Pervaporation multilayer membranes based on a polyelectrolyte complex of λ-carrageenan and chitosan

Self-extinguished and flexible cation exchange membranes based on modified K-Carrageenan/PVA double network hydrogels for electrochemical applications

It is highly desired and yet challenging to develop eco-friendly cation exchange membranes with a combination of good mechanical, electrochemical, and biocompatible properties with a rational economic efficiency for given applications. In this study, new biocompatible double network (DN) hydrogels were prepared based on a blend of modified K-Carrageenan (KC) and polyvinyl alcohol (PVA). Acrylic acid (AA)-grafted KC (KC-g-(PAA)) and (AA-co-tertbutyl acrylate (TBA))-grafted KC (KC-g-P(AA-co-TBA)) were synthesized through an in situ free radical copolymerization. The grafted copolymers were blended with PVA and mixed with ZrOCl₂/KCl and glutaraldehyde (Glu) as the physical and chemical cross-linkers, respectively to produce KC-g-P(AA)/PVA and KC-g-P(AA-co-TBA)/PVA DN hydrogels. The membranes were prepared by a solution casting method. Various techniques were carried out to compare the structural, thermal, mechanical, flammability, and electrochemical properties of the membranes with those of the cross-linked KC, PVA, and KC/PVA membranes. The KC-g-P(AA-co-TBA)/PVA DN membrane showed more desirable properties as the cation exchange membrane with water uptake of 70.7 %, ion exchange capacity of 0.47 meq H⁺ /g, the ionic conductivity of 1.99 × 10^-2 S/cm², and elongation at break of 71.8 %. The prepared biopolymer membrane is very cost-effective and self-extinguished with admissible conductivity for electrochemical applications.

Non-Supported and PET-Supported Chitosan Membranes for Pervaporation: Production, Characterization, and Performance

The objective of this study was to develop non-supported and PET-supported chitosan membranes that were cross-linked with glutaraldehyde, then evaluate their physical-chemical, morphological, and mechanical properties, and evaluate their performance in the separation of ethanol/water and limonene/linalool synthetic mixtures by hydrophilic and target-organophilic pervaporation, respectively. The presence of a PET layer did not affect most of the physical-chemical parameters of the membranes, but the mechanical properties were enhanced, especially the Young modulus (76 MPa to 398 MPa), tensile strength (16 MPa to 27 MPa), and elongation at break (7% to 26%), rendering the supported membrane more resistant. Regarding the pervaporation tests, no permeate was obtained in target-organophilic pervaporation tests, regardless of membrane type. The support layer influenced the hydrophilic pervaporation parameters of the supported membrane, especially in reducing transmembrane flux (0.397 kg∙m-2∙h-1 to 0.121 kg∙m-2∙h-1) and increasing membrane selectivity (611 to 1974). However, the pervaporation separation index has not differed between membranes (228 for the non-supported and 218 for the PET-supported membrane), indicating that, overall, both membranes had a similar performance. Thus, the applicability of each membrane is linked to specific applications that require a more resistant membrane, greater transmembrane fluxes, and higher selectivity.

Nanocrystalline cellulose incorporated biopolymer tailored polyethersulfone mixed matrix membranes for efficient treatment of produced water

Membrane technology is a sustainable method to remove pollutants from petroleum wastewater. However, the presence of hydrophobic oil molecules and inorganic constituents can cause membrane fouling. Biomass derived biopolymers are promising renewable materials for membrane modification. In this study, fouling resistant biopolymer N-phthaloylchitosan (CS)- based polythersulfone (PES) mixed matrix membranes (MMMs) incorporated with nanocrystalline cellulose (NCC) was fabricated via phase inversion method and applied for produced water (PW) treatment. The morphological and Fourier-transform infrared spectroscopy (FTIR) analyses of the as-prepared NCC evidenced the formation of fibrous sheet-like structure and the presence of hydrophilic group. The membrane morphology and AFM analysis showed that the NCC altered the surface and cross-sectional morphology of the CS-PES MMMs. The tensile strength of NCC-CS-PES MMMs was also enhanced. 0.5 wt% NCC-CS-PES MMMs displayed a water permeability of 1.11 × 10^-7 m/s.kPa with the lowest contact angle value of 61°. It affirmed that its hydrophilicity increased through the synergetic interaction between CS biopolymer and NCC. The effect of process variables such as transmembrane pressure (TMP) and synthetic produced water (PW) concentration were evaluated for both neat PES and NCC-CS-PES MMMs membranes. 0.5 wt% NCC-CS-PES MMMs exhibited the highest PW rejection of 98% when treating 50 mgL^-1 of synthetic PW at a transmembrane pressure (TMP) of 200 kPa. The effect of nano silica and sodium chloride on the long-term PW filtration of NCC-CS-PES MMMs was also investigated.

