Preparation of high solid content oxidized starch by acid pretreatment–H2O2 oxidation and its performance as the ligand in zirconium tanning

Quaternization of cassava starch and determination of antimicrobial activity against bacteria and coronavirus

This study describes the novel development of quaternized cassava starch (Q-CS) with antimicrobial and antiviral properties, particularly effective against the MHV-3 coronavirus. The preparation of Q-CS involved the reaction of cassava starch (CS) with glycidyltrimethylammonium chloride (GTMAC) in an alkaline solution. Q-CS physicochemical properties were determined by FTIR, NMR, elemental analysis, zeta potential, TGA, and moisture sorption. FTIR and NMR spectra confirmed the introduction of cationic groups in the CS structure. The elemental analysis revealed a degree of substitution (DS) of 0.552 of the cationic reagent on the hydroxyl groups of CS. Furthermore, Q-CS exhibited a positive zeta potential value (+28.6 ± 0.60 mV) attributed to the high positive charge density shown by the quaternary ammonium groups. Q-CS demonstrated lower thermal stability and higher moisture sorption compared to CS. The antimicrobial activity of Q-CS was confirmed against Escherichia coli (MIC = 0.156 mg mL-1) and Staphylococcus aureus (MIC = 0.312 mg mL-1), along with a remarkable ability to inactivate 99% of MHV-3 coronavirus after only 1 min of direct contact. Additionally, Q-CS showed high cell viability (close to 100%) and minimal cytotoxicity effects, guaranteeing its safe use. Therefore, these findings indicate the potential use of Q-CS as a raw material for antiseptic biomaterials.

Production of Chemically Modified Bio-Based Wood Adhesive from Camote and Cassava Peels

Adhesives are significant for manufacturing competent, light, and sturdy goods in various industries. Adhesives are an important part of the modern manufacturing landscape because of their versatility, cost-effectiveness, and ability to enhance product performance. Formaldehyde and polymeric diphenylmethane diisocyanate (PMDI) are conventional adhesives utilized in wood applications and have been classified as carcinogenic, toxic, and unsustainable. Given the adverse environmental and health effects associated with synthetic adhesives, there is a growing research interest aimed at developing environmentally friendly bio-based wood adhesives derived from renewable resources. This study aimed to extract starch from camote and cassava peels and focuses on the oxidization of starch derived from camote and cassava peels using sodium hypochlorite to create bio-based adhesives. The mean yield of starch extracted from camote and cassava peels was 13.19 ± 0.48% and 18.92 ± 0.15%, respectively, while the mean weight of the oxidized starches was 34.80 g and 45.34 g for camote and cassava, respectively. Various starch ratios sourced from camote and cassava peels were examined in the production of bio-based adhesives. The results indicate that the 40:60 camote to cassava ratio yielded the highest solid content, while the 80:20 ratio resulted in the best viscosity. Furthermore, the 40:60 ratio produced the most favorable particle board in terms of mechanical properties, density, thickness, swelling, and water absorption. Consequently, the starch extracted from camote and cassava peels holds promise as a potential source for bio-based adhesives following appropriate chemical modification.

A novel synergistic covalence and complexation bridging strategy based on multi-functional biomass-derived aldehydes and Al(III) for engineering high-quality eco-leather

To get rid of the chrome pollution faced by the leather industry, we explored a novel engineering high-quality eco-leather technology based on the synergistic interactions between biomass-based aldehydes and Al(III). Firstly, dialdehyde xanthan gum (DXG) was prepared to covalently crosslink with the collagen fibers (CFs) via Schiff-base linkages under alkaline conditions, endowing the leather with a shrinkage temperature (Ts) of 80 °C and opening channels for the subsequent penetration of Al species (AL). Secondly, and for this latter purpose, the DXG-tanned leather was acidified to release part of the DXG from the leather according to the dynamic nature of the Schiff-base. Containing suitable oxygen-containing groups (OGs) with excellent complexation capabilities, the released DXG served as masking agents for AL, facilitating the penetration of AL into the inner CFs network for further complexation crosslinking. Consequently, a denser crosslinking network was constructed in the leather, and the crust leather exhibited higher Ts (82.2 °C), improved mechanical (tensile strength: 13.4 N/mm², tear strength: 53.3 N/mm) and organoleptic properties than those of the DXG crust or AL crust leathers. This demonstrates that this synergistic covalence and complexation bridging strategy is a sustainable option to substitute highly restricted chrome tanning agent for eco-leather production.