearing, and other organs, significantly affecting human health. Constructing a sensitive electrochemical platform for simple and rapid trace detection is crucial. Herein, to enhance the sensitivity of TOB detection in the environment and mitigate the risks associated with residual antibiotics, an ultrasensitive electrochemical aptasensor was developed.

RESULTS

The sensor employs a dual-cycle amplification strategy involving catalytic hairpin assembly (CHA) and exonuclease III (Exo III) for efficient signal amplification. Simultaneously, the electrode performance was optimized by incorporating gold nanowires (AuNWs) onto the surface of reduced graphene oxide (PDA-rGO). Specifically, in the presence of TOB, which binds to the aptamer (Apt), dsDNA dissociates, releasing cDNA to open hairpin 1 (HP1) and initiate the CHA cycle with the participation of hairpin 2 (HP2). Exo III shears HP1 in the HP1/HP2 complex, freeing HP2 to participate in the CHA cycle again. Ultimately, a significant amount of signal label is retained on the electrode by hybridizing with sheared HP1, generating a robust electrical signal.

SIGNIFICANCE

Through the signal amplification strategy, the aptasensor design provides a broad linear range of 0.005-500 nM, with a low detection limit of 0.112 pM for TOB. It is worth mentioning that the aptasensor displayed favorable stability, specificity, and reproducibility, and has been successfully applied to practical samples, demonstrating its utility in practical applications.

Multi-signal aptasensor for thrombin detection based on catalytically active gold nanoparticles and fluorescent silicon quantum dots

A multi-signal aptasensor for thrombin determination is proposed based on catalytically active gold nanoparticles (AuNPs) and fluorescent silicon quantum dots (SiQDs). Yellow 4-Nitrophenol (4-NP) could be converted to colorless 4-Aminophenol (4-AP) by catalytically active aptamer-modified AuNPs (S1-AuNPs). The SiQDs emitted strong blue fluorescence at 455 nm at the excitation wavelength of 367 nm. When thrombin was absent, S1-AuNPs could catalytically reduce yellow 4-NP to colorless 4-AP. When thrombin was added, the aptamer could be transformed into a G-quadruplex structure, which masked the surface-active catalytic sites of AuNPs and restrained the reduction of 4-NP. Thus, the fluorescence of SiQDs was greatly quenched by 4-NP through the inner filter effect (IFE), and the solution color remained yellow. As the concentration of thrombin increased, the catalytic activity of S1-AuNPs decreased. The concentration of 4-NP that was converted to 4-AP declined and the unconverted 4-NP increased. In this process, the absorption peak of 4-NP at 400 nm increased while the fluorescence emission of SiQDs at 455 nm decreased. The linear ranges of the fluorometric and colorimetric aptasensor were 0.5-30 nM and 0.3-30 nM, respectively. The limits of detection (LOD) for the two modes were 0.15 nM and 0.13 nM. Furthermore, a portable sensing platform was constructed by combining the smartphone-based device with the software ImageJ for the determination of thrombin. With the advantages of cost-effectiveness, simplicity of operation and broad applicability, this aptasensor provided a new perspective for on-site determination of thrombin in the clinical field.