The Potential of Polyelectrolyte Multilayer Films as Drug Delivery Materials

Polyelectrolyte multilayers (PEMs) represent a group of polyelectrolyte complex (PEC)–based materials widely investigated in the biomedical and pharmaceutical sciences. Despite the unflagging popularity of the aforementioned systems in tissue engineering, only a few updated scientific reports concerning PEM potential in drug administration can be found. In fact, PEM coatings are currently recognized as important tools for functionalizing implantable scaffolds; however, only a small amount of attention has been given to PEMs as drug delivery materials. Scientific reports on PEMs reveal two dominant reasons for the limited usability of multilayers in pharmaceutical technology: complex and expensive preparation techniques as well as high sensitivity of interacting polyelectrolytes to the varieties of internal and external factors. The aim of this work was to analyze the latest approaches, concerning the potential of PEMs in pharmacy, chemical technology, and (primarily) tissue engineering, with special attention given to possible polymer combinations, technological parameters, and physicochemical characteristics, such as hydrophilicity, adhesive and swelling properties, and internal/external structures of the systems formed. Careful recognition of the above factors is crucial in the development of PEM-based drug delivery materials.

Comparative Analysis of the Functional Properties of Films Based on Carrageenans, Chitosan, and Their Polyelectrolyte Complexes

The influence of the structural features of carrageenan on the functional properties of the films was studied. The carrageenans and chitosan films, as well as three-layer films containing a polyelectrolyte complex (PEC) of the two, were prepared. The X-ray diffractograms of carrageenan films reflected its amorphous structure, whereas chitosan and three-layer films were characterized by strong reflection in the regions of 20° and 15° angles, respectively. The SEM of the cross-sectional morphology showed dense packing of the chitosan film, as well as the layer-by-layer structure of different densities for the PEC. Among the tested samples, κ/β-carrageenan and chitosan films showed the highest tensile strength and maximum elongation. Films containing the drug substance echinochrome were obtained. Mucoadhesive properties were assessed as the ability of the films to swell on the mucous tissue and their erosion after contact with the mucosa. All studied films exhibited mucoadhesive properties. All studied films exhibited mucoadhesive properties which depended on the carrageenans structure. Multilayer films are stronger than single-layer carrageenan films due to PEC formation. The resulting puncture strength of the obtained films was comparable to that of commercial samples described in the literature.

Thermal Properties and Structural Features of Multilayer Films Based on Chitosan and Anionic Polysaccharides

This study investigates the thermal and structural properties of multilayer composites based on chitosan (CS) and polyanions with different functionalities, including sodium sulfoethyl cellulose (SEC), sodium alginate (ALG), and sodium hyaluronate (HA). Unlike polyelectrolyte complexes (PECs) obtained by polymer mixing, the formation of a PEC layer by a process of layer-by-layer deposition of oppositely charged polymers is accompanied by the transformation of the CS polymorphic state, and this affects the relaxation and thermal properties of the resulting multilayer composite. X-ray diffraction analysis showed that the formation of the PEC layer in the CS/SEC multilayer film is accompanied by crystallization of the CS chains and the formation of a predominantly anhydrous CS modification. Thermogravimetric analysis of the CS/SEC film registers a high-temperature peak associated with the thermal decomposition of crystalline CS in the PEC composition. According to the dynamic mechanical analysis, the CS/SEC composite was characterized by a single glass transition temperature, indicating a strong interaction between the layers when using SEC (a strong acid salt) as the counterion to CS. For multilayer composites with weak polyacid salts (ALG and HA), the crystallization of CS in the PEC layer is weaker, as reflected in the thermal degradation of these films. A high-temperature peak is recorded in the thermal decomposition of CS/HA and is absent in the case of CS/ALG. Dynamic mechanical analysis of the CS/ALG composite showed two glass transition temperatures close to those of the original polymers, indicating weak PEC formation. The CS/HA composite showed an intermediate response. Thus, the effect of the PEC layer on the properties of the poly-layer composites decreases in the order CS/SEC > CS/HA > CS/ALG.

Selective Oxidation of 2-Hydroxypropyl Ethers of Cellulose and Dextran: Simple and Efficient Introduction of Versatile Ketone Groups to Polysaccharides

Oxidation of polysaccharides has been a useful approach to new materials. However, selectivity in oxidation of polysaccharide macromolecular polyols remains a significant challenge with few methods for the synthesis of ketone-substituted polysaccharides. We report here a selective, practical, and efficient process, beginning with 2-hydroxypropyl ethers of polysaccharides that are simple and economical to prepare. We demonstrate this approach herein using commercial 2-hydroxypropyl cellulose (HPC) and 2-hydroxypropyl dextran (HPD) that we prepared. We oxidize the terminal, secondary alcohols of the oligo(2-hydroxypropyl) substituents with sodium hypochlorite so that the product has an oligo(2-hydroxypropyl) side chains terminated by a ketone. We demonstrate the high chemo- and regioselectivity of this oxidation by analytical methods including hydrolysis to monosaccharides and mass spectrometry of the resulting mixture. We provide an initial demonstration of the potential utility of these keto-polysaccharides by reacting Ox-HPC with primary amines to form Schiff base imines, providing proactive polymers.

