Solar photocatalytic inactivation of Fusarium Solani over TiO2 nanomaterials with controlled morphology—Formic acid effect

The Role of the Ferroelectric Polarization in the Enhancement of the Photocatalytic Response of Copper-Doped Graphene Oxide-TiO2 Nanotubes through the Addition of Strontium

To evaluate the potential role of in situ formed Sr-Ti-O species as a ferroelectric component able to enhance the photocatalytic properties of an adjacent TiO₂ semiconductor, Cu-doped/graphene oxide (GO)/TiO₂ nanotubes (TiNTs) composites (with 0.5 wt % Cu and 1.0 wt % GO) have been synthesized while progressive amounts of strontium (up to 1.0 wt %) were incorporated at the surface of the composite through incipient wetness impregnation followed by post-thermal treatment at 400 °C. The different resulting photocatalytic systems were then first deeply characterized by means of N₂ adsorption-desorption measurements, X-ray diffraction (XRD), UV-vis diffuse reflectance (UV-vis DR), Raman and photoluminescence (PL) spectroscopies, and scanning electron microscopy (SEM) (with energy-dispersive X-ray (EDX) spectroscopy and Z-mapping). In a second step, optimization of the kinetic response of the Sr-containing composites was performed for the formic acid photodegradation under UV irradiation. The Sr-containing Cu/GO/TiNT composites were then fully characterized by electrochemical impedance spectroscopy (EIS) for their dielectric properties showing clearly the implication of polarization induced by the Sr addition onto the stabilization of photogenerated charges. Finally, a perfect correlation between the photocatalytic kinetic evaluation and dielectric properties undoubtedly emphasizes the role of ferroelectric polarization as a very valuable approach to enhance the photocatalytic properties in an adjacent semiconductor.

Photocatalytic Inactivation of Enterobacter cloacae and Escherichia coli Using Titanium Dioxide Supported on Two Substrates

The antibacterial photocatalytic activity of TiO2 supported over two types of substrates, borosilicate glass tubes (TiO2/SiO2-borosilicate glass tubes (BGT)) and low-density polyethylene pellets (TiO2-LDPE pellets), which were placed in a compound parabolic collectors (CPC) reactor, was evaluated against Enterobacter cloacae and Escherichia coli under sunlight. Three solar photocatalytic systems were assessed, suspended TiO2, TiO2/SiO2-BGT and TiO2-LDPE pellets, at three initial bacterial concentrations, 1 × 105; 1 × 103; 1 × 101 CFU/mL of E. coli and total bacteria (E. cloacae and E. coli). The solar photo-inactivation of E. coli was achieved after two hours with 7.2 kJ/L of UV-A, while total bacteria required four hours and 16.5 kJ/L of UV-A. Inactivation order of E. coli was determined, as follows, suspended TiO2/sunlight (50 mg/L) > TiO2-LDPE pellets/sunlight (52 mg/L) > TiO2/SiO2-BGT/sunlight (59 mg/L), the best E. coli. inactivation rate was obtained with TiO2-LDPE pellets/sunlight, within 4.5 kJ/L and 90 min. The highest total bacteria inactivation rate was found for TiO2/sunlight (50 mg/L) and TiO2-LDPE pellets/sunlight (52 mg/L), within 11.2 kJ/L and 180 min. TiO2 deposited over LDPE pellets was the most effective material, which can be successfully used for water disinfection applications. Bacterial regrowth was assessed 24 h after all photocatalytic treatments, none of those microorganisms showed any recovery above the detection limit (2 CFU/mL).

Identifying the role of reactive oxygen species (ROSs) in Fusarium solani spores inactivation

The inactivation mechanism of photocatalytic disinfectants on bacteria is well known. In contrast, the potential inactivation of fungal spores by visible-light induced photocatalysis has been recognized, but the inactivation mechanism is poorly understood. We hypothesize that photocatalytically generated reactive oxygen species (ROSs) are directly involved in this mechanism. To test this hypothesis, we identified the roles of ROSs in the inactivation of Fusarium solani spores. As the photocatalysts, we doped TiO₂ with 3 typical dopants, forming Ag/TiO₂, N/TiO₂ and Er³⁺:YAlO₃/TiO₂. The Ag/TiO₂ photocatalysis was dominated by H₂O₂, with the longest lifetime among the investigated ROSs. Ag/TiO₂ photocatalysis yielded almost 100 % inactivation efficiency and preserved the cell-wall shape of the spores, thus minimizing the biomolecule leakage. Er³⁺:YAlO₃/TiO₂ was dominated by h⁺ ROSs, yielding an inactivation efficiency of 91 %; however, the severe leakage released large numbers of molecular bio-products. Severe damage to the cell walls by the h⁺ species was confirmed in micrograph observations. Subsequent to cell wall breakage, the Er³⁺:YAlO₃/TiO₂ nanoparticles entered the spore cells and directly oxidized the intracellular material. The N/TiO₂ photocatalysis, with •O₂⁻ dominated ROSs, delivered intermediate performance. In conclusion, photocatalysts that generate H₂O₂-dominated ROSs are most preferred for spore inactivation.

A review of heterogeneous photocatalysis for water and surface disinfection

Photo-excitation of certain semiconductors can lead to the production of reactive oxygen species that can inactivate microorganisms. The mechanisms involved are reviewed, along with two important applications. The first is the use of photocatalysis to enhance the solar disinfection of water. It is estimated that 750 million people do not have accessed to an improved source for drinking and many more rely on sources that are not safe. If one can utilize photocatalysis to enhance the solar disinfection of water and provide an inexpensive, simple method of water disinfection, then it could help reduce the risk of waterborne disease. The second application is the use of photocatalytic coatings to combat healthcare associated infections. Two challenges are considered, i.e., the use of photocatalytic coatings to give “self-disinfecting” surfaces to reduce the risk of transmission of infection via environmental surfaces, and the use of photocatalytic coatings for the decontamination and disinfection of medical devices. In the final section, the development of novel photocatalytic materials for use in disinfection applications is reviewed, taking account of materials, developed for other photocatalytic applications, but which may be transferable for disinfection purposes.