Investigation of Cu promotion effect on hydrotalcite-based nickel catalyst for CO2 methanation

Active Sites for CO2 Hydrogenation to Methanol: Mechanistic Insights and Reaction Control

Catalytic CO2 conversion to methanol is a promising way to extenuate the adverse effects of CO2 emission, global warming and energy shortage. Understanding the fundamental features of CO2 activation and hydrogenation at the molecular level is essential for carbon utilization and sustainable chemical production in the current climate crisis. This review explores the recent advances in understanding the design of catalysts with desired active sites, including single-atom, dual-atom, interface, defects/vacancies and promoters/dopants. We focused on the design of various catalytic systems to enhance their catalytic performances by stabilizing active metal in a catalyst, identifying the unique structure of active species, and engineering coordination environments of active sites. Mechanistic insights provided by advanced operando and in situ spectroscopies were also discussed. Moreover, the review highlights the key factors affecting active sites and reaction mechanisms, such as local environments, oxidation states, and metal-support interactions. By integrating recent advancements and relating knowledge gaps, this review aims to endow an inclusive overview of the field and guide future research toward more efficient and selective catalysts for CO2 hydrogenation to methanol.

Recent advances and progress in biotemplate catalysts for electrochemical energy storage and conversion

Complex structures and morphologies in nature endow materials with unexpected properties and extraordinary functions. Biotemplating is an emerging strategy for replicating nature structures to obtain materials with unique morphologies and improved properties. Recently, efforts have been made to use bio-inspired species as a template for producing morphology-controllable catalysts. Fundamental information, along with recent advances in biotemplate metal-based catalysts are presented in this review through discussions of various structures and biotemplates employed for catalyst preparation. This review also outlines the recent progress on preparation routes of biotemplate catalysts and discusses how the properties and structures of these templates play a crucial role in the final performance of metal-based catalysts. Additionally, the application of bio-based metal and metal oxide catalysts is highlighted for various key energy and environmental technologies, including photocatalysis, fuel cells, and lithium batteries. Biotemplate metal-based catalysts display high efficiency in several energy and environmental systems. Note that this review provides guidance for further research in this direction.

UV- and visible-light photocatalysis using Ni-Co bimetallic and monometallic hydrotalcite-like materials for enhanced CO2 methanation in sabatier reaction

The CO2 catalytic reduction activities of four different Co-modified Ni-based catalysts derived from hydrotalcite-like materials (HTCs) prepared by co-precipitation method were investigated under thermal and photocatalytic conditions. All catalysts were tested from 473 to 723 K at 10 bar (abs). The light intensity for photocatalytic reactions was 2.4 W cm-2. The samples were characterized to determine the effect of morphological and physicochemical properties of mono-bimetallic active phases on their methanation activity. The activity toward CO2 methanation followed the next order: Ni > Co-Ni > Co. For the monometallic Ni catalyst an increase of a 72% was achieved in the photo-catalytic activity under UV and vis light irradiation at temperatures lower by > 100 K than those in a conventional reaction. Co-modified Ni based hydrotalcite catalysts performed with stability and no deactivation for the 16 h studied under visible light for methanation at 523 K due to the presence of basic sites.

Engineering the Quaternary Hydrotalcite-Derived Ce-Promoted Ni-Based Catalysts for Enhanced Low-Temperature CO2 Hydrogenation into Methane

Ce-promoted NiMgAl mixed-oxide (NiCex-C, x = 0, 1, 5, 10) catalysts were prepared from the quaternary hydrotalcite precursors for CO₂ hydrogenation to methane. By engineering the Ce contents, NiCe5-C showed its prior catalytic performance in low-temperature CO₂ hydrogenation, being about three times higher than that of the Ce-free NiCe0-C catalyst (turnover frequency of NiCe5-C and NiCe0-C: 11.9 h^-1 vs. 3.9 h^-1 @ 225 °C). With extensive characterization, it was found that Ce dopants promoted the reduction of NiO by adjusting the interaction between Ni and Mg(Ce)AlOx support. The highest ratio of surface Ni⁰/(Ni²⁺ + Ni⁰) was obtained over NiCe5-C. Meanwhile, the surface basicity was tailored with Ce dopants. The strongest medium-strength basicity and highest capacity of CO₂ adsorption was achieved on NiCe5-C with 5 wt.% Ce content. The TOF tests indicated a good correlation with medium-strength basicity over the NiCex-C samples. The results showed that the high medium-strength and Ce-promoted surface Ni⁰ species endows the enhanced low-temperature catalytic performance in CO₂ hydrogenation to methane.

Hydrotalcite-Modified Clinoptilolite as the Catalyst for Selective Catalytic Reduction of NO with Ammonia (NH3-SCR)

A series of clinoptilolite-supported catalysts, modified with hydrotalcite-like phase (HT) by co-precipitation, were prepared and tested in NH₃-SCR reactions. It was found that deposition of HT on clinoptilolite increased conversion of NO within 250-450 °C, and that the positive impact on the catalytic activity was independent of HT loading. The promoting effect of clinoptilolite was attributed to Brönsted acid sites present in the zeolite, which facilitated adsorption and accumulation of ammonia during the catalytic process. Concentration of N₂O in the post-reaction gas mixture reached its maximum at 300 °C and the by-product was most likely formed as a consequence of NH₄NO₃ decomposition or side reaction of NH₃ oxidation in the high-temperature region. The gradual elimination of nitrous oxide, noticed as the material with the highest concentration of hydrotalcite phase, was attributed to the abundance of oligomeric iron species and the superior textural parameters of the material. UV-Vis experiments performed on the calcined samples indicated that Fe sites of higher nuclearity were generated by thermal decomposition of the hydrotalcite phase during the catalytic reaction. Therefore, calcination of the materials prior to the catalytic tests was not required to obtain satisfactory overall catalytic performance in NO reductions.

Ni-Based Catalyst for Carbon Dioxide Methanation: A Review on Performance and Progress

Catalytic conversion of CO2 into methane is an attractive method because it can alleviate global warming and provide a solution for the energy depletion crisis. Nickel-based catalysts were commonly employed in such conversions due to their high performance over cost ratio. However, the major challenges are that Ni tends to agglomerate and cause carbon deposition during the high-temperature reaction. In the past decades, extensive works have been carried out to design and synthesize more active nickel-based catalysts to achieve high CO2 conversion and CH4 selectivity. This review critically discusses the recent application of Ni-based catalyst for CO2 methanation, including the progress on the effect of supporting material, promoters, and catalyst composition. The thermodynamics, kinetics, and mechanism of CO2 methanation are also briefly addressed.

Co-Precipitated Ni-Mg-Al Hydrotalcite-Derived Catalyst Promoted with Vanadium for CO2 Methanation

Co-precipitated Ni-Mg-Al hydrotalcite-derived catalyst promoted with vanadium were synthesized with different V loadings (0–4 wt%) and studied in CO₂ methanation. The promotion with V significantly changes textural properties (specific surface area and mesoporosity) and improves the dispersion of nickel. Moreover, the vanadium promotion strongly influences the surface basicity by increasing the total number of basic sites. An optimal loading of 2 wt% leads to the highest activity in CO₂ methanation, which is directly correlated with specific surface area, as well as the basic properties of the studied catalysts.