Membranes for dehydration of alcohols via pervaporation

Alcohols are the essential chemicals used in a variety of pharmaceutical and chemical industries. The extreme purity of alcohols in many of such industrial applications is essential. Though distillation is one of the methods used conventionally to purify alcohols, the method consumes more energy and requires carcinogenic entertainers, making the process environmentally toxic. Alternatively, efforts have been made to focus research efforts on alcohol dehydration by the pervaporation (PV) separation technique using polymeric membranes. The present review is focused on alcohol dehydration using PV separation technique, which is the most efficient and benign method of purifying alcohols that are required in fine chemicals synthesis and developing pharmaceutical formulations. This review will discuss about the latest developments in the area of PV technique used in alcohol dehydration using a variety of novel membranes.

Pervaporation membranes of a simplex type with polyelectrolyte layers of chitosan and sodium hyaluronate

Self-supporting multilayer films containing a polyelectrolyte complex (PEC) were prepared by the sequential layering of sodium hyaluronate (HA, MW 5.4 × 10⁴) and chitosan (CS, MW 1.6 × 10⁵, the degree of deacetylation 0.80) in different orders. Imaging with low-voltage scanning electron microscopy (LVSEM) showed that the CS/HA films had a multilayer structure, while X-ray diffraction (XRD) indicated significant structuring of the CS layer near the PEC-CS region. Analysis of the thermal properties of the CS/HA films revealed differences in the structural organization and morphological features of the polymer layers and high thermal stability of the PEC layer. Testing of the transport properties of the CS/HA film in pervaporation (PV) separation using different compositions of ethanol-water mixtures indicated that the multilayer membrane was selective across a wide range of concentrations in the feed. Separation of an azeotropic ethanol-water mixture containing 5 wt% water yielded a permeate consisting of about 100 wt% water. LVSEM revealed that the membrane microstructure changed during the PV process due to membrane swelling and changes in the arrangement of the macromolecules during transport of the penetrant. The results support the use of CS/HA composite films as highly effective PV membranes. In addition to pervaporation separation, CS/HA multilayer films can also be used for drug delivery, tissue engineering, and wound healing applications.

New type of alginate/chitosan microparticle membranes for highly efficient pervaporative dehydration of ethanol

A new type of composite alginate membranes filled with chitosan (CS) and three different modified chitosan submicron particles, i.e. phosphorylated (CS-P), glycidol (CS-G) or glutaraldehyde (CS-GA) crosslinked ones, were prepared, and the pervaporation of water/ethanol mixture was investigated. The influence of various chitosan particles and their content on the transport properties of membranes was discussed. It was found that the addition of chitosan particles into the alginate matrix has a prominent effect on the ethanol/water separation efficiency. All tested membranes are characterized simultaneously by a high flux and selectivity, exhibiting advantageous properties, and outperforming numerous conventional materials. The best results were achieved for alginate membranes filled with phosphorylated chitosan particles at 10 wt%, for which separation factor, flux and PSI were equal to 136.2, 1.90 kg m-2 h-1 and 256.9 kg m-2 h-1, respectively.

Two-Ply Composite Membranes with Separation Layers from Chitosan and Sulfoethylcellulose on a Microporous Support Based on Poly(diphenylsulfone-N-phenylphthalimide)

Two-ply composite membranes with separation layers from chitosan and sulfoethylcellulose were developed on a microporous support based on poly(diphenylsulfone-N-phenylphthalimide) and investigated by use of X-ray diffraction and scanning electron microscopy methods. The pervaporation properties of the membranes were studied for the separation of aqueous alcohol (ethanol, propan-2-ol) mixtures of different compositions. When the mixtures to be separated consist of less than 15 wt % water in propan-2-ol, the membranes composed of polyelectrolytes with the same molar fraction of ionogenic groups (-NH₃⁺ for chitosan and -SO₃^- for sulfoethylcellulose) show high permselectivity (the water content in the permeate was 100%). Factors affecting the structure of a non-porous layer of the polyelectrolyte complex formed on the substrate surface and the contribution of that complex to changes in the transport properties of membranes are discussed. The results indicate significant prospects for the use of chitosan and sulfoethylcellulose for the formation of highly selective pervaporation membranes.